Automotive Technology
7th Edition
ISBN: 9781337794213
Author: ERJAVEC, Jack.
Publisher: Cengage,
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 41, Problem 4SA
The four common configurations used as the final drives on FWD vehicles are the_____ gear,_____ gear,_______gear, and_____.
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
The four common configurations used as the finaldrives on FWD vehicles are the __ gear, __ gear,__ gear, and __
Words: Compress, Differential, Drive, Engine, Length, Power, Transmission, Torque, U-jointsA drive shaft must smoothly transfer ________________ while rotating, changing length, and moving up and down. Thedifferent designs of ________________shafts all attempt to ensure a vibration-free transfer of the engine’s________________from the transmission to the differential. This goal is complicated by the fact that the________________and transmission are bolted solidly to the frame of the car, whereas the ________________is mounted onsprings. As the rear wheels go over bumps in the road or changes in the road’s surface, the springs ________________or expand,changing the angle of the drive shaft between the ________________and the differential, as well as the distance between thetwo. To allow for these changes, the Hotchkiss-type drive shaft is fitted with one or more ________________to permit variationsin the angle of the drive, and a slip joint that permits the effective ________________of…
Words: Accelerating, Float, Gear, Noise, Tooth, VehicleCrown wheel and pinion noise originates from poor ________________ contact and may be noticed on drive, overdrive or________________. It can be more pronounced on one of these than on the others.Drive noise is most pronounced when ________________, as the gear teeth are under load. The bearings are also under loadso that any lack of preload will allow the ________________ teeth to change their area of contact.Noise on overdrive occurs as the ________________ decelerates from medium speeds, while float ________________occurs under light cruising conditions.
Chapter 41 Solutions
Automotive Technology
Ch. 41 - Explain the difference between rotary and vortex...Ch. 41 - What component keeps the stator assembly from...Ch. 41 - When a transmission is described as having two...Ch. 41 - The four common configurations used as the final...Ch. 41 - Three major types of rubber seals are used in...Ch. 41 - How can shift feel be controlled?Ch. 41 - What determines the timing of the shifts in an...Ch. 41 - Why must hydraulic line pressures increase when...Ch. 41 - Three major types of rubber seals are used in...Ch. 41 - True or False? The vent in a transmission housing...
Ch. 41 - True or False? The Ravigneaux gearset has one sun...Ch. 41 - To achieve a slow overdrive in a simple planetary...Ch. 41 - In a simple planetary gearset, when the planetary...Ch. 41 - Overrunning clutches are capable of_______. a....Ch. 41 - In the coupling stage of conventional torque...Ch. 41 - What is necessary for torque converter clutch...Ch. 41 - Technician A says that bearings that take radial...Ch. 41 - Technician A says that rotary oil flow is the oil...Ch. 41 - Technician A says that a stator aids in directing...Ch. 41 - Technician A says that a Simpson gearset is two...Ch. 41 - Technician A says that that one of the primary...Ch. 41 - Technician A says that the purpose of a valve body...Ch. 41 - Technician A says that changes in engine load...Ch. 41 - Technician A says that the rear hub of the torque...Ch. 41 - While discussing a Lepelletier system: Technician...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Words: Bearing, Bolts, Carrier, Case, Crown, Differential, Pinion, Preloaded, Shims, Spread, WheelThe differential side bearings are ________________ and this holds the differential case firmly in the housing. Whendismantling, the bearing mountings are usually ________________ slightly to relieve the preload so that the differential________________ with the crown wheel can be easily removed. The sequence is:1 Mark the left-hand and right-hand ________________ caps to identify their positions for reassembly.2 Remove the bearing cap ________________ and remove the bearing caps.3 Fit a spreader tool to the ________________ housing.4 Adjust the nut on the spreading tool to spread the housing so that the ________________ wheel and differential casecan be removed from the ________________.5 Remove the crown ________________ and differential case and release the spreader.6 Identify the right and left bearing cups and ________________ or spacers so that they can be correctly located…arrow_forwardThe typical RWD drive shaft rotates how many times faster than wheelsarrow_forward32. Technician A says hypoid gearset are only used in RWD vehicle drivetrains. Technician B says hypoid gearset multiply torque. Which technician is correct? A- Technician A B- Technician B C- Both A and B D- Neither A nor B.arrow_forward
- The drive shaft component that provides a means ofconnecting two or more shafts together is the __ .a. pinion flangeb. U-jointc. yoked. biscuitarrow_forwardWords: Backlash, Bearing, Combined, Cup, Dial, Gearset, Housing, Indicator, Position, Record, Shims, Spacers,Thickness, Tighten1 Measure the ________________ of the original side bearing preload shims.2 Install the differential case into the ________________.3 Install service ________________ that are the same thickness as the original preload shims between eachbearing ________________ and the housing.4 Install the bearing caps and finger ________________ the bolts.5 Mount a dial ________________ to the housing so that the button of the indicator touches the face of thering gear. Using two screwdrivers, pry between the ________________ and the housing. Pry to one side andset the dial indicator to zero, then pry to the opposite side and ________________ the reading.6 Select two shims with a ________________ thickness to that of the original shims plus the indicator reading,then install them.7 Using the proper tool, drive the shims into ________________ until they are fully seated.8…arrow_forwardWith a neat sketch explain the types of Drives used in automobile.arrow_forward
- Automotive technology chap 38 Ase style questions Thanks, automotive tech chap 38?arrow_forwardWhat are the different types of grooves found in belt drive?arrow_forwardWeight and Balance Find the Empty Weight CG location for the following tricycle gear aircraft. Each main wheel weighs 753 pounds, nose wheel weighs 22 pounds, distance between nose wheel and main wheels is 87.5 inches, nose wheel location is +9.875 inches from the datum, with 1 gallon of hydraulic fluid at –21 inches included in the aircraft weight. EWCG is _________________arrow_forward
- 1. Torque converter it is part of brake axle clutch Automatic transmission 2. .is the source of the power in the vehicle. dund engine clutch Automatic transmission 3. The final gear reduction in the drive train occurs in the. . assembly. drive shaft rear wheel friction disc differentialarrow_forwardHow is the speed of gearless traction elevator drive mechanisms varied?arrow_forwardIn front-wheel drivetrains, the CV joint nearer the transaxle is the____. a. inner joint b. inboard joint c. outboard joint d. both a and barrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Power Transmission; Author: Terry Brown Mechanical Engineering;https://www.youtube.com/watch?v=YVm4LNVp1vA;License: Standard Youtube License