Automotive Technology
7th Edition
ISBN: 9781337794213
Author: ERJAVEC, Jack.
Publisher: Cengage,
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 41, Problem 2ASRQ
Technician A says that bearings that take radial loads are called Torrington washers. Technician B says that bearings that take axial loads are called thrust washers. Who is correct?
a. Technician A only
b. Technician B only
c. Both A and B
d. Neither A nor B
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
Technician A says the size of the pads, shoes, drums, and rotors is based on the weight of the vehicle. Technician B says their size is based on the top speed the vehicle can achieve. Who is correct?
a. A only b. B only c. both A and B d. neither A nor B
If a force of 150 pounds is applied to a master cylinder with a piston area of 1 square inch, how much force is developed on a wheel cylinder that has a piston area of 2 square inches?
a. 75 pounds b. 150 pounds c. 300 pounds d. 450 pounds
While manually bleeding a brake system, Technician A loosens all the brake bleeder screws at the same time. Technician B uses shop air to push the fluid and air through the lines and out the bleeder screws. Who is correct?
a. A only b. B only c. both A and B d. neither A nor B
Brake fluid serves as a lubricant for the parts of the hydraulic system and ensures smooth and even operation.
a. True b. False
Technician A says the size of the pads, shoes, drums, and rotors is based on the weight of the vehicle. Technician B says their size is based on the top speed the vehicle can achieve. Who is correct?
a. A only b. B only c. both A and B d. neither A nor B
If a force of 150 pounds is applied to a master cylinder with a piston area of 1 square inch, how much force is developed on a wheel cylinder that has a piston area of 2 square inches?
a. 75 pounds b. 150 pounds c. 300 pounds d. 450 pounds
While manually bleeding a brake system, Technician A loosens all the brake bleeder screws at the same time. Technician B uses shop air to push the fluid and air through the lines and out the bleeder screws. Who is correct?
a. A only b. B only c. both A and B d. neither A nor B
Brake fluid serves as a lubricant for the parts of the hydraulic system and ensures smooth and even operation.
a. True b. False
Rusted-through brake lines are uncommon.
a. True b. False
A technician is diagnosing a vehicle with…
When trying to accommodate only axial loading, which of the following bearings is most likely to be used?
a. Tapered roller bearing
b. Deep groove ball bearing
c. Thrust bearing
d. Needle bearing
e. Spherical bearing
Chapter 41 Solutions
Automotive Technology
Ch. 41 - Explain the difference between rotary and vortex...Ch. 41 - What component keeps the stator assembly from...Ch. 41 - When a transmission is described as having two...Ch. 41 - The four common configurations used as the final...Ch. 41 - Three major types of rubber seals are used in...Ch. 41 - How can shift feel be controlled?Ch. 41 - What determines the timing of the shifts in an...Ch. 41 - Why must hydraulic line pressures increase when...Ch. 41 - Three major types of rubber seals are used in...Ch. 41 - True or False? The vent in a transmission housing...
Ch. 41 - True or False? The Ravigneaux gearset has one sun...Ch. 41 - To achieve a slow overdrive in a simple planetary...Ch. 41 - In a simple planetary gearset, when the planetary...Ch. 41 - Overrunning clutches are capable of_______. a....Ch. 41 - In the coupling stage of conventional torque...Ch. 41 - What is necessary for torque converter clutch...Ch. 41 - Technician A says that bearings that take radial...Ch. 41 - Technician A says that rotary oil flow is the oil...Ch. 41 - Technician A says that a stator aids in directing...Ch. 41 - Technician A says that a Simpson gearset is two...Ch. 41 - Technician A says that that one of the primary...Ch. 41 - Technician A says that the purpose of a valve body...Ch. 41 - Technician A says that changes in engine load...Ch. 41 - Technician A says that the rear hub of the torque...Ch. 41 - While discussing a Lepelletier system: Technician...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Which of the following is considered as the purpose why bearings are lubricated? a. To protect the bearing component from corrosion. b. To carry heat away from the bearing unit c. To help dissipate heat from the bearing unit. d. To provide low-friction film at the point of contact of rolling elements. e. All of the above.arrow_forwardWhen reviewing the procedure for replacing an axle boot, Technician A says that the position of the old boot should be marked on the shaft before removing it. Technician B says that if the boot is dimpled or collapsed after the new boot is installed, a dulled screwdriver should be used to allow air to enter the boot. Who is correct? O a. A only O b. B only O c. Both A and B O d. Neither A nor Barrow_forwardWhen discussing shift problems, Technician A says that worn or broken engine and transaxle mounts can cause a transaxle to have shifting problems. Technician B that poor shift boot alignment can cause a transaxle to jump out of gear. says Who is correct? A. A only C. Both A and B B. B only D. Neither A nor Barrow_forward
- Technician A says that most transaxles have a countershaftbetween the main and output shafts. TechnicianB says that a countershaft is always in motionwhen the engine is running. Who is correct?a. Technician A onlyb. Technician B onlyc. Both A and Bd. Neither A nor Barrow_forward9 Which of the following threads is ideal for power transmission? a. ACME Thread b. Square Thread c. Buttress Thread d. Metric Threadarrow_forwardTechnician A says that the piston seal retracts the caliper piston when hydraulic pressure is released. Technician B says that a return spring is used to retract a caliper piston. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forward
- Technician A says that broken or worn engine and transaxle mounts can cause a transaxie to have shiftinf problems.Technician B says that poor shift boot alignment can cause a transaxle to jump out of gear.Who is correct? a.Technician A only b.Technician B only c. both A and B d. Neither A or nor B.arrow_forwardTechnician A uses a micrometer to measure the connectingrod journal for taper. Technician B uses amicrometer to measure the connecting rod journalfor out-of-roundness. Who is correct?a. Technician Ab. Technician Bc. Both A and Bd. Neither A nor Barrow_forwardWhile discussing the different types of pressureplates: Technician A says that coil spring types arecommonly used because they have strong springs.Technician B says that Belleville-type pressure platesare not commonly used because they require excessivespace in the bell housing. Who is correct?a. Technician A onlyb. Technician B onlyc. Both A and Bd. Neither A nor Barrow_forward
- Industrial Maint. What are the three types of loads that may be placed on a bearing?arrow_forwardChoose the correct device pair from the following which is a common example for lower pair and self-closed pair. a. Roller and rings of bearing. b. Cam and follower. c. Gear mesh with another gear. d. Nut and bolt.arrow_forwardThe output shaft of a reducer is bearing in bearings A and B. From deep groove ball bearings, bed A is fixed and bed B is free-formed. Which of the following is true for the inner and Outer Ring of the bearing in bearing B?Please select one: a. Because the FG force acts on the shaft, there are no forces coming to the bracelets.b. the inner ring has a point, and the Outer Ring has an environmental load.c. Environmental load affects the outer ring.d. environmental load acts on the inner ring and point load acts on the outer ring.e. both environmental and point load affect the inner ring.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
BEARINGS BASICS and Bearing Life for Mechanical Design in 10 Minutes!; Author: Less Boring Lectures;https://www.youtube.com/watch?v=aU4CVZo3wgk;License: Standard Youtube License