Understanding Motor Controls
4th Edition
ISBN: 9781337798686
Author: Stephen L. Herman
Publisher: Delmar Cengage Learning
expand_more
expand_more
format_list_bulleted
Question
Chapter 37, Problem 12RQ
To determine
The size of the conductor used to supply the motors.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
Question 2
Beli vifth
Slack side
Motor
(imprut)
Tight side
Beli thickpess\
Centre distance
Figure 2
Figure 2 shows an open flat belt drive connected to a motor and a pulley. The
motor transmits 20 kw to the connect pulley of 450 mm diameter and is rotating
at 850 r/min to a second pulley rotating at 400 r/min. The distance between
pulley centres is approximately 2 m. The belt is 6 mm thick and has a density of
970 kg/m. The maximum stress in the belt is not to exceed 2,7 MPa. The
coefficient of friction for both pulleys is 0,3.
Determine:
2.1. The diameter of the second pulley.
2.2. The length of the belt.
3.3. The width of the belt taking centrifugal tension into account.
Please help me solve this question
please answer quickly!!
Chapter 37 Solutions
Understanding Motor Controls
Knowledge Booster
Similar questions
- Two transformers rated at 100 kVA each are connected in an open-delta connection. What is the total output power that can be supplied by this bank?arrow_forwardA large motor has a full load current rating of 425 amperes. Current transformers with a ratio of 600:5 are used to reduce the current to the overload heaters. What should be the full load current rating of the overload heaters?arrow_forwardA 480-volt three-phase load is rated at 34.5 kVA. It is to be supplied with variable three-phase voltage. Because the load is continuous, the transformers ratings are to be increased by 1.25% of the rated load. Three variable autotransformers are used to supply this load. Refer to Table 4-2 and determine the standard size of each transformer that should be used to make this connection.arrow_forward
- A 10 kVA transformer has a primary voltage rating of 240 volts and a secondary voltage rating of 480 volts. The transformer is connected to a circuit protected by a 100 ampere circuit breaker. The secondary is protected by a 25-ampere fuse. Does the primary require separate overcurrent protection?arrow_forwardDon't Use Chat GPT Will Upvote And Give Handwritten Solution Pleasearrow_forwardThere is a 3 HP, 220 Vrms single - phase induction motor that operates with a 0.85 lagging power factor and 80 9% efficiency. What is the magnitude of the RMS motor current? O 75 Amps 15 Amps O 5 Amps O 3 Ampsarrow_forward
- A 3-phase, 50 Hz, 3000 V motor develops 600 H.P. (447·6 kW), the power factor being 0·75 lagging andthe efficiency 0·93. A bank of capacitors is connected in delta across the supply terminals and powerfactor raised to 0·95 lagging. Each of the capacitance units is built of five similar 600-V capacitors.Determine the capacitance of each capacitor.arrow_forwardA 125-hp synchronous motor is connected to a 230-volt three-phase AC line. The motor is intended to operate at 80% power factor. What is the full-load running current of this motor? What are the minimum size NEMA and IEC starters that should be used to connect this motor to the line?arrow_forwardAn AC power source is connected across 325 turns of an autotransformer, and the load is connected across 260 turns. What is the turns ratio of this transformer?arrow_forward
- Ex: A single phase 50 KVA transformer has primary voltage of 6600 v and secondary voltage of 254 v and has 32 secondary turns. Calculate the number of primary turns and primary and secondary currents.arrow_forwardWhat is the peak voltage of a 120V RMS AC voltage?arrow_forwardQ A motor of 15 horsepower, has a code letter L, and is operated on a 400-volt line. Find the locked rotor currentarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Understanding Motor ControlsMechanical EngineeringISBN:9781337798686Author:Stephen L. HermanPublisher:Delmar Cengage LearningElectrical Transformers and Rotating MachinesMechanical EngineeringISBN:9781305494817Author:Stephen L. HermanPublisher:Cengage LearningRefrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Understanding Motor Controls
Mechanical Engineering
ISBN:9781337798686
Author:Stephen L. Herman
Publisher:Delmar Cengage Learning
Electrical Transformers and Rotating Machines
Mechanical Engineering
ISBN:9781305494817
Author:Stephen L. Herman
Publisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning