Degarmo's Materials And Processes In Manufacturing
13th Edition
ISBN: 9781119492825
Author: Black, J. Temple, Kohser, Ronald A., Author.
Publisher: Wiley,
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 37, Problem 12RQ
What magnitude of current might be required to produce resistance welds?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Sketch 2 NDT symbols illustrating different methods that can be used to indicate multiple test requirments for the same section of weld.
If you need narrow deep penetration weld for heavv base metal, which type of current polarity
you will use with DC current?
1) The development of residual stresses in
weld joint is due to?
O Heat treatment operations
OUnevenly distributed non-elastic strain
ONon-uniform heating and cooling
O All of the above
Chapter 37 Solutions
Degarmo's Materials And Processes In Manufacturing
Ch. 37 - What are the two primary functions of the...Ch. 37 - What are the two major roles of the applied...Ch. 37 - Why might resistance welding be considered a form...Ch. 37 - Why is there no need for fluxes or shielding gases...Ch. 37 - Prob. 5RQCh. 37 - What are the three components that contribute to...Ch. 37 - What measures can be taken to reduce the...Ch. 37 - What factors control the resistance between the...Ch. 37 - What are the possible consequences of too little...Ch. 37 - What is the ideal sequence for pressure...
Ch. 37 - Why do the resistance-welding conditions become...Ch. 37 - What magnitude of current might be required to...Ch. 37 - What are some of the changes that can occur in...Ch. 37 - What is the simplest and most widely used form of...Ch. 37 - What is the typical size of a spot-weld nugget?Ch. 37 - What are the two basic types of stationary...Ch. 37 - What is the major advantage of spot-welding guns?Ch. 37 - What are the pros and cons of a resistance spot...Ch. 37 - What are some of the properties that must be...Ch. 37 - What is the most common metal that is spot welded?Ch. 37 - What is the practical limit of the thicknesses of...Ch. 37 - What design features can be altered to permit the...Ch. 37 - What are the two methods used to produce...Ch. 37 - For what products would resistance butt welding be...Ch. 37 - What two limitations of spot welding can be...Ch. 37 - What limits the number of projection welds that...Ch. 37 - What are some of the attractive features of...Ch. 37 - What are some of the primary limitations to the...Ch. 37 - What type of metallurgical problem might be...Ch. 37 - What were some of the limitations that made the...Ch. 37 - What features promote coalescence in cold welding?Ch. 37 - Describe how the roll-bonding process can be used...Ch. 37 - Describe the friction welding process.Ch. 37 - How is inertia welding similar to friction...Ch. 37 - How are surface impurities removed in the...Ch. 37 - Why are inertia welds of more consistent quality...Ch. 37 - What are some of the geometric limitations of...Ch. 37 - How does linear friction welding differ from...Ch. 37 - How does friction-stir welding differ from...Ch. 37 - What are the primary process variables in...Ch. 37 - What are some of the attractive features of...Ch. 37 - What are some of the materials that have been...Ch. 37 - What is the benefit of adding a preheat laser to...Ch. 37 - Describe the friction-stir spot welding process.Ch. 37 - Prob. 45RQCh. 37 - How do ultrasonic vibrations produce a weld?Ch. 37 - What are some of the geometric limitations of...Ch. 37 - What are some of the attractive features of...Ch. 37 - What are the conditions necessary to produce...Ch. 37 - What kinds of materials can be joined by diffusion...Ch. 37 - How might intermediate layers be used to enhance...Ch. 37 - How are surface contaminants removed during...Ch. 37 - If the interface of a weld is viewed in cross...Ch. 37 - What are some typical applications of explosive...Ch. 37 - Many advanced engineering products, as well as...Ch. 37 - Using the Internet or technical literature,...Ch. 37 - Friction-stir processing is an interesting...Ch. 37 - Investigate the various types of power supplies...Ch. 37 - Consider a muffler being made entirely from...Ch. 37 - Prob. 2CSCh. 37 - Prob. 3CSCh. 37 - An alternate material might be one-side...Ch. 37 - Prob. 5CS
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
A piston/cylinder has a water volume separated in VA=0.2m3 and VB=0.3m3 by a stiff membrane (Fig. P3.139). The ...
Fundamentals Of Thermodynamics
What parts are included in the vehicle chassis?
Automotive Technology: Principles, Diagnosis, And Service (6th Edition) (halderman Automotive Series)
11.12 A short post. by, of Douglas fir, is reinforced by the addition of two ASTM steel plates. The cross sec...
Applied Statics and Strength of Materials (6th Edition)
Determine the tension developed in cables AB, AC, and AD.
Engineering Mechanics: Statics
ICA 8-20
A eutectic alloy of two metals contains the specific percentage of each metal that gives the lowest po...
Thinking Like an Engineer: An Active Learning Approach (3rd Edition)
Use data for specific volume to calculate and plot the speed of sound in saturated liquid water over the tempe...
Fox and McDonald's Introduction to Fluid Mechanics
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- What effect does shortening the electrode extension have on weld penetration?arrow_forwardWhat arc problems can occur in deep or narrow weld joints?arrow_forwardWhat chemicals alloys are a. considered to be contaminants to the weld metal? b. used to increase tensile strength in the weld metal? c. used to increase corrosion resistance? d. used to reduce creep?arrow_forward
- What alloying element used in FCA welding electrodes causes the electrode to produce centerline cracks in the weld if it is used for multipass welds?arrow_forwardAs stricter standards are applied to the welding process, what happens to the cost of the weldment?arrow_forwardIn short-circuiting transfer, what type of current alloys the liquid metal at the electrode tip to be transferred by direct contact with the molten weld pool?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Differences between Temporary Joining and Permanent Joining.; Author: Academic Gain Tutorials;https://www.youtube.com/watch?v=PTr8QZhgXyg;License: Standard Youtube License