EBK MANUFACTURING ENGINEERING & TECHNOL
7th Edition
ISBN: 8220100793431
Author: KALPAKJIAN
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Question
Chapter 34, Problem 39SDP
To determine
Collect some pieces of small metal parts and perform the water break test on them. Then clean the surfaces with various cleaning fluids and repeat the test. Explain your observations.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
How can machinery parts and pipeline welds be tested for flies without destroying them? name several processes?
QUESTION 5
Assuming a cylinder of molten plastics with a starting radius of 8.8mm and hieght of 1.8 mm, what is fe height after 4 sec, if a force of 57 N is
applied. Assume a viscosity of 1,082 Pa*sec.
Do not provide handwritten solution,Maintain accuracy and quality in your answer,Take care of plagiarism,Answer completely,You will get up vote for sure.
Chapter 34 Solutions
EBK MANUFACTURING ENGINEERING & TECHNOL
Ch. 34 - Explain why surface treatments may be necessary...Ch. 34 - What is shot peening? Why is it performed?Ch. 34 - What are the advantages of roller burnishing?Ch. 34 - Explain the difference between case hardening and...Ch. 34 - Describe the principles of physical and chemical...Ch. 34 - Review Fig. 34.2 and describe the principles...Ch. 34 - Prob. 7RQCh. 34 - Prob. 8RQCh. 34 - Prob. 9RQCh. 34 - Prob. 10RQ
Ch. 34 - Prob. 11RQCh. 34 - Prob. 12RQCh. 34 - Prob. 13RQCh. 34 - Prob. 14RQCh. 34 - Prob. 15RQCh. 34 - Prob. 16RQCh. 34 - Describe how roller-burnishing processes induce...Ch. 34 - Explain why some parts may be coated with...Ch. 34 - Prob. 19QLPCh. 34 - Prob. 20QLPCh. 34 - Prob. 21QLPCh. 34 - It is well known that coatings may be removed or...Ch. 34 - Make a list of the coating processes described in...Ch. 34 - Sort the coating processes described in this...Ch. 34 - Why is galvanizing important for automotive-body...Ch. 34 - Explain the principles involved in various...Ch. 34 - Taking a simple example, such as the parts shown...Ch. 34 - Estimate the plating thickness in electroplating a...Ch. 34 - Which surface treatments are functional, and which...Ch. 34 - An artificial implant has a porous surface area...Ch. 34 - If one is interested in obtaining a textured...Ch. 34 - It is known that a mirrorlike surface finish can...Ch. 34 - It has been observed in practice that a thin layer...Ch. 34 - Prob. 34SDPCh. 34 - Prob. 35SDPCh. 34 - Because they evaporate, solvents and similar...Ch. 34 - Prob. 37SDPCh. 34 - The shot-peening process can be demonstrated with...Ch. 34 - Prob. 39SDPCh. 34 - Prob. 40SDP
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Why is the backing strip 2 in. (50 mm) longer than the test plate?arrow_forwardSelect all answers that are correct. Which of the following statements explain why solids have shapes and fluids do not? O A fluid develops a finite deformation when subjected to a shear stress a A fluid deforms continuously when subjected to a shear stress A solid develops a finite deformation when subjected to a shear stress O A solid deforms continuously when subjected to a shear stressarrow_forwarda) During sliding of a cylindrical steel pin against a steel disc in a pin-on-disc test in air, the coefficient of friction is initially around 0.7, but then falls to 0.5 as the test proceeds. At the end of the test, the wear track on the disc is rough and black in colour, with a black powder on the disc surface outside the wear track; chemical analysis of the wear track shows a high oxygen level. (b) A test identical to that described in part (a) is conducted, but this time the test is conducted in vacuum. The coefficient of friction remains high through the test, the wear volumes are much greater, and the track on the disc surface following the test is very rough and silvery in colour. (c) A test identical to that described in part (a) is conducted, but this time the test is conducted in air at 300 ◦C. At the end of the test, the wear track on the disc is very smooth (shiny) and black in colour, with no debris on the disc surface outside the weartrack; chemical analysis of the wear…arrow_forward
- In the hardness test, answer the questions 1- What happens to the sample if its thickness is less than 10h 2- What happens to the sample if its prayer is more than one prayer after the effect? 3- What happens to the sample if its hardness is higher than the hardness of the ball?arrow_forwardA part made of sheet steel is to be nickel plated. The part is a rectangular flat plate that is 0.075 cm thick and whose face dimensions are 14 cm by 19 cm. The plating operation is carried out in an acid sulfate electrolyte, using a current = 20 amps for a duration = 30 min. Determine the average thickness of the plated metal resulting from this operation. Assume, C= 3.42 x 102 mm/A-s, cathode efficiency E = 95%.arrow_forwardWhat exactly is stress testing, and how does it help?arrow_forward
- Which one of these may increase the amount of contact resistance? Using air as a fluid for the gap instead of liquids decreasing pressure for pressing the materials together Lower temperature during matching of materials All of the given Higher surface roughnessarrow_forwardkindly help me with this one please. Thank you! Asap :( General Instructions:>>Show the complete and organize solution. Write your answer with four decimal places and enclose them in a box. Solve as neatly as possible. FOLLOW THIS FORMAT ( GIVEN REQUIRED SOLUTION)arrow_forwardThere may be cases where an extensometer is used in the metal tensile test and cases where it is not. At this time, explain the part where the most difference appears in analyzing the results of the two experiments.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Properties of Fluids: The Basics; Author: Swanson Flo;https://www.youtube.com/watch?v=TgD3nEO1iCA;License: Standard YouTube License, CC-BY
Fluid Mechanics-Lecture-1_Introduction & Basic Concepts; Author: OOkul - UPSC & SSC Exams;https://www.youtube.com/watch?v=6bZodDnmE0o;License: Standard Youtube License