EBK MANUFACTURING ENGINEERING & TECHNOL
7th Edition
ISBN: 9780100793439
Author: KALPAKJIAN
Publisher: YUZU
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Question
Chapter 32, Problem 30QTP
To determine
Determine the maximum tensile force that the given joint can withstand.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Understand cohesive and adhesive forces.
What do you understand by the term riveted joint? Explain the necessity of such a joint.
Enumerate the different types of riveted joints and rivets.
Chapter 32 Solutions
EBK MANUFACTURING ENGINEERING & TECHNOL
Ch. 32 - What is the difference between brazing and...Ch. 32 - Are fluxes necessary in brazing? If so, why?Ch. 32 - Why is surface preparation important in...Ch. 32 - What materials are typically used in solder?Ch. 32 - Soldering is generally applied to thinner...Ch. 32 - Explain the reasons why a variety of mechanical...Ch. 32 - List three brazing and three soldering techniques.Ch. 32 - Describe the similarities and differences between...Ch. 32 - What precautions should be taken in the...Ch. 32 - What difficulties are involved in joining...
Ch. 32 - Prob. 11RQCh. 32 - What are the principles of (a) wave soldering...Ch. 32 - What is a peel test? Why is it useful?Ch. 32 - What is a combination joint?Ch. 32 - Prob. 15RQCh. 32 - Prob. 16QLPCh. 32 - Prob. 17QLPCh. 32 - Comment on your observations concerning the...Ch. 32 - Give examples of combination joints other than...Ch. 32 - Discuss the need for fixtures for holding...Ch. 32 - Explain why adhesively bonded joints tend to be...Ch. 32 - It is common practice to tin-plate electrical...Ch. 32 - Give three applications where adhesive-bonding is...Ch. 32 - Prob. 24QLPCh. 32 - If you are designing a joint that must be strong...Ch. 32 - Prob. 26QLPCh. 32 - Rate lap, butt, and scarf joints in terms of...Ch. 32 - Prob. 28QLPCh. 32 - Prob. 29QTPCh. 32 - Prob. 30QTPCh. 32 - Prob. 31QTPCh. 32 - Figure 32.4 shows qualitatively the tensile and...Ch. 32 - When manufacturing the fuselage of a commuter...Ch. 32 - Prob. 34SDPCh. 32 - Name several products that have been assembled...Ch. 32 - Suggest methods of attaching a round bar (made of...Ch. 32 - Prob. 38SDPCh. 32 - Prob. 39SDPCh. 32 - Prob. 40SDPCh. 32 - Prob. 41SDPCh. 32 - Describe part shapes that cannot be joined by...Ch. 32 - Prob. 43SDPCh. 32 - Prob. 44SDPCh. 32 - Prob. 45SDPCh. 32 - Prob. 46SDPCh. 32 - Review Fig. 32.9a and explain the shortcoming...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- 7(a) What is the difference between a prismatic joint and a revolute joint?arrow_forwardThe maximum force in a rivet in a riveting group under eccentric loadingarrow_forward19. Describe and explain, with the aid of diagrams, the phenomenon of die swell and how it may be reduced or compensated for in polymer extrusion techniques.20. Describe (with the aid of any diagrams as appropriate) two types of defect that may be encountered in a welded metal joint 21. With reference to optimising the use of weld metal, outline (with the aid of any diagrams as appropriate) two considerations given to welded joint design. 22. Outline the use of liquid (dye/fluorescent) penetrants as a non-destructive testing method. 23. Outline (with the aid of any diagrams if needed) four limitations of adhesive bonding. 24. Threaded components (i.e. screws, nuts, bolts) and rivets are commonly used mechanical fasteners. Describe, with the aid of diagrams, two other methods of mechanical fastening that are also used in manufacturing. answer all partsarrow_forward
- Example 27.2. A 100 mm x 10 mm plate is to be 150 mm x 10 mm by the fillet welding on three sides. The size of the weld is 6 mm. Find out the necessary over lap of the plate, for full strength of the joint. Take allowable tensile stress in plate equal to 150 N/mm and allowable stress in weld as 110 N/mm. welded to another platearrow_forwardA compound die will be used to blank and punch a large washer out of 6061ST aluminum alloy sheet stock 4.50 mm thick. The outside diameter of the washer is 60.0 mm and the inside diameter is 25.0 mm. Determine the punch and die sizes for the blanking operation. Determine the force required to perform the blanking and punching operation, assuming that the punches are staggered so that punching occurs first, then blanking. The aluminum sheet metal has a tensile strength = 310 MPa. Consider a clearance allowance value of 0.060.arrow_forward2) Explain how a cylindrical joint can be practically realised?arrow_forward
- (4) The average flow stress is the flow stress multiplied by which of the following factors: (a) n, (b) (1-n), (c) 1/n, or (d) 1/(1+n), where n is the strain hardening exponent? (5) The strength of a brazed joint is typically (a) equal to, (b) stronger than, or (c) weaker than soldered joint? (6) Thread cutting operation is normally performed on which one of the following machine tools: (a) drill press, (b) lathe, (c) milling machine, (d) planer, or (e shaper? (7) Of the following cutting conditions, which one has the greatest effect on cutting temperature: (a) cutting speed, (b) depth of cut, or (c) feed? (8) The maximum possible draft in a rolling operation depends on which of the following parameters (two correct answers): (a) coefficient of friction, (b) roll diameter, (c) roll velocity, (d) stock thickness, (e) strainarrow_forwardType a detailed note about the USES OF SANDWICH PANELS. also mention the references.arrow_forwardA welding operation is time-studied during which an operator was pace-rated as 120%. The operator took, on an average, 8 minutes for producing the weld-joint. If a total of 10% allowances are allowed for this operation. What is the expected standard production rate of the weld-joint in units per 8 hour day?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Metal Joining Process-Welding, Brazing and Soldering; Author: Toc H Kochi;https://www.youtube.com/watch?v=PPT5_fDSzGY;License: Standard YouTube License, CC-BY