EBK MANUFACTURING ENGINEERING & TECHNOL
7th Edition
ISBN: 9780100793439
Author: KALPAKJIAN
Publisher: YUZU
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Question
Chapter 32, Problem 29QTP
(a)
To determine
Calculate the minimum and maximum tensile force that the given joint can withstand.
(b)
To determine
Calculate the forces for the lap joint, if the area is
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Understand cohesive and adhesive forces.
Write down the damage patterns that occur in the rivet joints that are forced axially. Explain how strength calculations are made under static stresses.
11.17D
Develop a chart from other references that presents the properties and applications
of engineering adhesives. Organize the chart (table) according to (a) chemical type,
Chapter 32 Solutions
EBK MANUFACTURING ENGINEERING & TECHNOL
Ch. 32 - What is the difference between brazing and...Ch. 32 - Are fluxes necessary in brazing? If so, why?Ch. 32 - Why is surface preparation important in...Ch. 32 - What materials are typically used in solder?Ch. 32 - Soldering is generally applied to thinner...Ch. 32 - Explain the reasons why a variety of mechanical...Ch. 32 - List three brazing and three soldering techniques.Ch. 32 - Describe the similarities and differences between...Ch. 32 - What precautions should be taken in the...Ch. 32 - What difficulties are involved in joining...
Ch. 32 - Prob. 11RQCh. 32 - What are the principles of (a) wave soldering...Ch. 32 - What is a peel test? Why is it useful?Ch. 32 - What is a combination joint?Ch. 32 - Prob. 15RQCh. 32 - Prob. 16QLPCh. 32 - Prob. 17QLPCh. 32 - Comment on your observations concerning the...Ch. 32 - Give examples of combination joints other than...Ch. 32 - Discuss the need for fixtures for holding...Ch. 32 - Explain why adhesively bonded joints tend to be...Ch. 32 - It is common practice to tin-plate electrical...Ch. 32 - Give three applications where adhesive-bonding is...Ch. 32 - Prob. 24QLPCh. 32 - If you are designing a joint that must be strong...Ch. 32 - Prob. 26QLPCh. 32 - Rate lap, butt, and scarf joints in terms of...Ch. 32 - Prob. 28QLPCh. 32 - Prob. 29QTPCh. 32 - Prob. 30QTPCh. 32 - Prob. 31QTPCh. 32 - Figure 32.4 shows qualitatively the tensile and...Ch. 32 - When manufacturing the fuselage of a commuter...Ch. 32 - Prob. 34SDPCh. 32 - Name several products that have been assembled...Ch. 32 - Suggest methods of attaching a round bar (made of...Ch. 32 - Prob. 38SDPCh. 32 - Prob. 39SDPCh. 32 - Prob. 40SDPCh. 32 - Prob. 41SDPCh. 32 - Describe part shapes that cannot be joined by...Ch. 32 - Prob. 43SDPCh. 32 - Prob. 44SDPCh. 32 - Prob. 45SDPCh. 32 - Prob. 46SDPCh. 32 - Review Fig. 32.9a and explain the shortcoming...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- What do you understand by the term riveted joint? Explain the necessity of such a joint.arrow_forwardWhat do you understand by the term welded joint? How it differs from riveted joint?arrow_forwardDiscuss the significance of the initial tightening load and the applied load so far as bolts are concerned. Explain which of the loads must be greater for a properly designed bolted joint and explain how each affects the total load on the bolt.arrow_forward
- a) A bicycle frame is being designed to carry a pedal force of 800N. Assuming axial loading only, which material will produce the lightest frame out of the two in the table below? Assume a design factor of 1.2 b) If the bicycle frame is being welded together and an internal flaw size of 30mm results, which material will produce the lighter section? (Apply a design factor of 1.2 If the bicycle frame needs to last a minimum 3 x 105 cycles, with an average stress of 150MPa and an alternating stress of 200MPa, use the Soderberg criterion to pick a suitable material from the two alloys listed above. Show all your working.arrow_forwardQuestion 01: Draw and label any screw thread and a fastener separately. Also, discuss the types of stresses acting on screw threads and fasteners.arrow_forward19. Describe and explain, with the aid of diagrams, the phenomenon of die swell and how it may be reduced or compensated for in polymer extrusion techniques.20. Describe (with the aid of any diagrams as appropriate) two types of defect that may be encountered in a welded metal joint 21. With reference to optimising the use of weld metal, outline (with the aid of any diagrams as appropriate) two considerations given to welded joint design. 22. Outline the use of liquid (dye/fluorescent) penetrants as a non-destructive testing method. 23. Outline (with the aid of any diagrams if needed) four limitations of adhesive bonding. 24. Threaded components (i.e. screws, nuts, bolts) and rivets are commonly used mechanical fasteners. Describe, with the aid of diagrams, two other methods of mechanical fastening that are also used in manufacturing. answer all partsarrow_forward
- Determine the effects of two-dimensional and three-dimensional loading on the dimensions of a given material with regard to a simple joining block.arrow_forwardA three point bend test is performed on a block of ZrO2 that is 8 in.long,0.50.in.wide,and 0.25 in.thick and is resting on two supports 4 in.apart.when a force of 400 lb is applied ,the specimen deflects 0.037 in.and breaks.Calculate (a) the flexural strength ;and (b) the flexural modulus,assuming that no plastic deformation occurs.arrow_forwardi need the answer quicklyarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
EVERYTHING on Axial Loading Normal Stress in 10 MINUTES - Mechanics of Materials; Author: Less Boring Lectures;https://www.youtube.com/watch?v=jQ-fNqZWrNg;License: Standard YouTube License, CC-BY