Welding: Principles and Applications (MindTap Course List)
8th Edition
ISBN: 9781305494695
Author: Larry Jeffus
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 31, Problem 20R
Why is a neutral flame the most commonly used oxyacetylene flame used?
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
28. The shaft shown in Figure P5-28 is supported by bear-
ings at each end, which have bores of 20.0 mm. Design
the shaft to carry the given load if it is steady and the
shaft is stationary. Make the dimension a as large as pos-
sible while keeping the stress safe. Determine the required
d = 20mm
D = ?
R = ?|
5.4 kN d=20mm
Length not
to scale
-a = ?-
+а=
a = ? +
-125 mm-
-250 mm-
FIGURE P5-28 (Problems 28, 29, and 30)
2. A strut in a space frame has a rectangular cross section
of 10.0 mm by 30.0 mm. It sees a load that varies from a
tensile force of 20.0 kN to a compressive force of 8.0 kN.
find stress at Q
Chapter 31 Solutions
Welding: Principles and Applications (MindTap Course List)
Ch. 31 - What is the purpose of a pressure regulator?Ch. 31 - What may result if a pressure regulator is not...Ch. 31 - Describe how a single-stage regulator operates.Ch. 31 - Is the torch pressure always the same as the...Ch. 31 - Why does the high-pressure gauge on a regulator...Ch. 31 - How does the operation of a safety release valve...Ch. 31 - Describe the difference between an argon cylinder...Ch. 31 - What is meant by regulator creep?Ch. 31 - Who can repair regulators?Ch. 31 - Why must the pressure be released from a regulator...
Ch. 31 - Why are combination welding and cutting torches...Ch. 31 - What is the advantage of using an injector-type...Ch. 31 - What should be done to the valve packing if the...Ch. 31 - What may happen to a tip seat if it is incorrectly...Ch. 31 - What can happen to a tip if it is excessively...Ch. 31 - What is the difference between a reverse flow...Ch. 31 - What are Siamese hoses?Ch. 31 - Why must the pressure be bled off hoses when work...Ch. 31 - What is the difference between a backfire and a...Ch. 31 - Why is a neutral flame the most commonly used...Ch. 31 - What properties should a good leak-detecting...Ch. 31 - Why must the oxygen cylinder valve be opened all...Ch. 31 - How long should hoses be purged?Ch. 31 - What should be done with cylinders that have...Ch. 31 - How should the spark lighter be held to light a...Ch. 31 - Once the torch is lit, why must the acetylene flow...Ch. 31 - What type of piping can be used for a manifold...Ch. 31 - What elements make up all hydrocarbons?Ch. 31 - What are the separate parts that make up an...Ch. 31 - Use Table 31-3 to determine which fuel gas...Ch. 31 - Approximately how long would it take a 50/50...Ch. 31 - Use Table 31-4 to determine which fuel gas has the...Ch. 31 - How is acetylene produced?Ch. 31 - Why is it not safe to use acetylene above 15 psig...Ch. 31 - Use Table 31-5 to determine the largest tip...Ch. 31 - Where is the highest temperature and where is the...Ch. 31 - Use Table 31-6 to determine what would be the...Ch. 31 - What are methylacetylene-propadiene fuel gases...Ch. 31 - Use Table 31-7 to determine which oxygen fuel-gas...Ch. 31 - Which fuel gas has the strongest odor and is...Ch. 31 - What is the major advantage of using propane or...Ch. 31 - Use Table 31-8 to determine which fuel gas would...Ch. 31 - What two major safety problems does hydrogen...Ch. 31 - Why should coat hangers not be used as gas welding...Ch. 31 - Explain the significance of the AWS filler metal...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- I had a theoretical question about attitude determination. In the attached images, I gave two axis and angles. The coefficient of the axes are the same and the angles are the same. The only difference is the vector basis. Lets say there is a rotation going from n hat to b hat. Then, you introduce a intermediate rotation s hat. So, I want to know if the DCM produced from both axis and angles will be the same or not. Does the vector basis affect the numerical value of the DCM? The DCM formula only cares about the coefficient of the axis and the angle. So, they should be the same right?arrow_forward3-15. A small fixed tube is shaped in the form of a vertical helix of radius a and helix angle y, that is, the tube always makes an angle y with the horizontal. A particle of mass m slides down the tube under the action of gravity. If there is a coefficient of friction μ between the tube and the particle, what is the steady-state speed of the particle? Let y γ 30° and assume that µ < 1/√3.arrow_forwardThe plate is moving at 0.6 mm/s when the force applied to the plate is 4mN. If the surface area of the plate in contact with the liquid is 0.5 m^2, deterimine the approximate viscosity of the liquid, assuming that the velocity distribution is linear.arrow_forward
- 3-9. Given that the force acting on a particle has the following components: Fx = −x + y, Fy = x − y + y², F₂ = 0. Solve for the potential energy V. -arrow_forward2.5 (B). A steel rod of cross-sectional area 600 mm² and a coaxial copper tube of cross-sectional area 1000 mm² are firmly attached at their ends to form a compound bar. Determine the stress in the steel and in the copper when the temperature of the bar is raised by 80°C and an axial tensile force of 60 kN is applied. For steel, E = 200 GN/m² with x = 11 x 10-6 per °C. E = 100 GN/m² with α = 16.5 × 10-6 For copper, per °C. [E.I.E.] [94.6, 3.3 MN/m².]arrow_forward3–16. A particle of mass m is embedded at a distance R from the center of a massless circular disk of radius R which can roll without slipping on the inside surface of a fixed circular cylinder of radius 3R. The disk is released with zero velocity from the position shown and rolls because of gravity, all motion taking place in the same vertical plane. Find: (a) the maximum velocity of the particle during the resulting motion; (b) the reaction force acting on the disk at the point of contact when it is at its lowest position. KAR 60° 3R M Fig. P3-16arrow_forward
- I have figured out the support reactions, Ay = 240 kN, Ax = 0 kN, Ma = 639.2 kN*m and the constant term for V(x) is 240. I am not figuring out the function of x part right. Show how to derive V(x) and M(x) for this distributed load.arrow_forward2.4 (A). A 75 mm diameter compound bar is constructed by shrinking a circular brass bush onto the outside of a 50 mm diameter solid steel rod. If the compound bar is then subjected to an axial compressive load of 160 kN determine the load carried by the steel rod and the brass bush and the compressive stress set up in each material. For steel, E 210 GN/m²; for brass, E = 100 GN/m². [I. Struct. E.] [100.3, 59.7 kN; 51.1, 24.3 MN/m².]arrow_forward1.7 (A). A bar ABCD consists of three sections: AB is 25 mm square and 50 mm long, BC is of 20 mm diameter and 40 mm long and CD is of 12 mm diameter and 50 mm long. Determine the stress set up in each section of the bar when it is subjected to an axial tensile load of 20 kN. What will be the total extension of the bar under this load? For the bar material, E = 210GN/m2. [32,63.7, 176.8 MN/mZ, 0.062mrn.l 10:41 مarrow_forward
- 2.2 (A). If the maximum stress allowed in the copper of the cable of problem 2.1 is 60 MN/m2, determine the maximum tension which C3.75 kN.1 10:41 مarrow_forward1.1 (A). A 25mm squarecross-section bar of length 300mm carries an axial compressive load of 50kN. Determine the stress set up ip the bar and its change of length when the load is applied. For the bar material E = 200 GN/m2. [80 MN/m2; 0.12mm.larrow_forward2.1 (A). A power transmission cable consists of ten copper wires each of 1.6 mm diameter surrounding three steel wires each of 3 mm diameter. Determine the combined E for the compound cable and hence determine the extension of a 30 m length of the cable when it is being laid with a tension of 2 kN. For steel, E200 GN/mZ; for copper, E = 100 GN/mZ. C151.3 GN/mZ; 9.6 mm.] 10:41 مarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Extent of Reaction; Author: LearnChemE;https://www.youtube.com/watch?v=__stMf3OLP4;License: Standard Youtube License