DeGarmo's Materials and Processes in Manufacturing
12th Edition
ISBN: 9781118987674
Author: J. T. Black, Ronald A. Kohser
Publisher: WILEY
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 31, Problem 1P
A hob that has a pitch diameter of 76.2 mm is used to cut a gear having six teeth. If a cutting speed of 27.4 m/min is used, what will be the rpm value of the gear blank?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
I will rate helpful. Thank you.
1. If a machinist wanted to drill a % inch hole in a piece of machine steel using a high speed steel
drill. At what speed in revolutions per minute should he operate the drill press?
2. Find the revolutions per minute of an 8 mm drill if it is used to cut an aluminum workpiece using
a high carbon steel drill.
3. The rpm setting of the drill press is set to 600 rpm. What is the maximum diameter in inches of a
high speed drill if it is used to drill a tool steel material?
4. A drill press has the following rpm settings; 350, 600, 1100, & 1600. What rpm setting must be
used if a 15 mm high speed steel drill is used to cut brass workpiece?
5.
A machine operator drills a hole of a 3/8 inch diameter to a stainless steel using a carbon steel
drill. He sets the drill press rpm setting to 900 rpm. Is he operating at correct setting? If not,
then what must be the correct rpm setting considering that the machine has the following rpm
settings of 300, 600, 900, 1200, and 1800?
8.)
A
gear
is turning
per
speed
edge of
?
with
second.
at
ст
a
radius of 8cm
at 1/11 radians
$
What
point
a
of the gear?
is
on
the linear
the outer
per Second?
Chapter 31 Solutions
DeGarmo's Materials and Processes in Manufacturing
Ch. 31 - How does the pitch diameter differ from the major...Ch. 31 - Prob. 2RQCh. 31 - Prob. 3RQCh. 31 - Prob. 4RQCh. 31 - Prob. 5RQCh. 31 - Explain the meaning of 14 -20 UNC-3A.Ch. 31 - Prob. 7RQCh. 31 - Prob. 8RQCh. 31 - Prob. 9RQCh. 31 - Prob. 10RQ
Ch. 31 - Prob. 11RQCh. 31 - Prob. 12RQCh. 31 - Prob. 13RQCh. 31 - What is the reason for using a taper tap before a...Ch. 31 - Prob. 15RQCh. 31 - Can a fluteless tap be used for threading a hole...Ch. 31 - What provisions should a designer make so that a...Ch. 31 - What is the major advantage of a spiral-point tap?Ch. 31 - Prob. 19RQCh. 31 - Is it desirable for a tapping fluid to have...Ch. 31 - How does thread milling differ from thread...Ch. 31 - What are the advantages of making threads by...Ch. 31 - Prob. 23RQCh. 31 - Prob. 24RQCh. 31 - What is a fluteless tap?Ch. 31 - Why is the involute form used for gear teeth?Ch. 31 - What is the diametral pitch of a gear?Ch. 31 - What is the relationship between the diametral...Ch. 31 - On a sketch of a gear, indicate the pitch circle,...Ch. 31 - What five requirements must be met for gears to...Ch. 31 - What are the advantages of helical gears compared...Ch. 31 - Prob. 32RQCh. 31 - What difficulty would be encountered in bobbing a...Ch. 31 - What is the only type of machine on which...Ch. 31 - Prob. 35RQCh. 31 - Why arent more gears made by broaching?Ch. 31 - What is the most important property of a crown...Ch. 31 - What are three basic processes for machining...Ch. 31 - Which basic gear-machining process is utilized in...Ch. 31 - When a helical gear is machined on a milling...Ch. 31 - Why is a gear-hobbing machine much more productive...Ch. 31 - Prob. 42RQCh. 31 - What are the advantages of cold-roll forming for...Ch. 31 - Prob. 44RQCh. 31 - Under what conditions should shaving not be used...Ch. 31 - Prob. 46RQCh. 31 - Can lapping be used to finish cast iron gears?Ch. 31 - What factors are usually checked in inspecting...Ch. 31 - What are the basic methods for gear finishing?Ch. 31 - A hob that has a pitch diameter of 76.2 mm is used...Ch. 31 - In Figure 31.17, a form-milling operation and...Ch. 31 - A gear-broaching machine can complete the gear in...Ch. 31 - Prob. 4PCh. 31 - If only three gears described in Problem 4 were to...Ch. 31 - Based on the size and shape of the product,...Ch. 31 - What type of engineering materials might be able...Ch. 31 - Prob. 3CS
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
3.72 Determine the resultant of the three forces acting on the horizontal beam shown.
Applied Statics and Strength of Materials (6th Edition)
What is the mass flow rate of dry air flowing at a rate of 5000 ft3/min (2.36 m3/s) where the dry bulb temperat...
Heating Ventilating and Air Conditioning: Analysis and Design
What parts are included in the vehicle chassis?
Automotive Technology: Principles, Diagnosis, And Service (6th Edition) (halderman Automotive Series)
1.1 What is the difference between an atom and a molecule? A molecule and a crystal?
Manufacturing Engineering & Technology
Determine the normal stress in each member of the truss structure. All joints are ball joint, and the material ...
Introduction To Finite Element Analysis And Design
Determine the force in each member of the truss, and state if the members are in tension or compression Set = ...
INTERNATIONAL EDITION---Engineering Mechanics: Statics, 14th edition (SI unit)
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A spur gear set is cut with a hob. The spur gears have a pressure angle of 20 degrees and a diametral pitch of 16 teeth/inch. The pinion has 32 teeth while the gear has 80. The customer wants to replace the spur gear set with a custom helical gear set. The only requirements are: (1) the same hob must be used (2) the gear set center distance must remain the same (3) the gear ratio must remain the same. The designer has decided to use a helical pinion with 28 teeth. For the helical gear set, select the proper helix angle that will guarantee the three requirements. Report your answer in degrees, 3 decimal places.arrow_forwardA twin-spindle drill simultaneously drills one ½-in hole and one ¾" through a 1" wide work piece. Both holes are twist drill with 118° point angles. cutting speed for material is 230 ft/min. The rotation speed of each spindle can be configured individually. The feed rate of both holes must be set to the same value, since both spindles go down at the same speed. The forward speed is set in such a way that the speed total metal removal does not exceed 1.50 in3 /min. Determine: a) the velocity maximum feedrate (in/min) that can be used, b) the individual feedrates (in/rev) that result in each hole and c) the time required to drill the holes.arrow_forwardWhen turning the relative speed of the work piece rotation and feed rates of the cutting tool coupled to the material to be cut must be calculated. The turning machine is designed to run at 8 different speeds via a serious of gears. The speed must be correct to ensure tool longevity, material finish and minimum time of manufacture. The cutting speed is given by the following equation Where: N = spindle speed (rpm) CS = Cutting Speed of Metal (m/min) d= Diameter of Workpiece (mm) Different metals have different CS recommendations. For this question you are considering brass which has a recommended CS of 60. The pieces to be machined range in size from 20mm to 55mm. You have been asked to determine the 8 spindle speeds given a CS value for brass for the different diameters. These speeds are to be arranged in arithmetic progression 2. geometric progressionarrow_forward
- 73 ll 6 O ... The pitch circle radius multiplied by the cosine of the pressure angle. Q3:- The increase of the contact ratio is desirable in gearing design because of:- * All of these The number of teeth will be increased in the engagement region More strength and more gear life will be achieved Smoother and faster motion None of these Q4:- To get best gearing design, it requires to:- * Increase sliding None of these Decrease slidingarrow_forwardThe number of teeth of a spur gear is 50 and it rotates at 250 rpm What will be a circular pitch and the pitch line velocity if it has a module of 5 mm?arrow_forward24 A pinion shaft of a machine transmits a torque of 60 Nm to the shaft of gear at a speed of 516 rpm, which is input at pinion gear and its shaft rotates in the clockwise direction. The number of teeth on the pinion and the gear are 36 and 84 respectively, while the module is 6 mm. Assume a pressure angle of 20°. Calculate: i) Power transmitted by the shaft of the pinion in W. ii) Torque on the shaft of the gear in Nm. iii) Speed ratio iv) Tangential load on the pinion in Narrow_forward
- Please solve it correctly , Don't Use Ai tool. (1) A twist drill bit is used to drill a hole of diameter 2.0 at 4578.1 rpm at a feed rate of 2.5 in/min. Calculate the MRR in in^3/min. Take "pi" = 3.14. Round your answer to the nearest tenth.arrow_forwardSolve first Question Only.arrow_forward4) A kiln is driven by a bull gear and pinion arrangement. There are 250 teeth on the bull gear. The pinion has 27 teeth. The pinion is driven by the low speed shaft of a 53:1 reduction reducer. A 400 hp motor turns the high speed shaft of the reducer. How fast does the motor rotate to get the kiin to rotate 4 rpm?arrow_forward
- Hello Please Answer this question, Thank you very mucharrow_forwardFind the value of the dedendum for a 20 degree full-depth involute (coarse pitch) gear with a circular pitch of 7.5 inches per tooth.arrow_forwardA 3-pitch gear is driven by a pinion whose pitch diameter is 3 inches. The pinion makes 4 turns while the gear makes 1 turn. The clearance is ⅛ inch. Find the circular pitch of the pinion, the circular pitch of the gear, the diametral pitch of the pinion, the diametral pitch of the gear, the module of the pinion, the module of the gear, the pitch diameter of the gear, the number of teeth on the pinion, the number of teeth on the gear, and the distance between centers of the shafts.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
The Most Common Metal Machining Processes (Metal Machining Video 1); Author: Sofeast Ltd;https://www.youtube.com/watch?v=uxVJ3qtezGw;License: Standard YouTube License, CC-BY
Machining process and Machine Tools; Author: Amar Gandhi;https://www.youtube.com/watch?v=X2mUJ8baaE0;License: Standard Youtube License