Automotive Technology: A Systems Approach (MindTap Course List)
6th Edition
ISBN: 9781133612315
Author: Jack Erjavec, Rob Thompson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 22, Problem 9ASRQ
While diagnosing an electronic control system: Technician A turns the ignition off before disconnecting a connector or component. Technician B uses a jumper wire to bypass a potentially faulty sensor and then observes the scan tool. Who is correct?
- Technician A
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Technician A says that some types of voltage sensors provide input to the computer by modifying or controlling a constant, predetermined voltage signal. Technician B says that a coolant temperature sensor is a voltage-generating sensor. Who is correct?
A vehicle with a direct TPMS is brought into a shop with all sensors failing to read any pressure at all. Technician A says it’s likely that all 4 sensors died at once. Technician B says it may be due to a damaged or faulty TPMS antenna. Who is correct?
Technician A
Technician B
Both Technician A and B
Neither Technician A or B
While discussing what is indicated by a vehicle’s charge indicator: Technician A says that any positive reading on an ammeter shows that the generator is in working condition. Technician B says that if the voltmeter reading does not increase immediately after starting the engine, the battery is bad. Who is correct?
Technician A
Technician B
Both A and B
Neither A nor B
Chapter 22 Solutions
Automotive Technology: A Systems Approach (MindTap Course List)
Ch. 22 - Explain the three types of memory used in the...Ch. 22 - Signals resemble a square pattern.Ch. 22 - Signals can have varying voltage levels.Ch. 22 - Means that data concerning the effects of the...Ch. 22 - The type of memory' that contains specific...Ch. 22 - A is the simplest type of semiconductor.Ch. 22 - Prob. 7RQCh. 22 - Prob. 8RQCh. 22 - How should vou test a diode with a multimeter?Ch. 22 - What is the major difference between ROM and RAM...
Ch. 22 - Which of the following is not a type of...Ch. 22 - True or False? In a high-speed CAN system, a...Ch. 22 - Which of the following is not made of...Ch. 22 - Which of the following is a basic function of a...Ch. 22 - What is the name of the module that allows the...Ch. 22 - Prob. 1ASRQCh. 22 - While checking an A/C compressor clutch coil...Ch. 22 - Technician A says that some types of voltage...Ch. 22 - Technician A says that multiplexing is a way to...Ch. 22 - Technician A says that when a diode is placed in a...Ch. 22 - Prob. 6ASRQCh. 22 - While discussing multiplex system protocols:...Ch. 22 - Prob. 8ASRQCh. 22 - While diagnosing an electronic control system:...Ch. 22 - Technician A says that based on current...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- True or False? In a high-speed CAN system, a serial data bus is used to allow communication between the various control modules in a vehicle.arrow_forwardWhen testing an engine temperature sensor: Technician A uses an ohmmeter to test the thermistor. Technician B says that the thermistor reacts to pressure and applies air pressure to the backside of the sensor. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardTrue or False? A bad ground can cause an increase in the reference voltage to a sensor.arrow_forward
- While diagnosing the control system of a BEV: Technician A begins by checking the voltage of the auxiliary battery. Technician B inspects all fuses, fusible links, wiring harness, connectors, and ground in the low-voltage circuit. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardWhile discussing diagnostic procedures: Technician A says that after the visual inspection has been performed, the DTCs should be cleared from the memory of the PCM. Technician B says that serial data can be helpful when there are no DTCs but there is a fault in the system. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardTechnician A says that some antitheft systems sound an alarm if someone enters the vehicle without a key Technician B says that some antitheft devices prevent the engine from starting. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forward
- While checking an A/C compressor clutch coil clamping diode with a DMM, the meter shows infinite resistance when the diode is measured in both directions: Technician A says that the diode is open. Technician B says that all diodes should behave this way until a specified voltage is applied to them. Who is correct? a. Technician A b. Technician B c. Both A and B d. Neither A nor Barrow_forwardWhich of the following statements about the SRS warning lamp is not true? When the ignition is first turned on, the indicator should turn on and remain on for approximately 6 seconds. If the system seems to be able to work correctly, the lamp will stay lit as the engine runs. If the lamp flashes or turns off and then turns on again, low source voltage may be indicated. A system problem is indicated when the lamp does not turn on when the ignition is initially turned on.arrow_forwardTechnician A says that based on current conditions, a reference voltage sensor modifies a fixed voltage from the computer and sends that voltage back to the computer. Technician B says that most reference voltage sensors are variable resistors or potentiometers. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forward
- Technician A says that the suspension switch must be turned off before raising any corner of a car with an electronic air suspension. Technician B says that the ignition switch must not be turned on while any corner of a car with electronic air suspension is raised. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardTechnician A uses a testlight to test circuit protection devices. Technician B uses a voltmeter to test circuit protection devices. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardWhile discussing evaporative (EVAP) systems: Technician A says that the coolant temperature has to be above a preset value before the PCM will operate the canister purge solenoid. Technician B says that the vehicle speed has to be above a preset value before the PCM will operate the canister purge solenoid. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Automotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
The Robot Revolution: The New Age of Manufacturing | Moving Upstream; Author: Wall Street Journal;https://www.youtube.com/watch?v=HX6M4QunVmA;License: Standard Youtube License