Concept explainers
Use the coefficient of volume expansion to estimate the density of water as it is heated from
The density of water.
Answer to Problem 39P
The density calculated is
The density calculated and the actual density from appendix is nearly same.
Explanation of Solution
Given information:
The water is heated from
Write the expression for the average temperature.
Here, initial temperature is
Write the expression for the density of water.
Here, the change in density is
Write the expression for temperature difference.
Here, initial temperature is
Write the expression for final density.
Write the formula for interpolation of two variables.
Here, the temperature is denoted by variables
Calculation:
Substitute
Refer to Table A-3, "Properties of saturated water" to obtain the value of
Substitute
Substitute
Substitute
Refer to Table
Refer to Table
Prepare the table for temperature and density of water.
Temperature, | Density, |
| |
Substitute
Conclusion:
The density calculated is
The density calculated and the actual density from appendix is nearly same.
Want to see more full solutions like this?
Chapter 2 Solutions
FLUID MECHANICS FUND. (LL)-W/ACCESS
- The tank of an air compressor has a volume of 2m3 and is filled with air at a temperature of 40 degrees C. If agauge pressure on the tank reads 7.5 bars,what is themass of the air in the tank?arrow_forwardFor a certain ideal gas R = 25.8 ft.lb /lb °R and k =1.09a. What are the values of cp and cv?b. What mass of this gas would occupy a volume of 15 cu ft at 75 psia and 80 °F?c. If 30 Btu are transferred to this gas at constant volume in (b), what are the resultingtemperature and pressure? include the diagramarrow_forwardA full rectangular tank is 3.1m wide, 5.6m long, and 1.9 deep contains fluid weighting 663kN. Find the following: mass of the fluid kgarrow_forward
- Answer it correctly. I need the right solution within 20-40minarrow_forwardA 3 ft high 4.653 ft diameter cylinder tank contains 0.15 slug of gas at 80°F and gauge pressure of 47 in Hg (a) what is the temperature in °C and °R and K? (b) what is the gas specific volume and density? (c) what is the absolute pressure in Psi and in kPa?arrow_forwardGlobal warming will produce rising sea levels partly due to melting ice caps and partly due to the expansion of water as average ocean temperatures rise. To get some idea of the size of this effect, calculate the change in length, Ah (in mm), of a column of water 1.5 km high for a temperature increase of 1.2 °C.Assume the column is not free to expand sideways. As a model of the ocean, that is a reasonable approximation, as only parts of the ocean very close to the surface can expand sideways onto land, and only to a limited degree. As another approximation, neglect the fact that ocean warming is not uniform with depth. Properties of water: 3 = 210 x 10 /C. c= 4186 J/kg - °C, L; = 334 kJ/kg, Le = 2256 kJ/kg Enter you answer below (to the nearest mm): Ah (in mm) = Type your answer.arrow_forward
- Consider a column of a planet's atmosphere. The planet's atmosphere is a compressible ideal gas at rest that obeys the polytropic relation Po %3D 3/2 Po 3/2 where pis pressure and pis density. Here, p, and P, are the values of pressure and density, respectively, at the planet's surface. Take z (altitude) to be positive upward with z=0 at the surface, take R to be the gas constant for the planet's atmosphere, and take g to be the downward acceleration due to gravity. a) Starting from hydrostatic balance and the polytropic relation above, derive an expression for the pressure field, p(z), in terms of the given parameters. Leave all parameters except the polytropic index as algebraic. b) Derive an expression for the density field, p(z), in terms of the given parameters. Leave all parameters except the polytropic index as algebraic. c) Derive an expression for the temperature field, T(z), in terms of the given parameters. Leave all parameters except the polytropic index as algebraic.arrow_forwardOn Mars, the atmosphere is composed mainly of carbon dioxide. The value of the gas constant for the Martian atmosphere is 192 J/kg K, and the acceleration of gravity there is 3.72 m/s?. At the average level of the Martian surface, the average temperature is 228 K, the pressure is 774 Pa, and the density is 0.01768 kg/m3. surface, the average temperature is 225 K. What are the pressure and density at this altitude? At an altitude of 1km above thearrow_forwardMention the scientific term for "the ratio of density of a given solid or liquid substance to the density of water at a specific temperature and pressure." Answer:arrow_forward
- Choose correct answer: A vessel of capacity 4 m3 contains the mass of 7 kg of Helium gas at a pressure of 197000 N/m2 and a temperature of 342 K. Find the gas constant of Helium gas in J/kgK. Gas constant, (J/kgK)arrow_forwardWhat is the density of the added fluid (in kg/m3)arrow_forwardThe figure shows a 50.-kg frictionless cylindrical piston that floats on 20 mol of compressed air at 45.°C. How far does the piston move if the temperature is increased to 600 °F? (This is an Isobaric process and the piston is at sea level under an atmospheric pressure of 101.3 kPa). The values given in the figure are: 50. Kg, 30.°C, and 10. cm.arrow_forward
- Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning