EBK MACHINE ELEMENTS IN MECHANICAL DESI
6th Edition
ISBN: 9780134451947
Author: Wang
Publisher: YUZU
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 2, Problem 17P
For Problems 14 −17, describe what is wrong with each statement.
17. “Based on the fact that this aluminum plate has a hardness of HB 150, its approximate tensile strength is 75 ksi.”
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
4. What useful informations are obtained from the tensile test of a ductile material?
5. What do you mean by factor of safety?
6. List the important factors that influence the magnitude of factor of safety.
7. What is meant by working stress and how it is calculated from the ultimate stress or yield stress of a
material? What will be the factor of safety in each case for different types of loading?
8. Describe the procedure for finding out the stresses in a composite bar.
9. Explain the difference between linear and lateral strain.
Describe the behavior of tested materials (mild steel and aluminium) as it responds to increasing load, in tensile test experiment.
Draw a Stress/Strain graph of a mild tensile steel and identify the limit of proportionality and the yield point
Chapter 2 Solutions
EBK MACHINE ELEMENTS IN MECHANICAL DESI
Ch. 2 - Define ultimate tensile strength.Ch. 2 - Define yield point.Ch. 2 - Define yield strength and tell how it is measured.Ch. 2 - What types of materials would have a yield point?Ch. 2 - What is the difference between proportional limit...Ch. 2 - Define Hooke’s law.Ch. 2 - What property of a material is a measure of its...Ch. 2 - What property of a material is a measure of its...Ch. 2 - If a material is reported to have a percent...Ch. 2 - Define Poisson’s ratio.
Ch. 2 - If a material has a tensile modulus of elasticity...Ch. 2 - A material is reported to have a Brinell hardness...Ch. 2 - A steel is reported to have a Brinell hardness of...Ch. 2 - For Problems 14 17, describe what is wrong with...Ch. 2 - For Problems 14 17, describe what is wrong with...Ch. 2 - For Problems 14 17, describe what is wrong with...Ch. 2 - For Problems 14 17, describe what is wrong with...Ch. 2 - Name two tests used to measure impact energy.Ch. 2 - Prob. 19PCh. 2 - Prob. 20PCh. 2 - Prob. 21PCh. 2 - What is the typical carbon content of a low-carbon...Ch. 2 - How much carbon does a bearing steel typically...Ch. 2 - What is the main difference between SAE 1213 steel...Ch. 2 - Name four materials that are commonly used for...Ch. 2 - Name four materials that are typically used for...Ch. 2 - Describe the properties desirable for the auger...Ch. 2 - Prob. 28PCh. 2 - Appendix 3If a shovel blade is made from SAE 1040...Ch. 2 - Describe the differences between through-hardening...Ch. 2 - Describe the process of induction hardening.Ch. 2 - Prob. 32PCh. 2 - Prob. 33PCh. 2 - Prob. 34PCh. 2 - Prob. 35PCh. 2 - Prob. 36PCh. 2 - Name three types of cast iron.Ch. 2 - Prob. 38PCh. 2 - Describe the process of making parts from powdered...Ch. 2 - Prob. 40PCh. 2 - Prob. 41PCh. 2 - Prob. 42PCh. 2 - Prob. 43PCh. 2 - Prob. 44PCh. 2 - Prob. 45PCh. 2 - Prob. 46PCh. 2 - Name three typical uses for titanium alloys.Ch. 2 - Prob. 48PCh. 2 - Prob. 49PCh. 2 - Prob. 50PCh. 2 - Describe the difference between thermosetting...Ch. 2 - Suggest a suitable plastic material for each of...Ch. 2 - Name eight factors over which the designer has...Ch. 2 - Define the term composite.Ch. 2 - Prob. 55PCh. 2 - Name four types of reinforcement fibers used for...Ch. 2 - Prob. 57PCh. 2 - Prob. 58PCh. 2 - Prob. 59PCh. 2 - For what applications are sheet-molding compounds...Ch. 2 - Prob. 61PCh. 2 - Prob. 62PCh. 2 - Prob. 63PCh. 2 - Prob. 64PCh. 2 - Prob. 65PCh. 2 - Prob. 66PCh. 2 - Prob. 67PCh. 2 - Prob. 68PCh. 2 - Discuss the advantages of composite materials...Ch. 2 - Prob. 70PCh. 2 - Prob. 71PCh. 2 - Prob. 72PCh. 2 - Prob. 73PCh. 2 - Describe the general construction of a composite...Ch. 2 - Prob. 75PCh. 2 - Prob. 76PCh. 2 - Prob. 77PCh. 2 - Prob. 78PCh. 2 - Prob. 79PCh. 2 - Prob. 80PCh. 2 - Prob. 81PCh. 2 - Prob. 82PCh. 2 - Prob. 83PCh. 2 - Problems 8290. For composites made with the given...Ch. 2 - Prob. 85PCh. 2 - Prob. 86PCh. 2 - Prob. 87PCh. 2 - Prob. 88PCh. 2 - Prob. 89PCh. 2 - Prob. 90PCh. 2 - Prob. 91PCh. 2 - Prob. 92PCh. 2 - Prob. 93PCh. 2 - Problems 94 96. For the given specification for a...Ch. 2 - Prob. 95PCh. 2 - Prob. 96PCh. 2 - Prob. 97PCh. 2 - Prob. 98PCh. 2 - Prob. 99PCh. 2 - Describe how CNTs are used in a CMNC and what...Ch. 2 - Prob. 1SPCh. 2 - Prob. 2SPCh. 2 - Prob. 3SPCh. 2 - Prob. 4SPCh. 2 - Prob. 5SPCh. 2 - Prob. 6SPCh. 2 - Name three U.S. organizations whose names are...Ch. 2 - Prob. 8SPCh. 2 - A U.S. designer specifies SAE 4140 steel for a...Ch. 2 - Prob. 10SPCh. 2 - Prob. 11SPCh. 2 - Prob. 12SPCh. 2 - Prob. 13SPCh. 2 - Prob. 14SPCh. 2 - Prob. 15SPCh. 2 - Prob. 16SPCh. 2 - Prob. 17SPCh. 2 - Prob. 18SPCh. 2 - Prob. 19SPCh. 2 - Prob. 20SPCh. 2 - Prob. 21SPCh. 2 - Prob. 22SPCh. 2 - Prob. 23SPCh. 2 - Prob. 24SPCh. 2 - Prob. 25SPCh. 2 - Prob. 26SPCh. 2 - Prob. 27SPCh. 2 - Prob. 28SPCh. 2 - Prob. 29SPCh. 2 - Prob. 30SPCh. 2 - Prob. 31SPCh. 2 - Prob. 32SPCh. 2 - Prob. 33SPCh. 2 - Prob. 34SPCh. 2 - List the six general classifications of materials...Ch. 2 - Prob. 36SPCh. 2 - Prob. 37SPCh. 2 - Prob. 38SPCh. 2 - Prob. 39SPCh. 2 - Prob. 40SP
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- outline the significant differences between rockwell and brinell hardness testarrow_forward1. Please draw a typical tensile test curve for low carbon steels and mark the four stages and list their names (use critical points on the curve to help you identify the start and end points of the four stages). 2. Show the yield, ultimate tensile strength and fracture points, as well as yield and ultimate tensile strength on the curve. 3. Please draw the load and unload curve for a stress level causing the low carbon steels to experience elastic deformation only. 4. Please draw the load and unload curve for a stress level causing the low carbon steel to experience permerment deformation, and identify both elastic and plastic strain on the drawing after unloading.arrow_forward6.Explain with the aid of diagram three different hardness tests and mention the hardness measure of stainless steel and carbon steel. 7.Mention 3 relevant Standards for the hardness testing of metals.arrow_forward
- 1- With the Vickers hardness test a 10 kg load gave for a sample of brass an indentation with diagonals having mean lengths of 0.510 mm. What is the hardness? Again, what is tensile strength of brass? 2- When a load is applied to a brass specimen in a Brinell test, an indentation of 4.10 mm is Ahimary produced. Estimate the tensile strength of the brass.arrow_forwardDescribe the fatigue tests by drawing all the necessary figures.arrow_forwardDetermine the indentation diameter of a mild steel material subjected to a Brinell hardness test with a test force of 8.1 kN using a hardened steel ball indentor of 10 mm. Take the Brinell Hardness Number as 926. Also, determine the surface area of indentation. (NOTE: Please Solve the problem in a paper and upload in the separate submission link provided and also fill the answers without the unit in the box below) i) Indentation Diameter (in mm) -- ii) Surface Area of Indentation (in mm?)arrow_forward
- The engineering stress-engineering strain tensile curve for a stainless steel type 304 alloy is shown. Calculate the constants K and n for the true stress and true strain curve before necking (or = K (&)"). Engineering Stress (MPa) 1000 900- 800- 700- 600- 500- 400- 300- 200- 100- of 0.0 02 0.4 Enginering Strain (mm/mm) 0.6 0.8 1.0arrow_forwardExplain a hardness test from Vockers, Brinnell or Rockwell. Then analyse the hardness figures of 0.9% Carbon steel and 0.15% Carbon steel and what effect these differences will have on the material properties.arrow_forwardUsing the tensile test simulation tool, a. generate the stress-strain curve for aluminum b. Indicate the following points in the stress-strain curve for aluminum and give the corresponding values: limit of proportionality elastic limit 0.2% offset yield stress (include the graph illustrating how this was determined) ultimate stress fracture stress c. Calculate modulus of elasticity. d. compare aluminum with nylon (include the related graph) and answer the following: Which has higher tensile strength? Provide the necessary values to support the answer. Which is stiffer? Support your answer with calculations.arrow_forward
- A mild steel material is subjected to a Brinell hardness test with an applied force of 7459 N using a hardened steel ball indentor of 11 mm and it is found that the Brinell Hardness Number as 954. Determine the surface area of indentation and indentation diameter. (NOTE: Please Solve the problem in a paper and upload in the separate submission link provided and also fill the answers without the unit in the box below) i) Surface Area of Indentation (in mm?) -- ( ii) Indentation Diameter (in mm)arrow_forwardAn electric car manufacturer is looking to utilize some stock AISI 8740, hot rolled steel bars that are around 2 inches in diameter for their conveyor system that is being set up to start producing their own batteries. The data sheet shows the the bars to have 132,000 psi tensile strength, 87,500 psi yield strength, and 16.7% elongation. A hardness of 262 Bhn allows it to be finish machined after heat treatment. They keep their workspace at 70°F. What is the working endurance strength, Se? 39,750 psi 28,562 psi 42,500 psi 33,400 psiarrow_forwardDo both partsarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Introduction to Ferrous and Non-Ferrous Metals.; Author: Vincent Ryan;https://www.youtube.com/watch?v=zwnblxXyERE;License: Standard Youtube License