Applied Statics and Strength of Materials (6th Edition)
6th Edition
ISBN: 9780133840544
Author: George F. Limbrunner, Craig D'Allaird, Leonard Spiegel
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 18, Problem 18.37SP
A 2-in-diameter standard-weight steel pipe is used as an axially loaded column. Calculate the allowable axial compressive load using Euler’s formula and a factor of safety of 4. The pipe column is 84 in. long and is fixed at one end and pin-connected at the other end. Assume the proportional limit = 34 ksi.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
The metallic hollow pipe shown in Figure Q1 is fixed at both its ends, and is under axial compression. The pipe has an external diameter D = 74 mm, an internal diameter d = 49 mm, and a length L = 5.06 m. The Young's Modulus of the metal used to manufacture the pipe is: E = 157.59 GPa.
Figure Q1
Calculate the critical buckling load Pcrit using Euler's Formula. Assume the critical buckling load obtained through your calculations is valid in this case, and does not require verification.
Use π = 3.14159 if needed.
Express your answer in the unit: Newton (N).
Report your answer to 2 decimal places.
Chapter 18 Solutions
Applied Statics and Strength of Materials (6th Edition)
Ch. 18 - Calculate the Euler buckling load for an axially...Ch. 18 - Calculate the Euler buckling load for a...Ch. 18 - A pin-connected axially loaded compression member...Ch. 18 - Prob. 18.4PCh. 18 - Plot a curve showing the relationship of feversus...Ch. 18 - A W1222 structural steel wide-flange section is...Ch. 18 - Prob. 18.7PCh. 18 - Calculate the allowable axial compressive load for...Ch. 18 - A W20059 structural steel wide-flange section is...Ch. 18 - Use Euler’s formula and a factor of safety of 2.5...
Ch. 18 - For Problems 18.11 through 18.17, unless otherwise...Ch. 18 - For Problems 18.11 through 18.17, unless otherwise...Ch. 18 - For Problems 18.11 through 18.17, unless otherwise...Ch. 18 - For Problems 18.11 through 18.17, unless otherwise...Ch. 18 - For Problems 18.11 through 18.17, unless otherwise...Ch. 18 - For Problems 18.11 through 18.17, unless otherwise...Ch. 18 - Prob. 18.17PCh. 18 - For Problems 18.18 through 18.21, use the...Ch. 18 - For Problems 18.18 through 18.21, use the...Ch. 18 - For Problems 18.18 through 18.21, use the...Ch. 18 - For Problems 18.18 through 18.21, use the...Ch. 18 - For Problems 18.22 through 18.26, assume normal...Ch. 18 - For Problems 18.22 through 18.26, assume normal...Ch. 18 - For Problems 18.22 through 18.26 assume normal...Ch. 18 - For Problems 18.22 through 18.26, assume normal...Ch. 18 - For Problems 18.22 through 18.26, assume normal...Ch. 18 - For the following computer problems, any...Ch. 18 - For the following computer problems, any...Ch. 18 - Calculate the Euler buckling load for an axially...Ch. 18 - 18.32 Calculate the Euler buckling load for an...Ch. 18 - 18.33 A structural steel shape of ASTM A992 steel...Ch. 18 - Calculate the Euler buckling load for a...Ch. 18 - 18.35 Rework Problem 18.34 assuming that the...Ch. 18 - 18.36 A built-up steel column is made by welding a...Ch. 18 - A 2-in-diameter standard-weight steel pipe is used...Ch. 18 - A structural steel column is 30 ft long and must...Ch. 18 - 18.39 Compute the allowable axial compressive load...Ch. 18 - 18.40 Determine the allowable axial compressive...Ch. 18 - 18.41 Using the AISC column approach, compute the...Ch. 18 - Using the AISC column equations, select the...Ch. 18 - Select the lightest extrastrong steel pipe section...Ch. 18 - 18.44 Compute the required diameter of a steel...Ch. 18 - 18.45 A 19-mm-diameter steel rod is 350 mm in...Ch. 18 - 18.46 A pin-connected linkage bar is 16 in. long...Ch. 18 - Prob. 18.47SPCh. 18 - Prob. 18.48SPCh. 18 - Prob. 18.49SPCh. 18 - Prob. 18.50SPCh. 18 - Prob. 18.51SP
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A sign for an automobile service station is supported by two aluminum poles of hollow circular cross section, as shown in the figure. The poles are being designed to resist a wind pressure of 75 lb/ft" against the full area of the sign. The dimensions of the poles and sign are hx= 20 ft, /r =5 ft, and h = 10 ft. To prevent buckling of the walls of the poles, the thickness e is specified as one-tenth the outside diameter d. (a) Determine the minimum required diameter of the poles based upon an allowable bending stress of 7500 psi in the aluminum. (b) Determine the minimum required diameter based upon an allowable shear stress of 300 psi.arrow_forwardThree round, copper alloy bars having the same length L but different shapes are shown, in the figure. The first bar has a diameter d over its entire length, the second has a diameter d over one-fifth of its length, and the third has a diameter d over one-fifteenth of its length. Elsewhere, the second and third bars have a diameter Id. All three bars are subjected to the same axial load P. Use the following numerical data: P = 1400 kN, L = 5m,d= 80 mm, E= 110 GPa. and v = 0.33. (a) Find the change in length of each bar. (b) Find the change in volume of each bar.arrow_forwardSolve Problem 11.3-3 for a W 10 × 45 steel column having a length L = 28 ft.arrow_forward
- Compare the angle of twist 1 for a thin-walled circular tube (see figure) calculated from the approximate theory for thin-walled bars with the angle of twist 2 calculated from the exact theory of torsion for circular bars, Express the ratio 12terms of the non-dimensional ratio ß = r/t. Calculate the ratio of angles of twist for ß = 5, 10, and 20. What conclusion about the accuracy of the approximate theory do you draw from these results?arrow_forwardRigid bar ACB is supported by an elastic circular strut DC having an outer diameter of 15 in. and inner diameter of 14.4 in. The strut is made of steel with a modulus elasticity of E = 29,000 ksi. Point load P = 5 kips is applied at B. Calculate the change in length of the circular strut DC. What is the vertical displacement of the rigid bar at point B?arrow_forwardAn idealized column is made up of rigid bars ABC and CD that are joined by a rotational elastic connection at C with stiffness ßR. The column has a roller support at B and a pin support at D. Find an expression for the critical load Pcr of the column.arrow_forward
- A flat bar of width b and thickness t has a hole of diameter d drilled through it (see figure). The hole may have any diameter that will fit within the bar. What is the maximum permissible tensile load Pmaxif the allowable tensile stress in the material is st?arrow_forwardA pinned-end strut of aluminum (E = 10,400 ksi) with a length L = 6 ft is constructed of circular tubing with an outside diameter d = 1 in. (sec figure). The strut must resist an axial load F = 4 kips with a factor of safety n = 2.0 with respect to the critical load. Determine the required thickness t of the tube.arrow_forwardAn aluminum pipe column (E = 10,400 ksi) with a length L = 10.0 ft has inside and outside diameters d1= 5.0 in. and d2= 6.0 in., respectively (sec figure). The column is supported only at the ends and may buckle in any direction. Calculate the critical load Pcrfor the following end conditions: (a) pinned-pinned, (b) fixed-free, (c) fixed-pinned, and (d) fixed-fixed.arrow_forward
- An idealized column is composed of rigid bars ABC and CD joined by an elastic connection with rotational stiffness ßRIat C. There is a roller support at B and an elastic support at D with translationa1 spring stiffness ß and rotational stiffness ßR2. Find the critical buckling loads for each of the two buckling modes of the column. Assume that L = 3 m, ß = 9 kN/m, and ßR]= ßR1= ßL2. Sketch the buckled mode shapes.arrow_forwardA long re Lai nine: wall is braced by wood shores set at an angle of 30° and supported by concrete thrust blocks, as shown in the first part of the figure. The shores are evenly spaced at 3 m apart. For analysis purposes, the wall and shores are idealized as shown in the second part of the figure. Note that the base of the wall and both ends of the shores are assumed to be pinned. The pressure of the soil against the wall is assumed to be triangularly distributed, and the resultant force acting on a 3-meter length of the walls is F = 190 kN. If each shore has a 150 mm X 150 mm square cross section, what is the compressive stressarrow_forwardAn idealized column consists of rigid bar ABCD with a roller support at B and a roller and spring support at D. The spring constant at D. is ß = 750 N/m. Find the critical load Pcrof the column.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
EVERYTHING on Axial Loading Normal Stress in 10 MINUTES - Mechanics of Materials; Author: Less Boring Lectures;https://www.youtube.com/watch?v=jQ-fNqZWrNg;License: Standard YouTube License, CC-BY