Applied Statics and Strength of Materials (6th Edition)
6th Edition
ISBN: 9780133840544
Author: George F. Limbrunner, Craig D'Allaird, Leonard Spiegel
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 17, Problem 17.37SP
A short 3-in.-square steel bar with a 1-in.-diameter axial hole is fixed at its base and loaded at the top as shown. Calculate the value of the force P for which the maximum combined normal stress at the fixed end will not exceed 22 ksi.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A lightweight lever consists of a 0.8m solid bar rigidly mounted to a large structure and a 0.5m solid lever
welded to the solid bar. Using the loading indicated and assuming the material has a Young's Modulus of
200 GPa and a shear modulus of 86 GPa, calculate:
(a) the maximum stress at Point A on the Cross-section a-a,
(b) the vertical displacement of the knob when the load is applied relative to Cross-section a-a.
B
C
50 mm
Section ad
a 0.8 m
0.5 m
100 N
38 mm
Focus
QUESTION 2
Consider that x = 2.76 ft and y = 7.01 ft.
B
The 5.7-in diameter steel shaft AB is attached into the rigid wall at C and supported by a smooth bearing at A. The lever AC is welded to the end of the
shaft. The maximum allowable stress for shaft AB is 355 psi.
Determine the maximum allowable force P in lbs.
C
5. Three wood boards, each 3.5 in. wide, are joined by the 3/4-in.-diameter bolt. If the working stresses for wood
are 750 psi in tension and 1450 psi in bearing, find the largest allowable value of the force P.
²
1 in.
P
2 in.
P
1 in.
T
in.
Chapter 17 Solutions
Applied Statics and Strength of Materials (6th Edition)
Ch. 17 - Prob. 17.1PCh. 17 - A horizontal 30-ft simple span beam is supported...Ch. 17 - A 1-in.-by-4-in, steel bar is subjected to the...Ch. 17 - A W410100 structural steel wide-flange section is...Ch. 17 - A W1272 structural steel wide-flange section is...Ch. 17 - A solid steel shaft 3 in. in diameter and 4 ft...Ch. 17 - A short compression member is subjected to a...Ch. 17 - With reference to Problem 17.7, calculate the...Ch. 17 - A section of a 51-mm-diameter standard-weight...Ch. 17 - For the pipe of Problem 17.9, compute the maximum...
Ch. 17 - A concrete pedestal is in the shape of a cube and...Ch. 17 - 17.12 For the pedestal of Problem 17.11, assume...Ch. 17 - 17.13 Rework Problem 17.11, but assume that the...Ch. 17 - A 12-in-square concrete pedestal is subjected to a...Ch. 17 - 17.15 A short compression member is subjected to a...Ch. 17 - A rectangular concrete footing, 4 ft by 8 ft in...Ch. 17 - The bending and shear stresses developed at a...Ch. 17 - Stresses developed at a point in a machine part...Ch. 17 - Calculate the principal stresses at points A and B...Ch. 17 - 17.20 Rework Problem 17.19 using P = 8000 lb and...Ch. 17 - 17.21 A 1-in.-square steel bar is subjected to an...Ch. 17 - 17.22 A bar having a cross-sectional area of 6...Ch. 17 - Rework Problem 17.22, changing the load to a...Ch. 17 - Solve Problem l7.17 using Mohr’s circle.Ch. 17 - For the elements shown in Problem 17.18, use...Ch. 17 - Solve Problem 17.19 using Mohr’s circle.Ch. 17 - In Problem 17.19, change the load to 8000 lb and...Ch. 17 - For the following computer problems, any...Ch. 17 - For the following computer problems, any...Ch. 17 - For the following computer problems, any...Ch. 17 - For the following computer problems, any...Ch. 17 - A 4-in.-by-8-in. (S4S) Douglas fir timber beam is...Ch. 17 - A horizontal flexural member (a girt) in the wall...Ch. 17 - A simply supported W1850 structural steel...Ch. 17 - A steel link in a machine is designed to avoid...Ch. 17 - 17.36 An 8-in-square (S4S) vertical timber post is...Ch. 17 - A short 3-in.-square steel bar with a...Ch. 17 - A timber member 150 mm by 250 mm (S4S) is loaded...Ch. 17 - A concrete wall 8 ft high and 3 ft thick is...Ch. 17 - 17.40 A short compression member is subjected to a...Ch. 17 - 17.41 Calculate the maximum eccentric load that...Ch. 17 - A short compression member is subjected to two...Ch. 17 - 17.43 Calculate the force P that may be applied to...Ch. 17 - 17.44 A load of 1000 lb is supported on a...Ch. 17 - 17.45 A short compression member is subjected to...Ch. 17 - 17.46 A structural steel wide-flange section is...Ch. 17 - 17.47 A cast-iron frame for a piece of industrial...Ch. 17 - 17.48 The assembly shown is used in a machine. It...Ch. 17 - 17.49 A 50-mm-diameter solid steel shaft is...Ch. 17 - An element of a machine member is subjected to the...Ch. 17 - 17.51 A short-span cantilever built-up beam has...Ch. 17 - Solve Problem 17.50 using Mohr’s circle.Ch. 17 - 17.53 A cantilever beam is subjected to an...Ch. 17 - A 6-in.-diameter solid shaft is subjected to a...Ch. 17 - Rework parts (b) and (c) of Example 17.7 using...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- 4.Solve it, and draw a free body diagram.arrow_forwardBE CAREFUL EVERYONE HAS GOT THIS WRONG SO FAR!!!!arrow_forwardA flanged bolt coupling consists of eight 10-mm diameter steel bolts on a bolt circle 400 mm in diamater and six 10 mm diamter steel bolts on a concentric circle 300 mm in diameter. When the shear force developed in each bolt in the outer concentric circle is 8000 N, then the stress in each bolt isarrow_forward
- The rectangular bar shown is connected to a support bracket with a 24 mm diameter pin. The width of the rectangular bar is 70 mm and its thickness is 15 mm. The bearing stress in the bar cannot exceed 120 MPa. Determine the maximum value of Pmax that can be supported based solely on consideration of the bearing stress in the bar. Note: This question is not asking about any stresses in the support bracket...just bearing stress in the rectangular bar.arrow_forward4. A load P is applied concentrically to the bar shown. If the allowable normal stress is 76 ksi, determine the maximum allowable load P. P 3.5 in. 0.5 in. dia. hole 0.4 in. rad. 2.5 in. Parrow_forwardThe internal drag truss for the wing of a light airplane is subjected to the forces shown. Determine the stress in members EF, GF and CG. The crossectional area of the truss member is a semi circle with a radius of 1.5 in.arrow_forward
- Problem #1: The following bar has a diameter of 40 mm and is subjected to the loads shown. For the point A determined: 45 N.m 300 mm 5 kN 200 mm B a. The combination of normal and shear stresses b. The maximums and minimums. Indicate the orientation of the principal axes. C. The maximum shear stress. Indicate the orientation of the axes for this effort.arrow_forward10. The homogeneous bar ABC that weighs 5000 Ib is supported by a smooth pin at C and a cable that runs from A to B around the frictionless pulley at D. If the diameter of the cable is 0.80 inch, calculate its axial stress. Answer: o = 4.90 ksi 3 ft 5ftarrow_forwardThe boom AB is made up of a hollow square 80-mm tube having a wall thickness of 2 mm. A 20-mm diameter steel cable BC and a 16-mm diameter pin at A support the boom in the position shown. The working stresses are 140 MPa for the cable, 110 MPa for the boom, and 70 MPa for shear in the pin. Neglecting the weight of the boom, determine the largest safe load W that can be applied as shown.arrow_forward
- 1. From the truss loaded as shown, determine the stress induced on each of the members BC, BD and CD. Consider each member has a cross sectional area of 1200 sq. millimeters. Consider the pulley to be frictionless. Solve the required forces using method of joint and method of sections. 10 kN 5kN 10 kN 2m ( 4m 60000 2m E 3m 2m 20kNarrow_forwardnumber 3arrow_forwardPlease answer this NEATLY, COMPLETELY, and CORRECTLY for an UPVOTE. A 2 kip/ft distributed load is applied on member AB, which is supported by a pin at A and bar BC. The connections at points A and B are shown in detail. All pins have a diameter of 0.5 in while all members have cross-sectional dimensions of 1.5 x 1 in. Determine the following:a. maximum normal stress in member BC (ksi)b. normal and shear stress in a horizontal section across member BC apart from the pin (ksi)c. shear stress in pins A and B (ksi)d. maximum bearing stress on member AB (ksi)arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Differences between Temporary Joining and Permanent Joining.; Author: Academic Gain Tutorials;https://www.youtube.com/watch?v=PTr8QZhgXyg;License: Standard Youtube License