To determine The temperature of the aluminum plate. Explanation Given: Convection heat transfer coefficient ( h ) is 25 W / m 2 ⋅ K . Total heat transfer area ( A s ) is 22 cm × 22 cm . Rate of heat dissipation from the aluminum plate is 12 W. Surrounding temperature ( T ∞ ) is 25 ° C . Calculation: Determine the total rate of heat dissipation from the aluminum plate. Q ˙ = 4 × 12 W = 48 W Determine the total heat transfer area. A s = 0.22 m × 0 .22 m = 0.0484 m 2 Determine the temperature of the aluminum plate

Fundamentals Of Thermal-fluid Sciences In Si Units

5th Edition

ISBN: 9789814720953

Author: Yunus Cengel, Robert Turner, John Cimbala

Publisher: McGraw-Hill Education

See similar textbooks

Videos

Question

Chapter 16, Problem 34P

To determine

The temperature of the aluminum plate.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 16, Problem 33P

Chapter 16, Problem 35P

Students have asked these similar questions

The link lengths and the value of 2 and offset for some fourbar crank-slide linkages are defined in Table 1. The linkage configuration and terminology are shown in Figure 1. For the rows assigned, find (a) all possible solutions for angle & and slider position d by vector loop method. (b) the transmission angle corresponding to angle 03. (Hint: Treat the vector R4 as virtual rocker) Show your work in details: vector loop, vector equations, solution procedure. Table 1 Row Link 2 Link 3 Offset Ө a 1.4 4 1 45° b 3 8 2 -30° C 5 20 -5 225° 03 slider axis B X offset Link 2 A R3 Link 3 R4 04 R2 02 R1 d Figure 1. X

4. Two links made of heat treated 6061 aluminum (Sy = 276 MPa, Sys = 160 MPa) are pinned together using a steel dowel pin (Sy = 1398 MPa, Sys = 806 MPa) as shown below. The links are to support a load P with a factor of safety of at least 2.0. Determine if the link will fail first by tearout, direct shear of the pin, bearing stress on the link, or tensile stress at section AA. (Hint: find the load P for each case and choose the case that gives the smallest load.) P 8 mm P 8 mm ¡+A 3 mm →A 10 mm P

1. For a feature other than a sphere, circularity is where: A. The axis is a straight line B. The modifier is specified with a size dimension C. All points of the surface intersected by any plane perpendicular to an axis or spine (curved line) are equidistant from that axis or spine D. All points of the surface intersected by any plane passing through a common center are equidistant from that center 2. What type of variation is limited by a circularity toler- ance zone? A. Ovality B. Tapering C. Bending D. Warping 3. How does the Rule #1 boundary affect the application of a circularity tolerance? A. The modifier must be used. B. The feature control frame must be placed next to the size dimension. C. The circularity tolerance value must be less than the limits of size tolerance. D. Circularity cannot be applied where a Rule #1 boundary exists. 4. A circularity tolerance may use a modifier. A. Ø B. F C. M D. ℗ 5. A real-world application for a circularity tolerance is: A. Assembly (i.e.,…

Chapter 16 Solutions

Fundamentals Of Thermal-fluid Sciences In Si Units

Ch. 16 - Prob. 1P Ch. 16 - Judging from its unit W/m·K, can we define thermal...Ch. 16 - Which is a better heat conductor, diamond or...Ch. 16 - How do the thermal conductivity of gases and...Ch. 16 - Why is the thermal conductivity of superinsulation...Ch. 16 - Why do we characterize the heat conduction ability...Ch. 16 - Consider an alloy of two metals whose thermal...Ch. 16 - What are the mechanisms of heat transfer? How are...Ch. 16 - Write down the expressions for the physical laws...Ch. 16 - How does heat conduction differ from convection?

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.