(a) Explanation Given information: The discharge ( Q ) of water is 1.2 m 3 / min . The velocity ( v A , v B ) of the water is 30 m / s . The distance between hinge and center of gravity G is 300 mm . The combined mass ( m p ) of the vane and plate is 20 kg . Calculation: Find the mass flow rate using the relation as follows: d m d t = ρ Q (1) Here, d m d t is mass flow rate and ρ is density of water. Substitute 1.2 m 3 / min for Q and 1000 kg / m 3 for ρ in Equation (1). d m d t = ( 1000 kg m 3 ) ( 1.2 m 3 min ) ( 1 min 60 s ) = 20 kg / s Sketch the free body diagram as shown in Figure 1. Refer to Figure 1. Find the angle θ by using impulse momentum principle as follows: Take a moment about C (b) To determine Find the reaction at C .

12th Edition

ISBN: 9781264095032

Author: BEER

Publisher: MCGRAW-HILL HIGHER EDUCATION

See similar textbooks

Concept explainers

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.

Videos

Question

Chapter 14.3, Problem 14.66P

(a)

To determine

Find the angle between the vane and plate (θ).

(b)

To determine

Find the reaction at C.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 14.3, Problem 14.65P

Chapter 14.3, Problem 14.67P

Students have asked these similar questions

How do you find these answers?

250 mm 400 mm A B C E F 250 mm PROBLEM 1.52 Each of the two vertical links CF connecting the two horizontal members AD and EG has a 10 × 40-mm uniform rectangular cross section and is made of a steel with an ultimate strength in tension of 400 MPa, while each of the pins at C and F has a 20-mm diameter and are made of a steel with an ultimate strength in shear of 150 MPa. Determine the overall factor of safety for the links CF and the pins connecting them to the horizontal members. 24 kN

50 mm 12 mm B O C OA 300 mm 450 mm E PROBLEM 1.51 Each of the steel links AB and CD is connected to a support and to member BCE by 25-mm-diameter steel pins acting in single shear. Knowing that the ultimate shearing stress is 210 MPa for the steel used in the pins and that the ultimate normal stress is 490 MPa for the steel used in the links, determine the allowable load P if an overall factor of safety of 3.0 is desired. (Note that the links are not reinforced around the pin holes.)

Chapter 14 Solutions

VECTOR MECHANIC

Ch. 14.1 - A 30-g bullet is fired with a horizontal velocity...Ch. 14.1 - Two identical 1350-kg automobiles A and B are at...Ch. 14.1 - An airline employee tosses two suitcases in rapid...Ch. 14.1 - Car A weighing 4000 lb and car B weighing 3700 lb...Ch. 14.1 - Two swimmers A and B, of weight 190 lb and 125 lb,...Ch. 14.1 - A 180-lb man and a 120-lb woman stand side by side...Ch. 14.1 - A 40-Mg boxcar A is moving in a railroad...Ch. 14.1 - Two identical cars A and B are at rest on a...Ch. 14.1 - A 20-kg base satellite deploys three...Ch. 14.1 - For the satellite system of Prob. 14.9, assuming...

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Find the angle between the vane and plate ( θ ) .

Solution Summary: The author explains how to find the angle between the vane and plate using the impulse momentum principle.