Two small disks A and B of mass 3 kg and 1.5 kg, respectively, may slide on a horizontal, frictionless surface. They are connected by a cord, 600 mm long, and spin counterclockwise about their mass center G at the rate of 10 rad/s. At t = 0, the coordinates of G are
Fig. P14.53 and P14.54
(a)
Find the velocity of A and B after the cord breaks.
Answer to Problem 14.53P
The velocity of A after the cord breaks is
The velocity of B after the cord breaks is
Explanation of Solution
Given information:
The mass
The mass
The cord length AB is
The rate of spin
The coordinates of G,
The velocity
The distance b is
Calculation:
Sketch the disk A and B as shown in Figure 1.
Refer to Figure 1.
The small disks A and B of mass
At location G,
Find the total mass (m) using the relation as follows:
Substitute
Substitute
Find the linear momentum using the relation as follows:
Substitute
Find the angular moment about G using the equation as follows:
Substitute
Find the angular moment about G using the equation as follows:
Refer problem 14.27,
Substitute
Find the kinetic energy
Refer to equation 14.29 in section 14.2A Kinetic energy of a System of particles in the textbook.
Substitute
Sketch the system as shown in Figure 2.
Write the conservation of linear momentum as follows:
Substitute
Substitute
Equate the coefficient i as follows:
Equate the coefficient j as follows:
Express the conservation of energy as follows:
Find the velocity
Substitute
Substitute
Apply the quadratic formula as follows:
Substitute 1 for a, 1.92 for b, and
Thus, the velocity of A after the cord breaks is
Find the velocity
Substitute
The velocity
Find the velocity
Thus, the velocity of B after the cord breaks is
(b)
Find the distance a from the y axis to the path of A.
Answer to Problem 14.53P
The distance a from the y axis to the path of A is
Explanation of Solution
Calculation:
Find the distance a from the y axis to the path of A using the relation:
Substitute
Substitute
Thus, the distance a from the y axis to the path of A is
Want to see more full solutions like this?
Chapter 14 Solutions
VECTOR MECHANIC
- (b) A steel 'hot rolled structural hollow section' column of length 5.75 m, has the cross-section shown in Figure Q.5(b) and supports a load of 750 kN. During service, it is subjected to axial compression loading where one end of the column is effectively restrained in position and direction (fixed) and the other is effectively held in position but not in direction (pinned). i) Given that the steel has a design strength of 275 MN/m², determine the load factor for the structural member based upon the BS5950 design approach using Datasheet Q.5(b). [11] ii) Determine the axial load that can be supported by the column using the Rankine-Gordon formula, given that the yield strength of the material is 280 MN/m² and the constant *a* is 1/30000. [6] 300 600 2-300 mm wide x 5 mm thick plates. Figure Q.5(b) L=5.75m Pinned Fixedarrow_forwardHelp ارجو مساعدتي في حل هذا السؤالarrow_forwardHelp ارجو مساعدتي في حل هذا السؤالarrow_forward
- Q2: For the following figure, find the reactions of the system. The specific weight of the plate is 500 lb/ft³arrow_forwardQ1: For the following force system, find the moments with respect to axes x, y, and zarrow_forwardQ10) Body A weighs 600 lb contact with smooth surfaces at D and E. Determine the tension in the cord and the forces acting on C on member BD, also calculate the reaction at B and F. Cable 6' 3' wwwarrow_forward
- Help ارجو مساعدتي في حل هذا السؤالarrow_forwardQ3: Find the resultant of the force system.arrow_forwardQuestion 1 A three-blade propeller of a diameter of 2 m has an activity factor AF of 200 and its ratio of static thrust coefficient to static torque coefficient is 10. The propeller's integrated lift coefficient is 0.3.arrow_forward
- (L=6847 mm, q = 5331 N/mm, M = 1408549 N.mm, and El = 8.6 x 1014 N. mm²) X A ΕΙ B L Y Marrow_forwardCalculate the maximum shear stress Tmax at the selected element within the wall (Fig. Q3) if T = 26.7 KN.m, P = 23.6 MPa, t = 2.2 mm, R = 2 m. The following choices are provided in units of MPa and rounded to three decimal places. Select one: ○ 1.2681.818 O 2. 25745.455 O 3. 17163.636 O 4. 10727.273 ○ 5.5363.636arrow_forwardIf L-719.01 mm, = 7839.63 N/m³, the normal stress σ caused by self-weight at the location of the maximum normal stress in the bar can be calculated as (Please select the correct value of σ given in Pa and rounded to three decimal places.) Select one: ○ 1. 1409.193 2. 845.516 O 3. 11273.545 ○ 4.8455.159 ○ 5.4509.418 6. 2818.386 7.5636.772arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY