Explanation Calculation: Refer to Equation 14.7 in section 14.1B in the textbook. Express the angular momentum of system of particles. The relation between the angular momentum H o and H G . H o = ∑ i = 1 n ( r i × m i v i ) (1) Here, H o is angular momentum and m i v i is collinear. Substitute ( r ¯ + r ′ i ) for r i in Equation (1). H o = ∑ i = 1 n ( ( r ¯ + r ′ i ) × m i v i ) = ∑ i = 1 n ( r ¯ × m i v i ) + ∑ i = 1 n ( r ′ i × m i v i ) = r ¯ ∑ i = 1 n ( m i v i ) + ∑ i = 1 n ( r ′ i × m i v i ) = r ¯ × m v ¯ + H G Refer to Equation 14.11 in section 14.1B in the textbook. ∑ M o = H ˙ o (2) The resultant the moment resultant about the fixed point o of the external force are equal to the rates changes of linear momentum and H ˙ o respectively

Vector Mechanics for Engineers: Statics and Dynamics

12th Edition

ISBN: 9781259977251

Author: BEER

Publisher: MCG

See similar textbooks

Concept explainers

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and af…

Videos

Question

Chapter 14.1, Problem 14.28P

To determine

Prove the relation ∑MG=HG

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 14.1, Problem 14.27P

Chapter 14.1, Problem 14.29P

Students have asked these similar questions

"11-17 The shaft shown in Figure P11-3 was designed in Problem 10-17. For the data in the row(s) assigned from Table P11-1, and the corresponding diameter of shaft found in Problem 10-17, design suitable bearings to support the load for at least 1E8 cycles at 1800 rpm. State all assumptions. (a) Using hydrodynamically lubricated bronze sleeve bearings with Ox = 15, 11d=0.75, and a clearance ratio of 0.001. ✓ ✓ cast-iron roller FIGURE P11-3 Shaft Design for Problems 11-17 b gear key assume bearings act as simple supports 11-19 The shaft shown in Figure P11-4 was designed in Problem 10-19. For the data in the row(s) assigned from Table P11-1, and the corresponding diameter of shaft found in Problem 10-19, design suitable bearings to support the load for at least 5E8 cycles at 1200 rpm. State all assumptions. (a) Using hydrodynamically lubricated bronze sleeve bearings with Oy = 40, 1/d=0.80, and a clearance ratio of 0.002 5. gear gear key FIGURE P11-4 Shaft Design for Problems 11-19 and…

For the frame below calculate the bending moment at point R. Take P=40 and note that this value is used for both the loads and the lengths of the members of the frame. 2.5P- A Q B R С 45 degrees ✗ ✗ P i 19 Кур -2P- 4PRN -P- -

Calculate the bending moment at the point D on the beam below. Take F=79 and remember that this quantity is to be used to calculate both forces and lengths. 15F 30F A с

Chapter 14 Solutions

Vector Mechanics for Engineers: Statics and Dynamics

Ch. 14.1 - A 30-g bullet is fired with a horizontal velocity...Ch. 14.1 - Two identical 1350-kg automobiles A and B are at...Ch. 14.1 - An airline employee tosses two suitcases in rapid...Ch. 14.1 - Car A weighing 4000 lb and car B weighing 3700 lb...Ch. 14.1 - Two swimmers A and B, of weight 190 lb and 125 lb,...Ch. 14.1 - A 180-lb man and a 120-lb woman stand side by side...Ch. 14.1 - A 40-Mg boxcar A is moving in a railroad...Ch. 14.1 - Two identical cars A and B are at rest on a...Ch. 14.1 - A 20-kg base satellite deploys three...Ch. 14.1 - For the satellite system of Prob. 14.9, assuming...

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Prove the relation ∑ M G = H G

Solution Summary: The author explains the relation between the angular momentum of system of particles and H_o.

Concept explainers

Videos

Prove the relation ∑MG=HG

Want to see the full answer?

Chapter 14 Solutions