The correct IUPAC name for the given compound has to be chosen from the given options. Concept Introduction: IUPAC nomenclature for alkene : There are about eight rules to be followed in giving IUPAC name for alkene. The suffix –ane has to be replaced with the suffix –ene. This is used to indicate the presence of double bond. The longest continuous chain of carbon atoms has to be chosen that contains both carbon atoms of the double bond. The parent carbon chain has to be numbered in a way so that the numbering begins at the end near to the double bond. In case if the double bond is equidistant from both ends, then numbering has to be done from the end that is closer to substituents. The position of the double bond has to be given a single number which is lower‑numbered carbon atom that is present in the double bond. Suffixes like –diene, -triene, -tetrene, and so on are used when the compound contains more than one double bond. In case of cycloalkenes which do not have any substitution, the numbering is not needed to locate the double bond because the bond is assumed to be between the carbons 1 and 2. In case if substituents are present in cycloalkene, then the double‑bonded carbon atoms are numbered 1 and 2 in a direction where the substituent gets the lower number. If the cycloalkenes contain more than one double bond, then one double bond is assigned the numbers 1 and 2 followed by the other double bond so that the lowest number possible is given.

Question

Want to see the full answer?

Answer 1

Question

Chapter 13.3, Problem 2QQ

Interpretation Introduction

Interpretation:

The correct IUPAC name for the given compound has to be chosen from the given options.

Concept Introduction:

IUPAC nomenclature for alkene: There are about eight rules to be followed in giving IUPAC name for alkene.

The suffix –ane has to be replaced with the suffix –ene. This is used to indicate the presence of double bond.

The longest continuous chain of carbon atoms has to be chosen that contains both carbon atoms of the double bond.

The parent carbon chain has to be numbered in a way so that the numbering begins at the end near to the double bond. In case if the double bond is equidistant from both ends, then numbering has to be done from the end that is closer to substituents.

The position of the double bond has to be given a single number which is lower‑numbered carbon atom that is present in the double bond.

Suffixes like –diene, -triene, -tetrene, and so on are used when the compound contains more than one double bond.

In case of cycloalkenes which do not have any substitution, the numbering is not needed to locate the double bond because the bond is assumed to be between the carbons 1 and 2.

In case if substituents are present in cycloalkene, then the double‑bonded carbon atoms are numbered 1 and 2 in a direction where the substituent gets the lower number.

If the cycloalkenes contain more than one double bond, then one double bond is assigned the numbers 1 and 2 followed by the other double bond so that the lowest number possible is given.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Students have asked these similar questions

What's the difference when drawing omega-6 and omega-3?

. Consider a base substitution mutation that occurred in a DNA sequence that resulted in a change in the encoded protein from the amino acid glutamic acid to aspartic acid. Normally the glutamic acid amino acid is located on the outside of the soluble protein but not near an active site. O-H¨ A. What type of mutation occurred? O-H B. What 2 types of chemical bonds are found in the R-groups of each amino acid? The R groups are shaded. CH2 CH2 CH2 H2N-C-COOH H2N-C-COOH 1 H Glutamic acid H Aspartic acid C. What 2 types of bonds could each R-group of each of these amino acids form with other molecules? D. Consider the chemical properties of the two amino acids and the location of the amino acid in the protein. Explain what effect this mutation will have on this protein's function and why.

engineered constructs that consist of hollow fibers are acting as synthetic capillaries, around which cells have been loaded. The cellular space around a single fiber can be modeled as if it were a Krogh tissue cylinder. Each fiber has an outside “capillary” radius of 100 µm and the “tissue” radius can be taken as 200 µm. The following values apply to the device:R0 = 20 µM/secaO2 = 1.35 µM/mmHgDO2,T = 1.67 x 10-5 cm2/secPO2,m = 4 x 10-3 cm/secInstead of blood inside the fibers, the oxygen transport and tissue consumption are being investigated by usingan aqueous solution saturated with pure oxygen. As a result, there is no mass transfer resistance in the synthetic“capillary”, only that due to the membrane itself. Rather than accounting for pO2 variations along the length ofthe fiber, use an average value in the “capillary” of 130 mmHg.Is the tissue fully oxygenated?