
Concept explainers
(a)
Find the required increased in speed at A
(a)

Answer to Problem 13.105P
The required increased in speed at point A
Explanation of Solution
Given information:
The altitude between the earth to point A
The altitude between the earth to point B
The radius of the earth (R) is
The acceleration due to gravity (g) is
Calculation:
Write the expression for the geocentric force acting on the spacecraft when it is orbiting around the earth
Here, G is the universal gravitational constant, M is the mass of the earth, and m is the mass of the space vehicle.
Write the expression for the force acting on the space vehicle on the surface of the earth due to gravity
Substitute
Substitute 9.81 m/s2 for g and
Write the expression for the centripetal force (F) acting on the spacecraft rotating around the earth at the given altitude as follows:
Here, v is the velocity of the spacecraft describing a circular path around the earth.
Write the expression for the geocentric force (F) acting on the spacecraft rotating at the given altitude around the earth as follows:
Equate equations (1) and (2).
Calculate the radius of the circular orbit described by the space vehicle around the earth at height
Substitute
Calculate the velocity of the space vehicle at point A
Substitute
Calculate the radius of the circular orbit described by the space vehicle around the earth at height
Substitute
Calculate the velocity of space vehicle at point B
Substitute
Use the principle of conservation of angular momentum states that, in the absence of external torque acting on the body, the angular momentum remains constant and no change of the momentum occurs during the entire process.
Write the expression for the principle of conservation of angular momentum as follows:
Here,
Substitute
Write the expression for the kinetic energy of the space vehicle at point A
Write the expression for the kinetic energy of the space vehicle at point B
Write the expression for the gravitational potential energy of the space vehicle at position A in the path AB
Write the expression for the gravitational potential energy of the space vehicle at position B in the path AB
Use the principle of conservation of energy states that sum of the kinetic and potential energy of a particle remains constant.
Calculate the speed of the space vehicle at positions A
Substitute
Substitute
Consider the equation (1).
Calculate the velocity of space shuttle at point A
Substitute
Calculate the increase in velocity at point A
Substitute
Calculate the increase in the velocity required at B
Substitute
Therefore, the required increased in speed at A
(b)
Find the total energy per unit mass
(b)

Answer to Problem 13.105P
The total energy per unit mass
Explanation of Solution
Given information:
The altitude between the earth to point A
The altitude between the earth to point B
The radius of the earth (R) is
The acceleration due to gravity (g) is
Calculation:
Calculate the total energy per unit mass of the vehicle to execute the transfer of space vehicle
Here, E is the total energy to execute the transfer.
Substitute
Therefore, the total energy per unit mass
Want to see more full solutions like this?
Chapter 13 Solutions
VECTOR MECH...,STAT.+DYN.(LL)-W/ACCESS
- Correct answers are written below. Detailed and correct solution only with fbd. I will upvote. 1: A 3 m alloy shaft fixed at one end has a torsional shearing stress capacity of 55 MPa. Due to improper fabrication, its cross-sectionalarea has become irregularly shaped. Its effective polar moment of inertia has become 2 x10-7 m4, and the maximum torque stress acts at 7.5 cm fromthe center of the shaft.[1]: If the shaft is to be replaced by a properly manufactured solid circular shaft that has a maximumshearing stress capacity of 70 MN/m2, what is the minimum diameter required so it can withstand the sameload? [2]: Calculate the thickness of a hollow circular shaft with the same outside diameter calculated initem [1] that can carry the same load. Limit the maximum shearing stress of the hollow circular shaft to0.09 GPa.Determine the angle of twist on the free end of the shaft. Use G = 150 x103 GPa. [3]: Use the solidcircular shaft from [1] and use the hollow circular shaft from [2].…arrow_forwardPlease can you assist me with the attached question. Many thanks.arrow_forwardPlease can you assist me with the attached question. Many thanks.arrow_forward
- Please can you assist me with the attached question. Many thanks.arrow_forwardIn using the bolt cutter shown, a worker applies two forces P to the handles. If the magnitude ofP is 500 N, determine the magnitude of the forces exerted by the cutter on the boltarrow_forwardArterioles bifurcate (i.e., split) into capillaries in the circulatory system. Blood flows at a velocity of 20 cm/s through an arteriole with a diameter of 0.20 cm. This vessel bifurcates into two vessels: one with a diameter of 0.17 cm and a blood flow velocity of 18 cm/sec, and one with a diameter of 0.15 cm. Each of these two vessels splits again. The 0.17-cm diameter vessel splits into two vessels, each with a diameter of 0.15 cm. The 0.15-cm diameter vessel splits into two vessels, each with a diameter of 0.12 cm. Determine the mass flow rate and velocity of blood in each of the four vessels at the end of the arteriole bifurcations. You may need to set up several systems, each with a different system boundary, in order to solve this problem.arrow_forward
- Suppose that a steel of eutectoid composition is cooled to 675°C (1250°F) from 760°C (1400°F) in less than 0.5 s and held at this temperature. (a) How long will it take for the austenite-topearlite reaction to go to 50% completion? To 100% completion? (b) Estimate the hardness of the alloy that has completely transformed to pearlite.arrow_forwardProblem 2: Determine the components of the reaction at point B (Please use paper sheet + FBD ,don't use chatgpt) MECHANICAL ENGGarrow_forwardARL040_AE_Kn_2of3... Dor Question 4. A two-throw crankshaft has masses distributed as shown: RAH 90 rpm A TRAV B Re Rev M₁ = 15kg; M₂ = 12kg L = 950mm; 1, 350mm; 1₁ = 600mm; 0₁ = 90°; 02=0°; r₁ = 300mm; r250mm The crankshaft is to be balanced by attaching masses at radii of 300 mm and rotating in planes 150 mm outside the planes of number one and number two cranks. Determine the magnitude and angular position of the balance masses. Answer 4.arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY





