THERMODYNAMICS (LL)-W/ACCESS >CUSTOM<
9th Edition
ISBN: 9781266657610
Author: CENGEL
Publisher: MCG CUSTOM
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 12.6, Problem 30P
Two grams of a saturated liquid are converted to a saturated vapor by being heated in a weighted piston–cylinder device arranged to maintain the pressure at 200 kPa. During the phase conversion, the volume of the system increases by 1000 cm3, 5 kJ of heat are required, and the temperature of the substance stays constant at 80°C. Estimate the saturation pressure Psat of this substance when its temperature is 100°C.
12–30 Estimate sfg of the substance in Prob. 12–29 at 80°C.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
An insulated rigid tank contains a saturated liquid-vapor mix of water initially at a pressure of 100 kPa. The
mass of the mixture is 5 kg, but only 75.6 % of the total mass is liquid. An electric resistance heater is turned
on within the tank until all the water has just vaporized. The heater power is a constant 2.2 kW. Hint: you will
not need to interpolate to find the solution to part (b).
Note: quantities shown in the figure are not necessarily to scale
(CC) BY-NC-SA Niel Crews, 2013
a) What is the volume of the container?
ww
b) How long was the heater on?
3
mº
minutes
Saturated
Refrigerant-134a
vapor
Saturated
liquid
A tank occupied by saturated liquid-vapor mixture of refrigerant-134a at 1.6 MPa. If the fraction of
the total volume occupied by vapor (Vsaturate vapor/Vtotal) is 0.92, determine quality of the mixture.
Present your result as percent. (For example, if you find 0.952, enter your result to system as 95.2)
If 10 kg of ice at 0C is added to 2 kg of steam at 100C, the temperature of resulting mixture is
Chapter 12 Solutions
THERMODYNAMICS (LL)-W/ACCESS >CUSTOM<
Ch. 12.6 - What is the difference between partial...Ch. 12.6 - Consider the function z(x, y). Plot a differential...Ch. 12.6 - Consider a function z(x, y) and its partial...Ch. 12.6 - Prob. 4PCh. 12.6 - Prob. 5PCh. 12.6 - Consider a function f(x) and its derivative df/dx....Ch. 12.6 - Conside the function z(x, y), its partial...Ch. 12.6 - Consider air at 350 K and 0.75 m3/kg. Using Eq....Ch. 12.6 - Consider air at 350 K and 0.75 m3/kg. Using Eq....Ch. 12.6 - Nitrogen gas at 800 R and 50 psia behaves as an...
Ch. 12.6 - Consider an ideal gas at 400 K and 100 kPa. As a...Ch. 12.6 - Using the equation of state P(v a) = RT, verify...Ch. 12.6 - Prove for an ideal gas that (a) the P = constant...Ch. 12.6 - Verify the validity of the last Maxwell relation...Ch. 12.6 - Verify the validity of the last Maxwell relation...Ch. 12.6 - Show how you would evaluate T, v, u, a, and g from...Ch. 12.6 - Prob. 18PCh. 12.6 - Prob. 19PCh. 12.6 - Prob. 20PCh. 12.6 - Prove that (PT)=kk1(PT)v.Ch. 12.6 - Prob. 22PCh. 12.6 - Prob. 23PCh. 12.6 - Using the Clapeyron equation, estimate the...Ch. 12.6 - Prob. 26PCh. 12.6 - Determine the hfg of refrigerant-134a at 10F on...Ch. 12.6 - Prob. 28PCh. 12.6 - Prob. 29PCh. 12.6 - Two grams of a saturated liquid are converted to a...Ch. 12.6 - Prob. 31PCh. 12.6 - Prob. 32PCh. 12.6 - Prob. 33PCh. 12.6 - Prob. 34PCh. 12.6 - Prob. 35PCh. 12.6 - Prob. 36PCh. 12.6 - Determine the change in the internal energy of...Ch. 12.6 - Prob. 38PCh. 12.6 - Determine the change in the entropy of helium, in...Ch. 12.6 - Prob. 40PCh. 12.6 - Estimate the specific heat difference cp cv for...Ch. 12.6 - Derive expressions for (a) u, (b) h, and (c) s for...Ch. 12.6 - Derive an expression for the specific heat...Ch. 12.6 - Derive an expression for the specific heat...Ch. 12.6 - Derive an expression for the isothermal...Ch. 12.6 - Prob. 46PCh. 12.6 - Show that cpcv=T(PT)V(VT)P.Ch. 12.6 - Show that the enthalpy of an ideal gas is a...Ch. 12.6 - Prob. 49PCh. 12.6 - Show that = ( P/ T)v.Ch. 12.6 - Prob. 51PCh. 12.6 - Prob. 52PCh. 12.6 - Prob. 53PCh. 12.6 - Prob. 54PCh. 12.6 - Prob. 55PCh. 12.6 - Does the Joule-Thomson coefficient of a substance...Ch. 12.6 - The pressure of a fluid always decreases during an...Ch. 12.6 - Will the temperature of helium change if it is...Ch. 12.6 - Estimate the Joule-Thomson coefficient of...Ch. 12.6 - Estimate the Joule-Thomson coefficient of...Ch. 12.6 - Prob. 61PCh. 12.6 - Steam is throttled slightly from 1 MPa and 300C....Ch. 12.6 - What is the most general equation of state for...Ch. 12.6 - Prob. 64PCh. 12.6 - Consider a gas whose equation of state is P(v a)...Ch. 12.6 - Prob. 66PCh. 12.6 - What is the enthalpy departure?Ch. 12.6 - On the generalized enthalpy departure chart, the...Ch. 12.6 - Why is the generalized enthalpy departure chart...Ch. 12.6 - What is the error involved in the (a) enthalpy and...Ch. 12.6 - Prob. 71PCh. 12.6 - Saturated water vapor at 300C is expanded while...Ch. 12.6 - Determine the enthalpy change and the entropy...Ch. 12.6 - Prob. 74PCh. 12.6 - Prob. 75PCh. 12.6 - Prob. 77PCh. 12.6 - Propane is compressed isothermally by a...Ch. 12.6 - Prob. 81PCh. 12.6 - Prob. 82RPCh. 12.6 - Starting with the relation dh = T ds + vdP, show...Ch. 12.6 - Using the cyclic relation and the first Maxwell...Ch. 12.6 - For ideal gases, the development of the...Ch. 12.6 - Show that cv=T(vT)s(PT)vandcp=T(PT)s(vT)PCh. 12.6 - Temperature and pressure may be defined as...Ch. 12.6 - For a homogeneous (single-phase) simple pure...Ch. 12.6 - For a homogeneous (single-phase) simple pure...Ch. 12.6 - Prob. 90RPCh. 12.6 - Prob. 91RPCh. 12.6 - Estimate the cpof nitrogen at 300 kPa and 400 K,...Ch. 12.6 - Prob. 93RPCh. 12.6 - Prob. 94RPCh. 12.6 - Prob. 95RPCh. 12.6 - Methane is to be adiabatically and reversibly...Ch. 12.6 - Prob. 97RPCh. 12.6 - Prob. 98RPCh. 12.6 - Prob. 99RPCh. 12.6 - An adiabatic 0.2-m3 storage tank that is initially...Ch. 12.6 - Prob. 102FEPCh. 12.6 - Consider the liquidvapor saturation curve of a...Ch. 12.6 - For a gas whose equation of state is P(v b) = RT,...Ch. 12.6 - Prob. 105FEPCh. 12.6 - Prob. 106FEP
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Hot water at 100 °C is added to 300 gm of water initially at 0 °C until the mixture is at 40 °C. The minimum mass of added hot water is * 120 gm 75 gm 60 gm 200 gmarrow_forwarduestion 4: (a) An 88-litre gas cylinder is filled with propane gas at a pressure of 1.15 MPa and 18°C. The propane is used to fuel a gas burner. After some time, the pressure and temperature are 210 kPa and 23°C respectively. Determine the mass of propane used. The molar mass of propane is 44 g/mole. (b) A piston-cylinder device filled with air at 365 kPa and 12°C, has an initial volume of 1.3 litres. The air is expanded at constant pressure to a volume of 3.6 litres and 516°C. Determine the amount of heat and work involved in this process and state whether the heat and work are into, or out of the gas.arrow_forwardThe tank contains 2kg of water at 20C, 1 atm. The tank is heated. When the tank pressure reaches 300kpa, the valve opens and steam starts escaping. Heating continues and steam continues to escape while the pressure remains constant until half of the mass escapes. At this time the tank is filled with saturated vapor at 300 kpa, and the valve closes. Question: Determine the volume of the tank and the amount of supplied heat.arrow_forward
- A piston-cylinder assembly contains a two-phase liquid-vapor mixture of water with an initial dryness fraction of 50%. The mass of the piston is 15 kg with a diameter of 10 cm. The surroundings exert a pressure of 1 atm in the piston. Heat is added to the system under the isopiestic process until the piston hits the stops. The final condition of the steam is saturated vapor. Determine the work in kW if the mass of the mixture is 22.963 kg/s.arrow_forwardthermodynamicsarrow_forwardA piston-cylinder assembly contains a two-phase liquid-vapor mixture of water with an initial dryness fraction of 50%. The mass of the piston is 15 kg with a diameter of 10 cm. The surroundings exert a pressure of 1 atm in the piston. Heat is added to the system under the isoplestic process until the piston hits the stops. The final condition of the steam is saturated vapor. Determine the work in kW if the mass of the mixture is 23.497 kg/s. For the steam table, please refer to the green book entitled " Thermodynamic Properties of Water Including Vapor, Liquid, and Solid Phases"arrow_forward
- Refrigerant-134a Saturated vapor Saturated liquid A tank occupied by saturated liquid-vapor mixture of refrigerant-134a at 1.8 MPa. If the fraction of the total volume occupied by vapor (Vsaturate Vapor/Vtotal) is 0.96, determine quality of the mixture. Present your result. nt. (For example, if you find 0.952, enter your result to system as 95.2)arrow_forwardThermodynamics Question: An insulated rigid tank is divided into two equal parts by a partition. Initially, one part contains 6 kg of an ideal gas at 800 kPa and 50 oC, and the other part is evacuated (pressure in the other part is zero). The partition is now removed, and the gas expands into the entire tank. What can be said about the final temperature of the gas? (Consider Joule’s experiment)arrow_forwardA piston-cylinder assembly contains a two-phase liquid-vapor mixture of water with an initial dryness fraction of 50%. The mass of the piston is 15 kg with a diameter of 10 cm. The surroundings exert a pressure of 1 atm in the piston. Heat is added to the system under the isopiestic process until the piston hits the stops. The final condition of the steam is saturated vapor. Determine the work in kW if the mass of the mixture is 17.521 kg/s. (PLEASE DO NOT ROUND OFF INTERMEDIATE ANSWERS, ONLY THE FINAL ANSWER IN THREE DECIMAL PLACES)arrow_forward
- On a hot summer day, you decide to make some iced tea. First, you brew 1.50 L of hot tea and leave it to steep until it has reached a temperature of Ttea = 75.0 ∘C. You then add 0.975 kg of ice taken from the freezer at a temperature of Tice = 0 ∘C. By the time the mix reaches equilibrium, all of the ice has melted. What is the final temperature Tf of the mixture? For the purposes of this problem, assume that the tea has the same thermodynamic properties as plain water. The specific heat of water is c = 4190 J/kg⋅∘C The heat of fusion of ice is Lf = 3.33×105 J/kg The density of the tea is ρ tea = 1.00 kg/Larrow_forward1. An ideal gas at a pressure of 4120 kPaa and a temperature of 25 °C is contained in a cylinder with a volume of 20 m³. A certain amount of the gas is released so that the pressure in the cylinder drops to 1730 kPaa. Expansion of the gas is isentropic. The heat capacity ratio is 1.4 and the gas constant is 0.286 kJ/kg-ºC. Determine the mass of gas remaining in the cylinder, in kg.arrow_forwardA piston-cylinder assembly contains a two-phase liquid-vapor mixture of water with an initial dryness fraction of 50%. The mass of the piston is 15 kg with a diameter of 10 cm. The surroundings exert a pressure of 1 atm in the piston. Heat is added to the system under the isopiestic process until the piston hits the stops. The final condition of the steam is saturated vapor. Determine the work in kW if the mass of the mixture is 19.95 kg/s. Only the Final answer is in 3 decimals point.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
First Law of Thermodynamics, Basic Introduction - Internal Energy, Heat and Work - Chemistry; Author: The Organic Chemistry Tutor;https://www.youtube.com/watch?v=NyOYW07-L5g;License: Standard youtube license