Foundations of Materials Science and Engineering
6th Edition
ISBN: 9781259696558
Author: SMITH
Publisher: MCG
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 12.15, Problem 80AAP
A newly developed metal-matrix composite is made for the National Aerospace plane with a matrix of the intermetallic compound titanium aluminide (Ti3Al) and continuous silicon carbide fibers. A unidirectional composite is made with the SiC continuous fibers all in one direction. If the modulus of the composite is 220 GPa and assuming isostrain conditions, what must the volume percent of SiC fibers in the composite be if ESiC = 390 GPa and
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A discontinuous fibre reinforced composite consists of 20mm long carbon fibres in a polymer matrix. The volume fraction of the
composite is 0.5, interfacial shear strength 5MPa and the critical fibre length 2.5mm. The fibre modulus is 250GPa and strain to
failure 1.5%. The matrix modulus is 3.5GPa and failure strain 10%.
Calculate the tensile strength of the composite in the fibre direction.
Answer: 3564
M2
An aligned and continuous glass fiber-reinforced epoxy composite consisting of 55 vol%
glass fibers has a cross-sectional area of 420 mm2. The composite is subjected to a
longitudinal load of 61,300 N. Calculate the magnitude of the stress on matrix phase if the
elastic moduli of the glass fiber and the epoxy are 165 GPa and 5.7 GPa, respectively.
Chapter 12 Solutions
Foundations of Materials Science and Engineering
Ch. 12.15 - Define a composite material with respect to a...Ch. 12.15 - Prob. 2KCPCh. 12.15 - What are some of the advantages of glass...Ch. 12.15 - Prob. 4KCPCh. 12.15 - Prob. 5KCPCh. 12.15 - What properties make carbon fibers important for...Ch. 12.15 - Prob. 7KCPCh. 12.15 - Prob. 8KCPCh. 12.15 - Prob. 9KCPCh. 12.15 - Prob. 10KCP
Ch. 12.15 - Prob. 11KCPCh. 12.15 - Prob. 12KCPCh. 12.15 - Prob. 13KCPCh. 12.15 - Prob. 14KCPCh. 12.15 - Prob. 15KCPCh. 12.15 - Describe the sheet-molding compound manufacturing...Ch. 12.15 - Prob. 17KCPCh. 12.15 - Prob. 18KCPCh. 12.15 - What are the basic raw materials for portland...Ch. 12.15 - What are the names, chemical formulas, and...Ch. 12.15 - List the five main ASTM types of portland cement...Ch. 12.15 - What is asphalt? Where is asphalt obtained?Ch. 12.15 - What are chemical composition ranges for asphalts?Ch. 12.15 - What does an asphalt mix consist of? What is the...Ch. 12.15 - Prob. 25KCPCh. 12.15 - What are the subrings of the annual growth rings...Ch. 12.15 - Prob. 27KCPCh. 12.15 - Prob. 28KCPCh. 12.15 - Prob. 29KCPCh. 12.15 - Prob. 30KCPCh. 12.15 - Prob. 31KCPCh. 12.15 - Prob. 32AAPCh. 12.15 - Prob. 33AAPCh. 12.15 - Prob. 34AAPCh. 12.15 - Prob. 35AAPCh. 12.15 - Prob. 36AAPCh. 12.15 - Prob. 37AAPCh. 12.15 - Prob. 38AAPCh. 12.15 - Prob. 39AAPCh. 12.15 - A unidirectional carbon fiberepoxy resin composite...Ch. 12.15 - Prob. 41AAPCh. 12.15 - Prob. 42AAPCh. 12.15 - Prob. 43AAPCh. 12.15 - Prob. 44AAPCh. 12.15 - Prob. 45AAPCh. 12.15 - If the tensile strength of the Kevlar 49 fibers is...Ch. 12.15 - Prob. 47AAPCh. 12.15 - Prob. 48AAPCh. 12.15 - Prob. 49AAPCh. 12.15 - Prob. 50AAPCh. 12.15 - Prob. 51AAPCh. 12.15 - What types of chemical reactions occur during the...Ch. 12.15 - Prob. 53AAPCh. 12.15 - Which component of portland cement hardens rapidly...Ch. 12.15 - Prob. 55AAPCh. 12.15 - Prob. 56AAPCh. 12.15 - Prob. 57AAPCh. 12.15 - Prob. 58AAPCh. 12.15 - Prob. 59AAPCh. 12.15 - Prob. 60AAPCh. 12.15 - Prob. 61AAPCh. 12.15 - Prob. 62AAPCh. 12.15 - Prob. 63AAPCh. 12.15 - Prob. 64AAPCh. 12.15 - Prob. 65AAPCh. 12.15 - Prob. 66AAPCh. 12.15 - Prob. 67AAPCh. 12.15 - Prob. 68AAPCh. 12.15 - Prob. 69AAPCh. 12.15 - What characteristics are desirable for the...Ch. 12.15 - Prob. 71AAPCh. 12.15 - Prob. 72AAPCh. 12.15 - Prob. 73AAPCh. 12.15 - Prob. 74AAPCh. 12.15 - Prob. 75AAPCh. 12.15 - Prob. 76AAPCh. 12.15 - Prob. 77AAPCh. 12.15 - Why does wood shrink much more in the transverse...Ch. 12.15 - A newly developed metal-matrix composite is made...Ch. 12.15 - Prob. 81AAPCh. 12.15 - Prob. 82AAPCh. 12.15 - Prob. 83AAPCh. 12.15 - Prob. 84AAPCh. 12.15 - Prob. 85AAPCh. 12.15 - Prob. 86AAPCh. 12.15 - Prob. 87SEPCh. 12.15 - Prob. 88SEPCh. 12.15 - Prob. 89SEPCh. 12.15 - Prob. 90SEPCh. 12.15 - Prob. 91SEPCh. 12.15 - Prob. 92SEPCh. 12.15 - (a) In Problem 12.94, if all three beams are to...Ch. 12.15 - Prob. 97SEPCh. 12.15 - Prob. 98SEPCh. 12.15 - Prob. 99SEPCh. 12.15 - Prob. 100SEPCh. 12.15 - Prob. 101SEPCh. 12.15 - Prob. 102SEPCh. 12.15 - Prob. 103SEPCh. 12.15 - Prob. 104SEPCh. 12.15 - In total hip replacement, most surgeons prefer a...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Glass fibres provide longitudinal reinforcement for a nylon material subject to tensile load. The fibre diameter is 20 μm and the volume fraction is 0.45. (Take Young’s modulus of glass fibres as 70 000 MPa and nylon as 2800 MPa)(i)Calculate the Young’s modulus of composite(ii)Determine the tensile strength in the glass fibre if the tensile strength of the composites and matrix is 14 MPa and 11.8 MPa, respectivelyarrow_forwardA discontinuous fibre reinforced composite consists of 20mm long carbon fibres in a polymer matrix. The volume fraction of the composite is 0.5, interfacial shear strength 5MPa and the critical fibre length 2.5mm. The fibre modulus is 250GPa and strain to failure 1.5%. The matrix modulus is 3.5GPa and failure strain 10%. If the ultimate fibre strength = 3500MPa, calculate the average failure stress in the composite. Answer: 2584arrow_forwardFor a glass/epoxy lamina with a 70% fiber volume fraction using the properties in the tables provided below (a) Find the ultimate tensile strength. (b) Find the minimum and critical fiber volume fractions related to (a). (c) Find the compressive strength when the matrix undergoes extension mode and when the matrix undergoes shear mode, which one controls the compressive failure? Property Axial modulus Transverse modulus Axial Poisson's ratio Transverse Poisson's ratio Shear modulus Axial tensile strength Axial compressive strength Transverse tensile strength Transverse compressive strength Shear strength Epoxy Glass Units 3.4 85 GPa 3.4 85 GPa 0.3 0.20 0.3 0.20 1.308 35.42 GPa 72 1550 MPa 102 1550 MPa 72 1550 MPa 102 1550 MPa 34 35 MPaarrow_forward
- A continuous and aligned glass fiber-reinforced composite with modulus of elasticity of 55 GPa. The volume fiber fraction is 40 and the modulus of elasticity of the fiber is 75 GPa. Calculate the volume fraction of epoxy matrix if you know the modulus of elasticity of the modulus of elasticity of the matrix is 2.5 GPa and then determine the strain that is sustained by each phase under applied stress of 27 Mpa. (assume that the cross-section area is 150 mm2)arrow_forwardQuestion 2 = 219,48 M//a = 247,3785 Pa 2.1 Consider a polymer reinforced with Spectra 1000 fibers, with a fiber volume ratio of x = 15 %. For a cross sectional area of 130 mm² and a load of 250 kg, calculate the stress in the fibers and in the matrix if the matrix material is polycarbonate. 2.2 Why are fibres capable of supporting a large portion of the tensile load in composite materials?arrow_forwardFor a continuous and aligned fiber-reinforced composite, the modulus of elasticity in the transverse direction is 4.91 GPa. If the volume fraction of fibers is 0.3 and the modulus of elasticity of matrix phase is 3.78 GPa, determine the modulus of elasticity of composite in longitudinal direction.arrow_forward
- A continuous-aligned composite lamina is to be designed to have Ec,L= 200 GPa, Ec,T = 10 Q3. GPa and o*c,L = 500 MPa. The desired failure strength of the fiber and matrix are o*f = 1000 MPa and o'm = 20 MPa. Calculate the following to design a composite lamina of desired stiffness and strength; (a) fiber and matrix volume fractions (b) fiber and matrix elastic modulus (c) load fractions of fiber-composite and matrix-composite (d) the calculated stiffness of fiber and matrix correspond closely to which type of fiber and matrix materialsarrow_forwardNonearrow_forward(b) A continuous and aligned fiber-reinforced composite is to be produced using 45 vol% of aramid fibers and 55 vol% of polycarbonate matrix. Mechanical properties of these two materials that are given in Table Q5(b): Table Q5(b): Mechanical properties of fiber and matrix Modulus of Elasticity (GPa) Tensile Strength (MPa) Aramid Fiber 131 3600 Polycarbonate 2.4 65 If the stress on the polycarbonate matrix is 35 MPa, when the aramid fibers fail, then compute the followings: (i) the longitudinal tensile strength (ii) the longitudinal modulus of elasticityarrow_forward
- can you help me answer this question and explain the steps you took to get to the answer i am stuck between B and D as the answerarrow_forwardIt is desired to produce an aligned and continuous fiber-reinforced epoxy composite having a maximum of 50% fibers. A minimum longitudinal modulus of elasticity of 55 GPa and a minimum tensile strength of 1200 MPa are required. E-glass and carbon (PAN standard modulus) fibers are the possible candidates to select. In addition, assume the stress levels on the epoxy matrix at fiber failure are 70 MPa for E-glass fiber and 30MPa for carbon fiber, respectively. Which fiber meets the design requirement? Use the properties given in the Table below to evaluate your selection. Materials Epoxy matrix E-glass Carbon Modulus of Elasticity (GPa) 3.1 72.5 230 Tensile Strength (MPa) 69 3450 4000arrow_forwardA composite sample of carbon reinforced epoxy has dimensions of 12 in x 12 in x 0.25 in and mass of 1.8 lb. The carbon fibers have a modulus of elasticity of 50(106) lb/in² and a density of 0.069 lb/in³. The epoxy matrix has modulus of elasticity of 0.61(106) lb/in² and a density of 0.042 lb/in³. What is the volume fraction of (a) the carbon fibers and (b) the epoxy matrix in the sample? Assume there are no voids in the sample. What is the predicted value for the modulus of elasticity (c) in the longitudinal direction and (d) the perpendicular to the carbon fibers?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
composite-materials; Author: Tonya Coffey;https://www.youtube.com/watch?v=Vu6ik-bcKf4;License: Standard youtube license