Concept explainers
One elevator arrangement includes the passenger car, a counterweight, and two large pulleys, as shown in Figure 11-50. Each pulley has a radius of 1.2 m and a moment of inertia of 380 kg · m2. The top pulley is driven by a motor The elevator car plus passengers has a mass of 3100 kg, and the counterweight has a mass of 2700 kg. If the motor is to accelerate the elevator car upward at 1.8 m/s2, how much torque must it generate? Hint: The two pulleys move together so you can model them as a single pulley with the sum of the moments of inertia.
Figure 11-50 problem 43
Want to see the full answer?
Check out a sample textbook solutionChapter 11 Solutions
EBK PHYSICS
Additional Science Textbook Solutions
Biology: Life on Earth (11th Edition)
Concepts of Genetics (12th Edition)
Human Physiology: An Integrated Approach (8th Edition)
Chemistry: An Introduction to General, Organic, and Biological Chemistry (13th Edition)
Microbiology with Diseases by Body System (5th Edition)
Cosmic Perspective Fundamentals
- A metal can containing condensed mushroom soup has mass 230 g, height 11.0 cm and diameter 6.38 cm. It is placed at rest on its side at the top of a 3.00-m-long incline that is at 28.0° to the horizontal and is then released to roll straight down. It reaches the bottom of the incline after 1.50 s. (a) Assuming mechanical energy conservation, calculate the moment of inertia of the can. I = kg • m2 (b) Which pieces of data, if any, are unnecessary for calculating the solution? (Select all that apply.) O the mass of the can V the height of the can O the angle of the incline O the time the can takes to reach the bottom O none of these (c) Why can't the moment of inertia be calculated from I = for the cylindrical can?arrow_forwardA metal can containing condensed mushroom soup has mass 220 g, height 10.0 cm and diameter 6.38 cm. It is placed at rest on its side at the top of a 3.00-m-long incline that is at 26.0° to the horizontal and is then released to roll straight down. It reaches the bottom of the incline after 1.50 s. (a) Assuming mechanical energy conservation, calculate the moment of inertia of the can. I = Your response differs from the correct answer by more than 10%. Double check your calculations. kg · m2 (b) Which pieces of data, if any, are unnecessary for calculating the solution? (Select all that apply.) O the mass of the can O the height of the can O the angle of the incline O the time the can takes to reach the bottom O none of these (c) Why can't the moment of inertia be calculated from I = -mr? for the cylindrical can? This answer has not been graded yet. Need Help? Read Itarrow_forwardA double radius pulley is attached to a wall by an axle of negligible friction and is initially at rest. Two vertical forces,both with magnitude F1P = F2P =19 N, are applied at the radii R1 =0.4 m and R2 =1 m as shown. Determine the kinetic energy of the pulley after it has undergone one full rotation.arrow_forward
- A 0.75 kg block is resting on a table. At the end of the table is a pulley. A 1.5 kg mass hangs over the pulley by a string tied to the block. The hanging mass is initially 0.6 m above the floor. The pulley is a solid disk with a mass of 0.25 kg and a radius of 0.025 m. The table exerts a 2.5 N frictional force on the block. The system is released from rest. How fast is the block moving when the hanging mass reaches the floor? Assume the table is long enough that the block remains on the table. Thank you for all your help!arrow_forwardAs shown below, a hollow cylinder with a mass 0.318 kg and an inner radius of 20 cm and an outer radius of 30 cm is attached to a solid cylinder with a mass 0.766 kg and a radius of 50 cm. It rotates at a rate of 16.4 rad/s about an axis through both of their centers. Find the kinetic energy of the system in J. axis 50 cm -30 cm 20 cmarrow_forwardA solid, uniform disk of radius 0.250 m and mass 55.9 kg rolls down a ramp of length 4.90 m that makes an angle of 14.0° with the horizontal. The disk starts from rest from the top of the ramp. (a) Find the speed of the disk's center of mass when it reaches the bottom of the ramp. m/s(b) Find the angular speed of the disk at the bottom of the ramp. rad/sarrow_forward
- Find the moment of cable AB about the x-axis and y-axis using the scalar method. В 6 m 100 N 40° 2 marrow_forwardTwo masses, mA = 34.0 kg and mB = 38.0 kg , are connected by a rope that hangs over a pulley (as in the figure). The pulley is a uniform cylinder of radius 0.381 m and mass 3.1 kg. Initially mA is on the ground and mB rests 2.4 m above the ground. If the system is released, use conservation of energy to determine the speed of mB just before it strikes the ground. Assume the pulley bearing is frictionless.arrow_forwardEach wheel of a 300-kg motorcycle is 61 cm in diameter and has rotational inertia 1.5 kg·m2. The cycle and its 72-kg rider are coasting at 75 km/h on flat road when they encounter a hill. if the cycle rolls up the hill with no applied power and no significant internal friction, what vertical height will it reach?arrow_forward
- A block of mass m1 = 2.40 kg and a block of mass m2 = 5.55 kg are connected by amassless string over a pulley in the shape of a solid disk having radius R = 0.250 mand mass M = 10.0 kg. The fixed, wedge-shaped ramp makes an angle of θ = 30.0°as shown in the figure. The coefficient of kinetic friction is 0.360 for both blocks.Use ∑ ? = ??, ∑ ?⃗ = ?� (a) Draw force diagrams of both blocks and of the pulley.(b) Determine the acceleration of the two blocks.(c) Determine the tensions in the string on both sides of the pulley.left of the pulleyright of the pulleyarrow_forwardThe crane shown in the figure is lifting a 177-kg crate upward with an acceleration of 4.41 m/s2. The cable from the crate passes over a solid cylindrical pulley at the top of the boom. The pulley has a mass of 195 kg. The cable is then wound onto a hollow cylindrical drum that is mounted on the deck of the crane. The mass of the drum is 215 kg, and its radius (the same as that of the pulley) is 0.768 m. The engine applies a counterclockwise torque to the drum in order to wind up the cable. What is the magnitude of this torque? Ignore the mass of the cable. Number Units Drum FEE Pulley- Boom IParrow_forwardThe crane shown in the figure is lifting a 226-kg crate upward with an acceleration of 4.52 m/s². The cable from the crate passes over a solid cylindrical pulley at the top of the boom. The pulley has a mass of 148 kg. The cable is then wound onto a hollow cylindrical drum that is mounted on the deck of the crane. The mass of the drum is 267 kg, and its radius (the same as that of the pulley) is 0.237 m. The engine applies a counterclockwise torque to the drum in order to wind up the cable. What is the magnitude of this torque? Ignore the mass of the cable. Number i Units Drum EFFI Pulley- Boomarrow_forward
- Physics for Scientists and Engineers: Foundations...PhysicsISBN:9781133939146Author:Katz, Debora M.Publisher:Cengage Learning