Materials Science And Engineering Properties
1st Edition
ISBN: 9781111988609
Author: Charles Gilmore
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Question
Chapter 10, Problem 2CQ
To determine
The ratio of volume of oxide formed to the volume of metal atoms that formed oxides for a protective oxide.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Calculate the unit cell edge length for an 57 wt% Ag- 43 wt% Pd alloy. All of the palladium is in solid solution, and the crystal structure for this alloy is FCC. Room temperature densities for Ag and Pd are 10.49 g/cm3 and 12.02 g/cm3, respectively, and their respective atomic weights are 107.87 g/mol and 106.4 g/mol. Report your answer in nanometers.
A niobium alloy is produced by introducing tungsten substitutional atoms in the BCC structure. The lattice parameter and density of the alloy is 0.3285 nm and 12.25 g/cm3, respectively. Calculate the fraction of tungsten alloys. (AW = 183.85 g/mol, ANb =92.91 g/mol).
A magnesium-lead alloy of mass 6.4 kg consists of a solid a phase that has a composition just slightly below the solubility limit
at 300°C (570°F). The magnesium-lead phase diagram is shown in Animated Figure 9.20.
(a) What mass of lead is in the alloy?
i
kg
(b) If the alloy is heated to 400°C (750°F), how much more lead may be dissolved in the a phase without exceeding the
solubility limit of this phase?
kg
Chapter 10 Solutions
Materials Science And Engineering Properties
Ch. 10 - Prob. 1CQCh. 10 - Prob. 2CQCh. 10 - Prob. 3CQCh. 10 - Prob. 4CQCh. 10 - Prob. 5CQCh. 10 - Prob. 6CQCh. 10 - Prob. 7CQCh. 10 - Prob. 8CQCh. 10 - Prob. 9CQCh. 10 - Prob. 10CQ
Ch. 10 - Prob. 11CQCh. 10 - Prob. 12CQCh. 10 - Prob. 13CQCh. 10 - Prob. 14CQCh. 10 - Prob. 15CQCh. 10 - Prob. 16CQCh. 10 - Prob. 17CQCh. 10 - Prob. 18CQCh. 10 - Prob. 19CQCh. 10 - Prob. 20CQCh. 10 - Prob. 1ETSQCh. 10 - Prob. 2ETSQCh. 10 - Prob. 3ETSQCh. 10 - Prob. 4ETSQCh. 10 - Prob. 5ETSQCh. 10 - Prob. 10.1PCh. 10 - Prob. 10.2PCh. 10 - Prob. 10.3PCh. 10 - Prob. 10.4PCh. 10 - Prob. 10.5PCh. 10 - Prob. 10.6PCh. 10 - Prob. 10.7PCh. 10 - Prob. 10.8PCh. 10 - Prob. 10.9PCh. 10 - Prob. 10.10PCh. 10 - Prob. 10.11PCh. 10 - Prob. 10.12P
Knowledge Booster
Similar questions
- For alloys of two hypothetical metals A and B, there exist an a, A-rich phase and a ß, B-rich phase. From the mass fractions of both phases for two different alloys (given below), which are at the same temperature, determine the composition of the phase boundary (or solubility limit) for the following: Fraction Fraction Alloy Composition a Phase B Phase 60 wt% A - 40 wt% B 0.59 0.41 30 wt% A - 70 wt% B 0.13 0.87 (a) a phase wt% A (b) B phase wt% Aarrow_forwardThe unit cell for MgFe2O4 (MgO-Fe2O3) has cubic symmetry with a unit cell edge length of 0.836 nm. If the density of this material is 4.52 g/cm3, compute its atomic packing factor. For this computation, you will need to use the ionic radii listed in Table Ionic Radii for Several Cations and Anions for a Coordination Number of 6.arrow_forwardNeed help with this question. Thank you :)arrow_forward
- Which one does NOT exist in the iron-carbon equilibrium phase diagram? A Graphite B) Ferrite C) Austenite (D Martensite E) Allarrow_forwardWhich material has a higher linear coefficient of thermal expansion? A Teflon B Titanium ) Medium-carbon steel D Soda lime glassarrow_forwardIn term of stability and based on standard electrode potentials, which one of the following metals can be considered relatively noble a. Zinc b. Silver C. Tin d. Leadarrow_forward
- There are some sources in materials which result in electrical resistivity, some of those sources are a. All options b. Impurity atoms c. Lattice vibration d. Lattice defects e. Disturbance in crystal latticearrow_forward2. In a copper-nickel system as shown in figure, an alloy composition of 35 wt% Ni was cooled down from the temperature of 1300°C. Sketch the expected microstructures at the point a, b, c, d and e and briefly describe the development of these microstructures in the equilibrium cooling. L. L (35 Ni) 1300 L (32 Ni) a (46 Ni) a(43 Ni) L (24 Ni) d 1200 1100 20 30 40 50 Composition (wt% Ni) Temperature (°C))arrow_forward[4] The comes from . the collision of electrons with atoms and molecules O voltage O current resistance O conductance None of the abovearrow_forward
- An oxide of Chromium is made up of 5.20g Chromium and 5.60g oxygen. What is the imperical formula of the oxide?arrow_forwardH.W3: Predict the ideal solubility of lead in bismuth at 280°C given that its melting point is 327°C and its enthalpy of fusion is 5.2 kJ mol-1, M.wt Bi=209 g/mol, M.wt Pb=209 g/mol.arrow_forward3.11 Each of the following statements describes a silicate mineral or mineral group. In each case, provide the appropriate name. a- The most common member of the amphibole group. b- The most common non ferromagnesian member of the mica family. c- The only silicate mineral made entirely of silicon and oxygen. d- A high-temperature silicate with a name that is based on its color. e-Characterized by striations. f- Originates as a product of chemical weathering.arrow_forward
arrow_back_ios
arrow_forward_ios
Recommended textbooks for you
Materials Science And Engineering PropertiesCivil EngineeringISBN:9781111988609Author:Charles GilmorePublisher:Cengage Learning
Materials Science And Engineering Properties
Civil Engineering
ISBN:9781111988609
Author:Charles Gilmore
Publisher:Cengage Learning