Materials Science And Engineering Properties
1st Edition
ISBN: 9781111988609
Author: Charles Gilmore
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Question
Chapter 10, Problem 5ETSQ
To determine
The method not used to protect low carbon steel from corrosion in contact with electrolyte.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Electrical resistivity of any given metallic wire depends upon
Which of the following conditions would lead to the fastest corrosion of a metal?
A
Large anodic area
B
В
Large cathodic areas
c) Small cathodic area
D
Equal cathodic and anodic areas
An annealed copper wire has a resistance of 2.670 at 27°C. Find the resistance at 60°C.
Select the correct response:
4 ohms
3 ohms
2.5 ohms
O2 ohms
Chapter 10 Solutions
Materials Science And Engineering Properties
Ch. 10 - Prob. 1CQCh. 10 - Prob. 2CQCh. 10 - Prob. 3CQCh. 10 - Prob. 4CQCh. 10 - Prob. 5CQCh. 10 - Prob. 6CQCh. 10 - Prob. 7CQCh. 10 - Prob. 8CQCh. 10 - Prob. 9CQCh. 10 - Prob. 10CQ
Ch. 10 - Prob. 11CQCh. 10 - Prob. 12CQCh. 10 - Prob. 13CQCh. 10 - Prob. 14CQCh. 10 - Prob. 15CQCh. 10 - Prob. 16CQCh. 10 - Prob. 17CQCh. 10 - Prob. 18CQCh. 10 - Prob. 19CQCh. 10 - Prob. 20CQCh. 10 - Prob. 1ETSQCh. 10 - Prob. 2ETSQCh. 10 - Prob. 3ETSQCh. 10 - Prob. 4ETSQCh. 10 - Prob. 5ETSQCh. 10 - Prob. 10.1PCh. 10 - Prob. 10.2PCh. 10 - Prob. 10.3PCh. 10 - Prob. 10.4PCh. 10 - Prob. 10.5PCh. 10 - Prob. 10.6PCh. 10 - Prob. 10.7PCh. 10 - Prob. 10.8PCh. 10 - Prob. 10.9PCh. 10 - Prob. 10.10PCh. 10 - Prob. 10.11PCh. 10 - Prob. 10.12P
Knowledge Booster
Similar questions
- In order to determine the polarization resistance of a carbon steel in acidic solution, a potential is applied and the current measured. We obtain the following values E - Eco (mv) -15 -10 -5 -2 0 2 5 10 15 i (mA cm-2) -8.5 -6.0 -2.6 -1.0 0 1.1 2.8 5.0 9.0 The anodic and cathodic Tafel coeffic.nts are equal to: ßa = 30 mV, Bc = 50 mV. Calculate (a) the polarization resistance at the corrosion potential and (b) the corrosion current density.arrow_forward29) Copper and nickel have an isomorphous phase diagram. Label which curve best matches the GENERAL TREND expected for the following properties (fill in the blank): Ductility (elongation): Yield Strength: Electrical resistivity: Note: you can use the same line for multiple properties if you choose. Modulus, Strength, Resistivity 3 A B C wt% Ni Niarrow_forwardwith brazing welding the temperature of filler metal * lower than 450°C and the melting of workpiece Both options are above more than 450°C but lower than the melting of workpiecearrow_forward
- In term of stability and based on standard electrode potentials, which one of the following metals can be considered relatively noble a. Zinc b. Silver C. Tin d. Leadarrow_forwardIn order to maximize the service life of an ion exchange unit, Select all that are True. *Iron, manganese, or the combination of the two should not exceed 3.0 mg/L in the water applied to the resin. *Turbidity should not exceed 1 NTU. *The water should not be prechlorinated. *Turbidity should not exceed 5 NTU.arrow_forwardAll the following statements are true for ceramics except __________________. Question 26 options: Electrical conductivity of ceramics is generally lower than metals. Most ceramics are lighter than metals but heavier than polymers. The melting point of ceramics is lower than most metals. Thermal expansion of ceramics are less than for metals.arrow_forward
- ceramics, calcination process is often necessary before sintering process. Why? (Brief scientific answer)arrow_forwardDefine (i) polymeric material. (ii) ceramic material.arrow_forwardASK YOUR TEACHER PRACTICE ANOTHER Thin strips of copper and brass of equal length are used to construct a bimetallic strip. When the strip is heated, due to the difference in the coefficient of linear expansion of the two metals, the brass strip will have a greater increase in length than the copper strip, causing them to bend into an arc with the brass on the outside of the curve. When the temperature of the bimetallic strip increases by 25.0°C, the angle subtended by the two ends of the curved strip is 30.3° and the difference in the radius of curvature of the two strips is 1.55 x 103 cm. Determine the original length of the strip. The coefficients of linear expansion of copper and brass are 17 x 10-6/°C and 19 x 10-6/°C respectively. cm Savearrow_forward
- Sulfur (S), Carbon (C), Graphite and Diamond are -considered اخترأحد الخيارات a. Metals b. Nonmetals c. Semimetalsarrow_forwardAlumina (A12O3) is a(n) _________ material.arrow_forward98) What is another name for austenitic stainless steels?A) p91 steelsB) 18-8 steelsC) p92 steelsD) o1 steelsE) h11 steels 99) which is more important for assembly than its values?A) yield strengthB) hardnessC) sizeD) elastic modulusE) wear behavior 100) which is not one of the general properties shown by almost every metal?A) satietyB) high hardness and strengthC) good wear resistanceD) good thermal conductivityE) good electrical conductivityarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Materials Science And Engineering PropertiesCivil EngineeringISBN:9781111988609Author:Charles GilmorePublisher:Cengage Learning
Construction Materials, Methods and Techniques (M...Civil EngineeringISBN:9781305086272Author:William P. Spence, Eva KultermannPublisher:Cengage Learning
Materials Science And Engineering Properties
Civil Engineering
ISBN:9781111988609
Author:Charles Gilmore
Publisher:Cengage Learning
Construction Materials, Methods and Techniques (M...
Civil Engineering
ISBN:9781305086272
Author:William P. Spence, Eva Kultermann
Publisher:Cengage Learning