Concept explainers
Videos
Describe how pressure switches are connected to start and stop (a) small motors and (b) large motors.
(a)
Explain how does the pressure switches are connected to start and stop small motors.
Answer to Problem 1SQ
The pressure switches are connected directly to start and stop small motors.
Explanation of Solution
Discussion:
In industrial applications, the pressure switches are used to sense pressure. A large variety of pressure switches are available to control the requirements of hydraulic machines or pneumatic machines.
Single-pole pressure switches are most commonly used and Two-pole pressure switches are used only for few applications.
In small motors, the pressure switches are directly connected to the load circuits when the capacities of the contact are sufficient for the load current.
Conclusion:
Thus, the pressure switches are connected directly to start and stop small motors.
(b)
Explain how does the pressure switches are connected to start and stop large motors.
Answer to Problem 1SQ
The pressure switches are connected series with motor starter and line to start and stop large motors.
Explanation of Solution
Discussion:
In industrial applications, the pressure switches are used to sense pressure. A large variety of pressure switches are available to control the requirements of hydraulic machines or pneumatic machines.
Single-pole pressure switches are most commonly used and Two-pole pressure switches are used only for few applications.
In large motors, the pressure switches alone cannot handle the load circuits safely where it must be connected in series with the motor starter coil and line such that the starter can start and stop large motors safely.
Conclusion:
Thus, the pressure switches are connected in series with motor starter and a line are to start and stop large motors.
Want to see more full solutions like this?
Chapter 10 Solutions
Electric Motor Control
- Both circuit do it multisim okk don't use guidelines will dislike okkarrow_forward"Please, the answer must be documented from a book, experience, or accurate information without using artificial intelligence." Write an Arduino program to read the status of two push buttons connected to pins 2&3 respectively and flash ON two LED's connected to pins 12&13 respectively according to the following scenario: If pin 2 is HIGH let LED 12 flash with delay of 400ms, and if pin 3 HIGH, let LED 13 flash ON with delay of 300ms.arrow_forward"Based on a source, book, or expertise in the specialized field, I need a solution to the question." Write an Arduino program code that controls the intensity of each LED (Ascending and descending) connected to pins {3, 5, 6, 9, 10, 11} successively at an array method) an interval one of one second. (Hint usearrow_forward
- "Based on a source, book, or expertise in the specialized field, I need a solution to the question." Write an Arduino program to control water tank levels, The 1st Tank level is monitored by ultrasonic sensor No.1, connected to pin Ao on the Arduino board and it's linked to a valve via port 7 to regulate the valve's opening and closing. Similarly, 2nd tank is monitored by ultrasonic sensor No.2, connected to pin A1, and linked to a valve through port 8. Follow the rules in the Table below to control valve and motor activation via port 13 with a 500 ms delay: TRIYAH UN Water level Tank Tank 1<500 (Threshold) Tank 2<300 Tank 1==500 Tank 2<300 Tank 1<500 Tank 2==300 Tank 1=500 Tank 2=300 Motor ON ON SON OFF Valve 1 ON OFF ON OFF Valve 2 ON ON OFF OFFarrow_forward"Based on a source, book, or expertise in the specialized field, I need a solution to the question." 1985 Write an Arduino program to flash flash three LED's connected to pins (7, 9 & 11) respectively as shown in figure below: (Note: T₁-T3-5s & T₂=3s) LED₁ (pin 7) LED2 (pin 9) LED3 (pin 11) T₁ T2 T3 1406arrow_forward"Based on a source, book, or expertise in the specialized field, I need a solution to the question." Write an Arduino programming code that activates eight LEDs connected to pins 0 to 7 successively with an interval of 1 second when switch S₁ connected to pins 8 is turned ON, and all LEDs are activated when switch S₂ connected to pins 9 is turned off. (Hint: use array method).arrow_forward
- Determine X(w) for the given function shown in Figure (1) by applying the differentiation property of the Fourier Transform. 1 x(t) Figure (1) -1 1 2arrow_forward5. Determine an expression for vo as a function of vs in the circuit shown below. Assume the operational amplifier is ideal (10 pts) 162 + + 212 10052} -j 100-52 Noarrow_forward4. A 120 volt rms voltage source supplies 20 Amps rms to a load. The load requires 2,078 watts. What is the reactive power (Vars) and the power factor of the load. Assume the load is inductive. (15pts)arrow_forward
