Concept explainers
1-111 In the hospital, your doctor orders 100. mg of medication per hour. The label on the IV bag reads 5.0 g/1000. mL.
(a) How many mL should infuse each hour?
(b) The IV administration set delivers 15 gtts/mL, where the unit gtts denotes drops of liquid as explained in Problem 1-5 1. The current drip rate is set to 10. gtts/min. Is this correct? If not, what is the correct drip rate?
(a)
Interpretation:
The amount of the medication in millilitre which is infused every hour should be identified.
Concept Introduction:
The relation between gram and milligram is as-
1 g= 1000 mg.
Answer to Problem 1.111P
To administer 100.0 mg the volume of the liquid required, is 20 mL.
Explanation of Solution
Medication ordered by the doctor = 100.00 mg per hour.
The label of the Intravenous fluid reads = 5.0g/1000.mL.
1 g = 1000 mg.
5.0 g or 5000 mg is present in 1000 mL.
1 mg is present in.
1 mL has 0.2 mL.
To administer 100.0 mg the volume of the liquid required,
To administer 100.0 mg the volume of the liquid required, is 20 mL.
(b)
Interpretation:
The flow rate of the Intravenous fluid is to be calculated along with whether the drop rate is correct or incorrect, if not the correct drop rate should be identified.
Concept Introduction:
There is a specific rate by which the Intravenous fluid is given to the patients. This specific rate can be calculated as-
Answer to Problem 1.111P
The correct drip rate is 5 gtts per minute.
Explanation of Solution
There is a specific rate by which the Intravenous fluid is given to the patients. This specific rate can be calculated as-
This is incorrect because this exceeds the required medicine as ordered by the doctor.
The correct rate is as-
The correct drip rate is 5 gtts per minute.
Want to see more full solutions like this?
Chapter 1 Solutions
Introduction to General, Organic and Biochemistry
- 1-51 A nurse practitioner orders isotonic sodium lactate 50. mL/kg body mass to be administered intravenously for a 139-lb patient with severe acidosis. The rate of flow is 150 gtts/min, and the IV administration set delivers 20. gtts/mL, where the unit “gtts” stands for drops of liquid. What is the running time in minutes?arrow_forward1-85 In Japan, high-speed “bullet trains” move with an average speed of 220. km./h. If Dallas and Los Angeles were connected by such a train, how long would it take to travel nonstop between these cities (a distance of 1490. miles)?arrow_forward1-76 If the density of air is 1.25 10-3 g/cc, what is the mass in kilograms of the air in a room that is 5.3 m long, 4.2 m wide, and 2.0 m high?arrow_forward
- 1-50 If an IV is mixed so that each 150 mL contains 500. mg of the drug lidocaine, how many minutes will it take for 750 mg of lidocaine to be administered if the rate is set at 5 mL/min?arrow_forward1-61 The density of dichloromethane, a liquid insoluble in water, is 1.33 g/cc. If dichioromethane and water are placed in a separatory funnel, which will be the upper layer?arrow_forward1-43 The speed limit in some European cities is 80 km/h. How many miles per hour is this?arrow_forward
- Molecular distances are usually given in nanometers (1 nm = 1 109 m) or in picometers (1 pm = 1 1012 m). However, the angstrom () unit is sometimes used, where 1 = 1 1010 m. (The angstrom unit is not an SI unit.) If the distances between the Pt atom and the N atom in the cancer chemotherapy drug cisplatin is 1.97 , What is this distances in nanometers? In picometers?arrow_forward1-55 Does the chemical nature of a substance change when it melts from a solid to a liquid?arrow_forward1-86 The specific heats of some elements at 25oC are as follows: aluminum = 0.215 cal/g · oC; carbon (graphite) = 0.170 caI/g oC; iron = 0.107 cal/g mercury = 0.033 1 caI/g oC. (a) Which element would require the smallest amount of heat to raise the temperature of 100 g of the element by 10oC? (b) If the same amount of heat needed to raise the temperature of 1 g of aluminum by 25oC were applied to 1 g of mercury, by how many degrees would its temperature be raised? (c) If a certain amount of heat is used to raise the temperature of 1.6 g of iron by 10oC, the temperature of 1 g of which element would also be raised by 10oC, using the same amount of heat?arrow_forward
- 1-65 While you drive your car, your battery is being charged. How would you describe this process in terms of kinetic and potential energy?arrow_forward1-68 The specific heat of steam is 0.48 cal/g oC. How many kilocalories are needed to raise the temperature of 10.5 kg of steam from 120oC to 150oC?arrow_forward1-67 If 168 g of an unknown liquid requires 2750 cal of heat to raise its temperature from 26oC to 74oC, what is the specific heat of the liquid?arrow_forward
- Introduction to General, Organic and BiochemistryChemistryISBN:9781285869759Author:Frederick A. Bettelheim, William H. Brown, Mary K. Campbell, Shawn O. Farrell, Omar TorresPublisher:Cengage LearningChemistry & Chemical ReactivityChemistryISBN:9781337399074Author:John C. Kotz, Paul M. Treichel, John Townsend, David TreichelPublisher:Cengage LearningChemistry & Chemical ReactivityChemistryISBN:9781133949640Author:John C. Kotz, Paul M. Treichel, John Townsend, David TreichelPublisher:Cengage Learning
- Chemistry: The Molecular ScienceChemistryISBN:9781285199047Author:John W. Moore, Conrad L. StanitskiPublisher:Cengage LearningGeneral Chemistry - Standalone book (MindTap Cour...ChemistryISBN:9781305580343Author:Steven D. Gammon, Ebbing, Darrell Ebbing, Steven D., Darrell; Gammon, Darrell Ebbing; Steven D. Gammon, Darrell D.; Gammon, Ebbing; Steven D. Gammon; DarrellPublisher:Cengage Learning