Q-89A turbine runner has an exit velocity of 10 m/sec. The loss due to frictionand other causes in the draft tube should not exceed 2.0 m. What maximumheight of setting will you recommend for the turbine if the cavitation is to beavoided. The velocity of water at out let of draft tube is 2 m/sec and cavitationcommences when the pressure is 2.5 m of water absolute.

Answered: Image /qna-images/answer/c89ee64e-210a-4b50-90bb-13f22f998dee.jpg

Answered: you recommend for the turbine of water…

Engineering

Civil Engineering

you recommend for the turbine of water at out let of draft tube pressure is ? 5 m of water abs

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

ori (P=880 kJ /m ) Flow under head 30 min PrPe (L= 3000 m , D= o3 m) becanse of Cooling Viscosity a long the Pipo length Will Chanfe and equal to 0.s la s for I Soo m and . of PiPe Prove that the flow is laminar and find the f low ra te . %3D 14Pa.s for the Yemain length
5.61 If viscosity is neglected, typical pump-flow results are shown in Fig. P5.61 for a model pump tested in water. The pressure rise decreases and the power required increases with the dimensionless flow coef-ficient. Curve-fit expressions are given for the data. Suppose a similar pump of 12-cm diameter is built to move gasoline at 20°C and a flow rate of 25 m³/h. If the pump rotation speed is 30 1/s, find (a) the pressure rise and (b) the power required.
orI (P=880 k9 /m ) Flow under head 3o min Pr Pe (L= 3000 m of Cooling Viscosity a long the PiPo length Will Chanje and equal to o.s Pa-s for ISoo m and 1. 14Pa.s for the Yemain length of PiPe Prove tha t the flow is laminar and find the f low ra te . , D= 0- 3 m) becanse %3D
The pipe fitting below (a wye fitting) splits Q₁ into two equal flows (Q2 = Q3). The flow entering this fitting 4 ft³/s and has a pressure of 20 psig. Neglecting losses, compute the pressures at P2 and P3. 4-inches 3-inches 3 45° 6-inches
5. ol with sp. gr. of 0.88 is being pumped frem a lower reservolr to an elevated tank The pump In the system is 65% efflelent and Is rated at 160kW. Determine the flow rate of the oll in the pipe if the total head los (rom point 1 to point 2 is 5.5m of oll. 150m 200-mm Pump Elev 160m Elev. 150 m
Please include all assumptions
Q-The allowable net positive suction head (NPSH) for a pump provided by the manufacturer for a flow of 0.05 m³/s is 3.3m. The temperature of water is 30°C (vapour pressure head absolute = 0.44 m), atmospheric pressure is 100 kPa absolute and the head loss from the reservoir to pump is 0.3 N-m/N. Find the maximum height of the pump above the suction reservoir.
Q-5
ASAP dont round off initial vlues, round off final ans only pls
Quick please
Q2. Correct the false statement. 3) For Prandtl fan, low between two expansion waves is uniform. 4) Nozzle is under-expanded when, pexit > Pback-
A 30cm pipe is connected by a reducer to a 10cm pipe. Points 1 and 2 are along the same elevation. The pressure at 1 is 200kpa. The flow is 30 L/s and energy lost between 1 and 2 is equivalent to 20kpa. Compute the pressure at 2 if the liquid flowing is water.