...2ELEVATION 20mELEVATION30mAIR P ?SG-0-84Oil flows from a tank through a 150mm diameter pipe and then discharges into air as shown. If the head loss from point 1 to point 2is 600mm, determine the pressure needed at point 1 to cause 17L/s to flow (SG of oil = 0.84)A) 93.30 KPaB) 82.19 KPa(c) 87.74 KPaD98.23 KPa76.49 KPa

Answered: Image /qna-images/answer/3ec7f3dc-2eda-4519-be52-11488037096f.jpg

2) ELEVATION 20oM ELEVATION 30m AIR Po? 150mmøØ SG 0-84 il flows from a tank through a 150mm diameter pipe and then discharges into air as shown. If the head loss from point 1 to point 2 600mm, determine the pressure needed at point 1 to cause 17L/s to flow (SG of oil = 0.84) A) 93.30 KPa B. 82.19 KPa 87.74 KPa 98.23 KPa 76.49 KPa

2) ELEVATION 20oM ELEVATION 30m AIR Po? 150mmøØ SG 0-84 il flows from a tank through a 150mm diameter pipe and then discharges into air as shown. If the head loss from point 1 to point 2 600mm, determine the pressure needed at point 1 to cause 17L/s to flow (SG of oil = 0.84) A) 93.30 KPa B. 82.19 KPa 87.74 KPa 98.23 KPa 76.49 KPa

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the resultant force of the water acting on the circular glass plate that Is to the side panel of the tank. Also, determine the location of the center of pressure along this inclined side, measured from the top. Question 2: FYw.h.A ate Fv= Yw.V 3 m radie 9810 Ixr x gate 9810 1 m 2 m Ma:0 Nar3- Fn 号×3-fvx3- -0 Ma=0-) NBx3- F t /2Fy-0 120° 3 m 1,- I,
Fluid Mechanics As shown in figure below, determine the pressure at point A
Šubiect No. Bubject Date No. An open manometer, shown în the Dright figure, is in stalled to measure D pressure in a pipe canrying (sp.gr=0.82). If the manometer liquid is carbon tetra chlovide (sp.gr=lo6o) determine the pipe pressure (in meters oil of water- colunn heig ht) an oil 11 Air > 66 Cm imanometer liquid
Oil of SG 0.75 flows through the nozzle shown and deflects the mercury in the U-tube gage. What is the pressure at B in Kpa? A 2.75 D h B C Hg(13.6)
mater 2
Glycerin of SG 1.26 flows through the nozzle shown and deflects the mercury in the U-tube gage. What is the pressure at B in kPa? A 2.75 h B Hg(13.6)
IL. Q2-1 [5 Points]:A fluid has an absolute viscosity of 0.048 Pa-s and a specific gravity of 0.913. For flow of such a fluid over a solid flat surface, the velocity at a point 50 mm away from the surface is 1.467 m/s. Calculate the shear stresses at the solid boundary (N/m) 0.67 1.2 3.35 0.97 1.41 3.03 1.35 1.79
EN.3060 - Transport Phet Consider the system shown below in which a rod is contained within a coaxial cylinder. The system is aligned vertically. The rod has a radius Ri and the outer cylinder has a radius of R2. The region between the rod and outer cylinder contains an incompressible Newtonian liquid that has a density p and viscosity u. The rod is being moved in the positive z-direction at a constant velocity V while the outer cylinder is stationary. Assume the liquid is in steady fully developed laminar flow and there is no pressure gradient acting on the liquid in the direction in which the rod is moving. (a) Write the simplified forms of the Continuity and Navier-Stokes Equations in cylindrical coordinates that will be used for solving for the velocity profile in the liquid. (b) Write the applicable boundary conditions that will be used to solve for the velocity profile. (c) Solve for the velocity profile v in terms of r, R1, R2, V, p, g and u. (d) Assume the rod has a radius RI=3…
oll, s = 0.80 kerosene,s = 0.82 A manomoter is used to moasuro tho s = 0.0012 pressure of air in shown. Solve the pressure at point A given the following hoights: the pipe as Air = 0.35 m,h2 = 0.38 m, h, = 0.20 m, %3D h4 = 0.50 m, hs = 0.10 m, h6 = 0.30 m hz hy h3 ho Water Mercury Mercury
If you could help me with parts a-d id greatly appreciate it, I will rate immediately. Thank you.
1. [Ch4 – 2] A hydraulic oil with the absolute viscosity of 0.09 N.s/m² and specific gravity of 0.9, is flowing in a 30-mm- diameter pipe at a velocity of 6 m/'s, detemine: a. The Reynolds number? Is the flow laminar or turbulent? b. The head loss due to friction in units of bars for a 100-m length of smooth pipe. 2. [Ch4 - 2] The kinematic viscosity of a hydraulic oil is 0.0001 m/s. If it is flowing in a 20-mm- diameter commercial steel pipe, find the friction factor for: a. The velocity of 5 m/s b. The velocity of 50 m/s
Crude oil (with specific weight γoil = 55 lb/ft3 ) is pumped at a rate of 400 gallons per minute from a test separator at A to the stock tank shown using a pipe that has a diameter of 4 inches. The pressure at A (to the left of the pump or prior to the pump) is 4 psi and the stock tank is open to the atmosphere. The friction head loss along the entire length of the pipe from A to B is 45 inches. Note that 1ft3 = 7.48 gallons. (a) Determine the velocity in the pipe. (b) Determine the head gain, ℎ??, delivered by the pump to the flow. (c) Determine the power required to run the pump if it is 90% efficient.