circular orifice of 50 mm diameter is fixed to the end of a water pipe of 75 mm diameter. The gauge pressure in the pipe is 70 kPa. The flow out of the orifice was measured as 0.017 m^3/second. The actual jet velocity was measured by pitot tube with a value of 12 m/s. a. Determine Cv, Cc and Cd. b. Calculate the head loss.

Q: PROBLEM 04: The fluid in the figure is water, with the surface 20m above the datum. The pipe is 15cm…

A: we will use bernoulli equation.

Q: Determine the pressure at the center of the pipe from the piezometer shown. 200mm WATER 75mmØPIPE

A: Given:- a piezo meter is attached to the pipe as shosn below

Q: An 8 in diameter (f=0.028) 500 ft long discharge a 3 in diameter water jet into the atmosphere at a…

A: Using the continuity equation calculating the jet velocity: AV=AjVj…

Q: Figure Q4 shows there are two sections of pipes in the system, which are 38m long of 5 cm diameter…

A: Given, L1 = 38 m  L2 = 45 m D1 = 5 cm or 0.05 m D2 = 15 cm or 0.15 m \ Q = 0.005 m3/s

Q: A liquid having specific gravity of 2.0 is flowing in a 50mm diameter piper. The total head at a…

A: A liquid which having some specific gravity is given in the question which is flowing through a pipe…

Q: An orifice of 0.1-meter-diameter is installed in a pipe having a diameter equal to 0.3 meters as…

A:

Q: er of

A: According to given data Pipe length = 170 m Diameter = 0.42 m Coefficient of roughness C=…

Q: PROBLEM 01: Given the figure below, (a) determine the value of h in the siphon shown if velocity at…

A: step 1-

Q: Problem 4: Water flows inside a system made of two pipe sections with diameter D =1.5 fi and D, =0.5…

A: Given data - D1 = 1.5 ft , D2 = 0.5 ft. The manometer reading are h1= 0.75 ft and h2 = 0.25 ft.…

Q: Refer to the illustration below. A C B D Solve for the following: 1. Headloss in meters at Pipe A 2.…

A:

Q: The pressure at point 2 shown in Figure is not to fall below 4.14 Bar when the flowrate from the…

A:

Q: Two pipes A & B carries an oil of specific gravities 0.9 & 1.2 respectively. The center of the pipe…

A: Specific gravity of oil in pipe A (S1) = 0.9Specific gravity of oil in pipe B S2 = 1.2Difference in…

Q: A

A:

Q: A liquid whose specific gravity is 2.0, is flowing in a 150mm diameter pipe. The total head at a…

A:

Q: Q.2.8 MASS FLOW AT A PIPE JUNCTION Consider the s. tv low in a water pipc joint shown in the…

A:

Q: Water flows through a pipe at 5 L/s as shown. If the gage pressure of 12.5 kPa, 11.5 kPa and 10.3…

A:

Q: Water flows from the tank shown in the figure below. At a depth of 1.5 ft the rate of change of…

A:

Q: At two points 1 and 2 in a pipeline the velocities are Vand 2V, respectively. Both the points are at…

A: given data : velocity at point 1= V velocity at point 2= 2V

Q: Orifice meter with orifis cross-section 0.00785 m2 is inserted in a pipe of cross-section 0.0314 m2.…

A: Given: Orifice cross-section, A1 = 0.00785 m2 Pipe cross-section, A2 = 0.0314 m2 Upstream pressure…

Q: oil (0.88) oil (0.88) Hg (SG=13.6) 320mm-

A:

Q: The pressure gauges are inserted at A and B in a vertical pipe converging water.  The diameters at A…

A:

Q: Problem 1. A 75-mm diameter orifice discharges 0.023 m3/s of liquid under a head of 2.90 m. The…

A: Given data,  Diameter of orifice = 75 mm Discharge = 0.023 m³/s Head = 2.9 m Diameter at vena…

Q: 4FT A h water

A:

Q: A liquid whose specific gravity is 2.0, is flowing in a 150mm diameter pipe. The total head at a…

A: To determine the discharge in the pipe for the given information.   Given, Specific gravity of the…

Q: 10.80. In frictionless oscillation of a U-tube, L = 4.0 ft, z = 0, V = 6 ft/sec. The maximum value…

A: Frictionless Oscillation of a Liquid in a U-tube. L=4 ft z=0 V=6 ft/sec g=32.174 ft/sec2

Q: In a uniform diameter smooth pipe measuring 30 cm, a pressure of 60 kPa was measured at section 1,…

A:

Q: 1. Differentiate between Rotational flow and Compressible flow

A: Hi! Thank you for the question As per the honour code, We’ll answer the first question since the…

Q: (Bernoulli/continuity) Water flows steadily through the pipe shown in the figure below such that the…

A:

Q: Glycerin at 20 °C flows upward in a vertical 75- mm-diameter pipe with a centerline velocity of 3.3…

A: Given: Diameter of pipe, D = 75 mm = 0.075 m Centerline velocity, Vc = 3.3 m/s Length of pipe, L =…

Q: Given a three-pipe system, the total 150,000 Pa, and the elevation drop data are:

A:

Q: 9.95. The mean velocity of water in a 150 mm horizontal pipe is 0.9 m/s. Calculate the loss of head…

A: Given, Diameter of the pipes= 150mm and 50mm Velocity in the 150mm pipe, v2= 0.9m/s Pressure in the…

Q: A horizontal 250-mm pipe suddenly enlarges to a 300-mm diameter. If the flow is 0.15 m³/s of water,…

A: Given data in question  Diameter 250 and 300 mm Horizontal pipe Pressure at smaller Diameter 265 kPa…

Q: What is pipe roughness? A pump is located 5 m above the surface of a liquid (y = 8170 M/m³) in a…

A: Given Data : f= 0.03 Dia (d)=0.2 m length (l)=60 m Power = 1.5 KW= 1500 W Length of suction pipe =…

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?