Figure shows that the pipe flow of 50 m^3/hr, is driven by pressurized air in the tank.   Determine the head loss in the "smooth" pipe in meters if its friction factor is 0.014. A. 12.9517 B. 39.5136 C. 99.9358 D. 30.4889 What gage pressure p1 in kPa, is needed to provide the given flow rate? A. 1121 kPa B. 1725 kPa C. 1692 kPa D. 1328 kPa

Q: A pressure gage at elevation of 12m at the side of the tank containing liquid reads 100 kPa. Another…

A: Given data in question  Elevation heads at 2 points Pressure at 2 points Since the cross section at…

Q: An inclined tank contains three different liquids A, B, and C with specific gravities of 0.40, 1.25,…

A: An inclined tank contains three different liquids A, B, and C with specific gravities of 0.40, 1.25,…

Q: The diameter of a pipe carrying water changes gradually from 150 mm at A to 450 mm at B. A is 5 m…

A: Given data,  Diameter at A = 150 mm Diameter at B = 450 mm Pressure at A = 70 Kpa Pressure at B = 50…

Q: A cylindrical tank having a diam. of 4 m/s and 8 m is full of water. There is an orifice at the…

A:

Q: Q2) water Flow upward at 4 m/s in a 6 cm pipe diameter. the pipe length between point 1 and point 2…

A:

Q: Figure shows that the pipe flow of 50 m^3/hr, is driven by pressurized aire in the tank. a.)…

A: Q = 50m3/hr  =0.1388 m3/sec f = 0.014 Length of pipe = l = 20+80+40 = 140m

Q: Oil flows from a tank through 150 m of 150 mm pipe and then discharges into air as shown. If the…

A:

Q: Question A horizontal pipe of non uniform cross section has water flow through it such that the…

A:

Q: Find the time it takes to decrease the water level in the tank 1 by 1.5m. Use C = 0.60 h.l. 2.3m do:…

A: Given data: diameter of tank 1 D1=6m Dimensions of tank 2 are 3m x 2m Difference in water level h=…

Q: A siphon consisting of a 3 cm diameter tube is used to drain water from a tank. The outlet end of…

A:

Q: 1 (

A:

Q: Water flows through a pipe at 5 L/s as shown. If the gage pressure of 12.5 kPa, 11.5 kPa and 10.3…

A:

Q: 2) ELEVATION 20oM ELEVATION 30m AIR Po? 150mmøØ SG 0-84 il flows from a tank through a 150mm…

A:

Q: At two points 1 and 2 in a pipeline the velocities are Vand 2V, respectively. Both the points are at…

A: given data : velocity at point 1= V velocity at point 2= 2V

Q: An orifice is attached to a vertical side of a cylindrical tank having a diameter of 4m. The weight…

A: Given:- Diameter of tank=4 mDiameter of orifice=90 mmWeight of water discharged=22563 N in time of 1…

Q: The pressure drop across a ball valve in a uniform diameter pipe is P1-P2 = 3572 psf. The inside…

A: Given:- The pressure drop across a ball valve = P1 - P2 = 3572 psf The inside flow area = 3 in2  The…

Q: A faucet is connected at the end of a pipe of roughness .00026. The pipe connected the faucet to the…

A: Given - Roughness = 0.00026 Pipe is connected to the water main, 40m away and 1.2m away. The…

Q: pipe carrying oil (SG = 0.877) change in size from 150mm diameter in point 1 to 450mm diameter in…

A: Head loss is generally a measurement of the energy dissipated in a fluid system due to friction…

Q: a cylindrical vessel has 0.5m diameter and 1m height rotates at 10rad/s. initial height of Mercury…

A:

Q: Water flows through an orifice at the vertical side of a closed cylindrical tank. The water level…

A:

Q: circular orifice of 50 mm diameter is fixed to the end of a water pipe of 75 mm diameter. The gauge…

A:

Q: 10.8 For laminar flow in a tube calculate the position of the average cross-sectional velocity.…

A: Step 1

Q: Oil (SG = 0.83) flows at a rate of 200 L/s through a 500m pipe with a diameter of 200mm. The…

A:

Q: Water flows downward in a pipe at 30°. The pressure drop P₁ - P2 is partly due to gravity and partly…

A: Given- Height difference=50 cm, Water flow in the pipe with parameter shown in the figure. It is…

Q: Gasoline having a specific gravity of 0.8 is flowing in the pipe shown at a rate of 5 cfs. What is…

A:

Q: i) Which of the following statements about a straight horizontal pipe of 6 inch diameter pressurized…

A: This question is related to the Fluid Mechanics from Civil Engineering. This is mcq type question.

Q: 10.80. In frictionless oscillation of a U-tube, L = 4.0 ft, z = 0, V = 6 ft/sec. The maximum value…

A: Frictionless Oscillation of a Liquid in a U-tube. L=4 ft z=0 V=6 ft/sec g=32.174 ft/sec2

Q: Determine the distribution of flow rate in the network

A:

Q: 7. For the Pitot Tube below, determine the height that the fluid rises, L, in the column if water is…

A: Velocity of flow through pitot tube is given and it has been asked to determine height of fluid…

Q: Subject hydraulics: Consider FIGURE R1M—3. Determine the discharge and the pressure head at A and B…

A:

Q: 43.A cylindrical thin-walled pressure vesSsel with radius r, wall thickness t, and modulus of…

A: Given data : Internal pressure=p radius=r wall thickness=t Modulus of elasticity=E

Q: 4. Water flows through a horizontal nozzle, as shown. At the nozzle inlet the diameter is 6in. At…

A: Given- Diameter at inlet is d=6inDiameter at outlet is d=2in

Q: Given a three-pipe system, the total 150,000 Pa, and the elevation drop data are:

A:

Q: 9.95. The mean velocity of water in a 150 mm horizontal pipe is 0.9 m/s. Calculate the loss of head…

A: Given, Diameter of the pipes= 150mm and 50mm Velocity in the 150mm pipe, v2= 0.9m/s Pressure in the…

Q: porous walls such that there is a radial outflow What is the rate of flow at B coming out from

A:

Q: 3. Medium lubricating oil (sg=0.85) is pumped through 360m of horizontal 75mm pipe at the rate of…

A:

Q: Water flow at a 250mm diameter horizontal pipe 875m long. The friction factor is 0.023. If the…

A: The given data is: Diameter of pipe, d=250 mm Length of pipe, L=875 m Friction factor, f=0.023 The…

Storm Sewers and Detention

The storm drains system transports rainwater or stormwater and other runoff from roads, parking lots, and roof downpipes directly to nearby creeks, rivers, or the sea without any treatment.