A closed cylindrical tank having a radius of 0.60m and a height of 4m is full of water under a pressure of 196.2 kPa. If the vessel is rotated at 200 rpm: (a) Compute the total pressure on the side wall and (b) compute the total pressure against the top. Imaginary water surface y%3D8.04 Closed- h=20 4m C P=wh -1.2-

A closed cylindrical tank having a radius of 0.60m and a height of 4m is full of water under a pressure of 196.2 kPa. If the vessel is rotated at 200 rpm: (a) Compute the total pressure on the side wall and (b) compute the total pressure against the top. Imaginary water surface y%3D8.04 Closed- h=20 4m C P=wh -1.2-

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Given; A hydraulic jack system (see figure) in an equilibrium condition, and data/properties as shown. Determine the Force F applied at the end of the lever arm to maintain equilibrium of the system. Neglect weight of plungers. Hint: Use the law of transmission pf pressure
A pump draws water from a reservoir A and lifts it to reservoir B as shown. The loss of head from A and lifts it to reservoir B as shown. The loss of head from A to (1) is 5 times the velocity head in the 12-inch pipe and the loss of head from (2) to B is 23 times the velocity head in the 7-inch pipe. Compute the pressure heads (2) in ft when the discharge is 447 gpm. Round your answer to 2 decimal places.
Two pipes A & B carries an oil of specific gravities 0.9 & 1.2 respectively. The center of the pipe A is 30 cm above the pipe B. The height of oil in right limb is 50 cm. Also, the mercury level difference is found in right limb as 90 cm. Find the pressure difference between these two pipes in kPa. Also find the pressure equivalent in water head in mm. The difference of pressure between two pipes (PA-PB) (Unit is in kPa) ? Equivalent to Water head in mm ?
The gage pressure (psig) at point a is nearest (a) 13.7 (b) 14.7 (c) 101.3 (d) 0 (e) 1 Oil a 3 in SG = 0.69 SThe gage pressure (psig) at point c is nearest (a) 57.2 (b) 1.4 (c) 6.7 (d) 0.4 8 in Water The absolute pressure (psia) the natural gas pipeline is nearest h, = 22 in (a) 8.4 (b) 65 (c) 9 (e) 23 16 in SThe gage pressure osig) in the natural gas pipeline is Natural gas Dif the pipeline pressure was increased by 50%, what cost- effective manometer modification(s) might be needed? (b) More mercury, less oil (c) Add 2 more manometer loops (d) Replace the manometer with a high-pressure gage (e) Rotate the gas line to a vertical alignment Mercury SG = 13.6
i)Calculate the flow rate through the system.
tank contains water upto a height of 1 m above the base. An immiscible liquid of sp. gr. 0.8 is filled on the top of water upto 1.5 m height. Calculate : () total pressure on one side of the tank, () the positiom of centre of pressure for one side of the tank, which is 3 m wide.
Consider the figure shown below. If the flow rate of water from the tank is 0.03 m/s, the pressure at point 2 is 120kPa. Height of water in the tank is 4m and the pipe diameter is 160mm with a friction factor of 0.020. Solve for the height h if the branch line is shut off, and if the branch line is open so that half of the flow from the tank goes into the branch and half continues in the main line. Determine the difference in the head losses in both directions. Neglect minor losses. Vent | 4m 160mmø pipe Branch Line B A 1.75m Main Line 300m 200m ANSWER: a. h = 13.918m, b. h = 10.585m c. HL = 3.2479m