Q2:B) Calculate the power required to pull (1.5m x 1.5m) flat plate at speed (1 m/s) to the left side over a horizontal surface with 100 mm spacing. The oil between the surfaces has (p = 900 kg/m³, u= 0.06 Pa.s). The pressure difference between points 1 and 2 is (P₁- P2=100 kPa). Assume laminar viscous flow. oil 100 mm NO

Q2:B) Calculate the power required to pull (1.5m x 1.5m) flat plate at speed (1 m/s) to the left side over a horizontal surface with 100 mm spacing. The oil between the surfaces has (p = 900 kg/m³, u= 0.06 Pa.s). The pressure difference between points 1 and 2 is (P₁- P2=100 kPa). Assume laminar viscous flow. oil 100 mm NO

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

mater 7
I need the answer as soon as possible
The pipe bend shown is in a horizontal plane. Oil with a specific gravity of 0.86 enters the reducing bend at section A with a velocity of 3.2 m/s and a pressure of 150 kPa. Neglecting head loss, determine (a) The velocity at section B, V3 (m/s) (b) The pressure at section B, ps (kPa) (c) FMx (N) de = 100 mm B da = 150 mm 30°
Determine (a) the magnitude and (b) direction of the anchoring force needed to hold the horizontal elbow and nozzle combination shown in the figure below in place. Atmospheric pressure is 97.1 kPa. The gage pressure at section (1) is 103 kPa. At section (2), the water exits to the atmosphere. Assume p₁ = 103 kPa, V₁ = 4 m/s. (a) Kx = i 2260.24 (b) to the left N V₂ 160 mm Section (2) 300 mm V₁ Water Section (1) P1 V₁
SITUATION #2 Determine the maximum diameter of the cylinder tank if the internal pressure is 127 kPa. Given the allowable stresses for longitudinal 140 MPa and tangential 100 MPa. L = 10 m
Solve with clear solution.
Air at 30°C flows through a 70 m long, 2 cm x 2 cm rectangular cross section pipe as shown in Figure 1(b). The flow is laminar flow and centerline velocity is 2 m/s. If the angle of pipe measure from horizontal plane is 35º, determine : (iv) wall shear stress; (v) shear stress at 1 cm from the center of the pipe; and (vi) power required to maintain this flow.
25 pts A circular door having a diam. of 3m closes a horizontal duct from a small diam. as shown. The center of the door is 4.5m below the liquid surface. Assuming the specific gravity of liquid is 0.9o. Compute the following: a) hydrostatic force acting on the door, [ Select ] b) the location of the center of pressure from the centroid of the door, [ Select ] c) the force at the bottom of the gate to maintain equilibrium if it is hinged at the top. [ Select ] 4.5 m 3m
A tank 13 ft deep and 5 ft wide is layered with 6 ft of oil (y = 50.0 lbf/ft3), 5 ft of water, and 2 ft of mercury (y = 846 lbf/ft3). Compute (a) the total hydrostatic force and (b) the resultant center of pressure of the fluid on the right-hand side of the tank.