X N/m A В -Y m Z m Figure Q2(a) Table 02(a): Parameter Student with EVEN last digits of matric number (AD20xxxZ) Z = 0,2,4,6,8 Parameter 1200 N/m 1.2 m X Y 0.8 m Q2 (a) The uniformly loaded beam ABC has simple supports at A and B and an overhang BC (see Figure Q2(a)). Values X, Y and Z are given in Table Q2 (a). (i) Determine the support reaction of the beam. (ii) Draw the shear diagram and determine the point on the beam where the zero shear occurs. (iii) Draw the moment diagram and determine the points where the zero moment occurs.

X N/m A В -Y m Z m Figure Q2(a) Table 02(a): Parameter Student with EVEN last digits of matric number (AD20xxxZ) Z = 0,2,4,6,8 Parameter 1200 N/m 1.2 m X Y 0.8 m Q2 (a) The uniformly loaded beam ABC has simple supports at A and B and an overhang BC (see Figure Q2(a)). Values X, Y and Z are given in Table Q2 (a). (i) Determine the support reaction of the beam. (ii) Draw the shear diagram and determine the point on the beam where the zero shear occurs. (iii) Draw the moment diagram and determine the points where the zero moment occurs.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The cantilever beam consists of a rectangular structural steel tube shape [E = 28000 ksi; I = 530 in.4]. Use double integration to determine:(a) the beam deflection vB at point B. [ Answer: vB = -.424 in](b) the beam deflection vC at point C. [ Answer: vC = -.894 in]Assume P = 12.9 kips, w = 2.7 kips/ft, LAB = 7.0 ft, LBC = 4.3 ft.
Determine the support responses at point A of the cantilever beam shown in the figure below.
need help on this
A bus’s leaf spring has following data-Number of leaves = 15 Each leaf’s width = 15 mmThickness = 12 mmMain leaf’s span = L = 2l = 400 mm.Modulus of elasticity, E = 200 GPa.Under a static load w, the tip deflects by 40 mm. Find,i) The value of w.ii) The maximum stress.
A wooden beam is loaded by a distributed load w = 5 N/mm as shown in Figure Q4(a). The cross-section of the beam is shown in Figure Q4(b). Assume that LAB = 1600 mm, LBC = 3400 mm, W=190 mm, Bo = 20 mm, and H = 200 mm, ho=40 mm. Units: use N, mm, MPa as consistent units for all calculations. Decimal points: any decimal points are fine and all the numerical questions have a 10% error tolerance. (а) (b) hot Bo H LAB LBC Cross-section W Figure Q4: (a) A wooden beam is loaded by a distributed load, (b) cross-section of the beam.
El = 2.5(1010) N.cm? El = 1.5(1010) N.cm? El = 1.3(1010) N.cm? 6m 4m 2m 2.5(10°) 2.5(10°) 1.5(10°) Figure. 1: Simply supported beam subjected to moment distribution Critically analyse the finite element product and systems model that help to find and solve the problem shown in Figure.1 by performing the following steps: Construct one-dimensional elements line (i.e., grid/mesh line), make the correct numbering and labeling of nodes and elements. b. Construct grid/mesh information table c.. Write the shapes function, N; and N; for each element (e) and plot the shape function diagram а. d. Construct the weight functions for the one-dimensional elements' line/mesh. Calculate the nodal deflection values and the distribution through each element using element matrices- е. Galerkin's method. f. Would you increase (refine) the number of nodes/elements for this problem, explain you answer? g. Justify your mesh/grid divisions for this problem in terms of complication of geometry or materials…
y 1/4 F₁ X1 (У1 Y₂ Y₁ 1/4 F2 X2 1 Matrix and Determinants Displacement y = y(x) 9 11 :) = *- ( ²17 1/4 3 7 11 1/4 Y₂ Уз F3 X3 1 7 K 11 16 11 F₂ F Due to three forces F₁, F2 and F3 applied perpendicular a beam is displaced, as indicated in 1/4 the figure. The relationship between the applied forces and the displacements can be expressed as X with K = = [³ 768 E I For the three forces applied, F₁ = 2000 N, F₂ = 4000 N and F3 = 3000 N, determine the displacements y₁, Y2 and y3. Assume a beam length | = 1 m, and the product E-I = 5.10¹0 N/mm². Use for your calculations two decimal places and state your result as a vector including units.
and y vs. y (phase plot) 4. Consider the deflection v of the beam to the right. The beam is supported at each end and sags due to its own weight (a distributed load q = 50 kN/m). The equation describing the deflection is d'u qx (x- L) dx 2EI where L=5.0 m, I = 0.0052 m* and E = 1.0x1010 Pa. Use the method of your choosing (shooting or finite differences) to solve for: 1) the slope at each end of the beam; 2) the maximum deflection; and 3) the location of maximum deflection.
Consider the beam in the picture below: 7kN/m 5kN/m P N/m Section 1 Section 2 Section 3 - L/3 L/3 L/3 %3D Take P = the last four digits of your student number in N/m. If P<250 N/m then take P = 30OON/m instead. Take L = the third digit of your student number, reading left to reight. If this value is zero then take L = 2 Assume: The reaction at the Pin = V pin 47000L+9PL )N 54 The reaction at the Roller = Vroller = 61000L+9PL 54 and that both reactions act vertically upwards. a) Find an expression for the internal moment for Section 1. Show all working and any relevant free body diagrams. b) What is the maximum magnitude of the internal moment for Section 1? Mark sure you prove that the value you calculate is the maximum. c) Find an expression for the internal moment for Section 2. Show all working and any relevant free body diagrams. d) What is the maximum magnitude of the internal moment for Section 2? Mark sure you prove that the value you calculate is the maximum. e) Find an…
For the cantilever steel beam [E = 230 GPa; 1= 86 x 106 mm4], use the double-integration method to determine the deflection vg at B. Assume L = 3.3 m, Mo = 79 kN-m, and w = 11 kN/m. "| A Answer: VB = i W L mm. B Mo
Note: The solution should not be hand written.
Derive the weak form of the problem. Pay attention to the treatment of boundary conditions and body loads.