Answered: What will be the load carrying capacity…

What will be the load carrying capacity (kN) of a group of 6 piles, if the individual load carrying capacity is 150 kN and group efficiency is 75%.

Principles of Foundation Engineering (MindTap Course List)

9th Edition

ISBN:9781337705028

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter14: Piled Rafts: An Overview

Section: Chapter Questions

Problem 14.2P: In a piled raft, 450 mm diameter and 13 m long piles are placed in a rectangular grid at 1.60 m ...

See similar textbooks

Related questions

Q: Complete the table below. LINE BEARING DIST (M) AB N 68° 11.9' E 53.852 BC S 45° 0' E 28.284 CD S…

A: Latitudes:- Latitude of line AB =53.852×cos(68°11.9')=20.001 Latitude of line BC =…

Q: find the velnes ofthe following Limits 3-Lim ux X-)o tanst

A: Firstly substituting x=0 in given limit we will find the form of limit if it is 0/0 form then we…

Q: How did you get PA

Q: What are the three main types of Fluctuation Clauses?

A: Fluctuation clauses are the clauses that are added to a construction contract and are used to deal…

Q: 4.31 Determine the forces in the top chord member GH and the bottom of the truss, if h = 3 ft. How…

A: Reactions :ξFy=0 ; Ay+Ey=160KNξMA=0 ; 8Ey=402+404+406+208 Ey=80 KN & Ay=80…

Q: Discuss Drilling Rigs

A: Drilling rigs:

Q: express each common fraction as a decimal fraction. 5⁄64

A: Given data:- The given each common fraction is, 564

Q: One acre is 160 rod2. Isn't it 1rod2 = 5yd2, 160rod2 = 800yd2? So why should 1acre= 4,840yd2 be…

A: 1 acre = 160 square rods. 1 square rod = 30.25 square yards

Question

Piles

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given data

VIEW

Step 2: calculation

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

What will be the load carrying capacity (kN) of a group of 6 piles, if the individual load carrying capacity is 150 kN and group efficiency is 75%.
What is the ultimate capacity in kN of the pile group shown in the figure assuming the group to fail as a single block? 1.2m cc 0.4m diameter piles Clay soil Cu-40kN/m2 1.2m oc
Piles are needed to support columns in a high rise building at a particular site. The probability of failure of a pile due to excessive axial load is estimated to be 10 Suppose that four soch piles are required under each colunas and there are 20 identical columns in the filding Assume that the failure of piles are statistically independent of mach other. (a) What is the probability that none of the piles under a column foundation will fail (b) What is the probability that none of the columns in a building will staffer damage due to p pile failure?
Problem 3: You have been assigned to check the geotechnical capacity of a concrete pile foundation designed by your colleague. The design drawing shows 27m long 600mm diameter concrete piles. The specified end bearing capacity is 3000 kPa (ULS). The total factored ULS load on the pile is 2210 kN. The geotechnical engineer specified the following parameters: End bearing reduction factor =0.95 Skin group reduction factor = 0.9 ULS geotechnical resistance factor = 0.6 Elevation (m) Ultimate unit From То skin friction (КРa) 15 1106 1104.5 1102.5 1104.5 35 Check if the pile has adequate geotechnical capacity. 1102.5 1092 45 1092 1085.5 55 1085.5 1083 70 1083 1080 110 1080 1076 230
I need correct solution chegg solution is incorrect
The group efficiency factor for piles in saturated clay is low soon after driving, and increases with time. Why does this occur?
c) Several different items are used in the design and construction of piles, including: i) Engineering Analysis ii) Field Load Tests Discuss the above items
A group of twelve prestressed concrete piles is to support a building column. The total downward design load on the group is 4,900 k. Assuming this load is evenly distributed across the 12 piles, and that there are no moment or shear loads, select a pile size and 28-day compressive strength of the concrete.
i need the answer quickly
Please explain with solution
Q- Find the total load carrying capacity of a group of 9 piles with a group efficiency factor of 0.9. Given that the load carrying capacity of an individual friction pile is 200 kN.
Estimate the group efficiency of a 4 x 6 pile group, consisting of 400 mm diameter concrete piles at 1.2 m center-to-center spacing using a. the Converse-Labarre equation b. the Los Angeles Group Action equation