What are the following control signals will be set into for "bne"? Explain your answer for each part. A. RegWrite B. ALUSrc C. ALUOP D. MemWrite PC Read address Add Instruction Instruction memory Read register 1 Read register 2 Write register Registers Read data 2 Write data RegWrite Read data 1 16 Sign- extend 32 Shift left 2 ALU Add result M u ALUSIC 4 ALU operation PCSrc Zero ALU ALU result Address Write data MemRead MemWrite Read data Data memory MemtoReg

What are the following control signals will be set into for "bne"? Explain your answer for each part. A. RegWrite B. ALUSrc C. ALUOP D. MemWrite PC Read address Add Instruction Instruction memory Read register 1 Read register 2 Write register Registers Read data 2 Write data RegWrite Read data 1 16 Sign- extend 32 Shift left 2 ALU Add result M u ALUSIC 4 ALU operation PCSrc Zero ALU ALU result Address Write data MemRead MemWrite Read data Data memory MemtoReg

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

The loop instructions transfer execution control to another point designated by the instruction pointer. (ip) O (ecx) + sign extended 8-bit displacement (ip) + sign extended 8-bit displacement O (ip) + unsigned 8-bit displacement O (ecx) + unsigned 8-bit displacement
Fill the table with the correct starting and ending address in correspond to E register's content under real mode operation: Show your solution. Segment Register 1. CS = 0A1BH 2. DS = 1234H Starting Address Ending Address
Add Add Sum 1 Shift left 1 Branch MemRead Instruction [6-0] MemtoReg ALUOP Control MemWrite ALUSCC RegWrite L3 Instruction [19-15] Read address Read register 1 PC Instruction (24-20] Read data 1 Instruction [31-0] Read register 2 Zero ALU ALU Read Instruction [11-7) Read data 2 Address Write result data Instruction register memory Write data Registers Write Data data memoryl Instruction (31-0) 32 Imm 64 ALU Gen control Instruction [30,14-12] During a particular clock cycle, consider the CPU shown in the drawing. Assume that the following initial data is present (all values are shown in decimal, DM is Data Memory): x8=72. x18=56, DM(64) =48 During the cycle in question, assume that the following instruction is executed (the first column is the instruction's address: all values are shown in decimal): 51868 Id x8.8(x18) Write below the value of the bus L1 in decimal: L1 Write below the value of the bus L2 in decimal: L2 Write below the value of the bus L3 in decimal: L3
Write a single rotate instruction that swaps the DL register's high and low halves.
An 'instruction fetch/read' results in three sets of numbers that go to the Registers Block as studied in class. These three numbers in the instruction represent bits 25-21 for 'Read Register 1', bits 20-16 for 'Read Register 2', and bits 15-11 for the 'Write Register'. What does the 5 bits width of each of these indicate? a. That the word is 15 bits long in this architecture b. That each word is 32 bits long c. That there are 32 registers that can be addressed in this architecture d. That there are 15 registers that can be addressed in this architecture
2. Draw an R-type datapath with an Instruction Fetch unit. Point to be noted, the ISA and ALU both are 16-bits. R-type Op (4 bit) Rs (4 bit) Rt (4 bit) Rd (4 bit)
Assume that before the instruction is executed, the flags are CF=0, ZF=0 and SF=0 and the Registers have the values AL=0x86, BL=0x81, CL=0x37 and DL=0x87. What are the values of the flags after the instruction OR DL, DL executes? CF = ZF = SF =
For the RISC-V assembly instructions below, what is the corresponding C statement? Assume that the variables f, g, h, i, and j are assigned to registers x5, x6, x7, x28, and x29, respectively. Assume that the base address of the arrays A and B are in registers x10 and x11, respectively. sub x30, x28, x29 slli x30, x30, 2 add x3, x30, x10 add x4, x30, x11 1w x30, 0 (x3) 1w x31, 0 (x4) add x30, x30, x31 sw x30, 16 (x11)
An instruction is stored at location 100 with its address field at location 101.The address field has value 200. A processor register R1 contains the number 300. Evaluate the effective address if the addressing mode of the instruction is A. Direct B. Immediate C. Relative D. Register Indirect E. Index with R1 as the index Register
Consider the below instructions and write the datapath components that each of these instructions use for completing the instruction: 1. AND $t0, $t1, $t22. SW $t1, 44 ($t2)3. BNE $t1,$t2, ELSE
Computer Science - Assembly language code: Q1. A) A microprocessor is wired into a sensing control circuit so that the memory locations 42 and 43 each contain the values 0 or 1. Memory location 50 is connected to a light switch. When the value in 50 is 1 the light is on and when it is 0 the light is off. Write a program to switch on the light on when the values in locations 42 and 43 are both 1, and to switch off the light when the values in locations 42 and 43 are both 0. Only use the ARM assembly language instructions, MOV, JMP and JNZ. Assume that the MOV instruction updates the flags with the status register.
20 LDA 50 21 SUB 51 50 100 51 200 Choose the contents of the registers: PC, MAR, MDR, IR, A at the end of fetch-execute cycle for instruction 20: PC MAR MDR IR A