water enter an inward flow turbine at an angle of 22° to the tangent to the outer rim and leaves the turbine radially. The speed of the wheel is 300 rpm and the velocity of flow is constant at 3 m/s. find the necessary angle of the blade when the inner and outer diameter of the turbine are 30 cm and 60 cm respectively. If width of wheel at inlet is 15 cm, calculate HP developed. Thickness of blade may be neglected.

water enter an inward flow turbine at an angle of 22° to the tangent to the outer rim and leaves the turbine radially. The speed of the wheel is 300 rpm and the velocity of flow is constant at 3 m/s. find the necessary angle of the blade when the inner and outer diameter of the turbine are 30 cm and 60 cm respectively. If width of wheel at inlet is 15 cm, calculate HP developed. Thickness of blade may be neglected.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

380 Q-24: A pipe of diameter d and length L leads from a reservoir. At the discharge end a nozzle of diameter d is fitted. At the inlet of pipe head available is H. The nozzle is discharging into atmosphere. Prove that for maximum power transmitted by the nozzle dn d5 2fL Head loss in pipe is given by h, = fLV 2gd where f = Darcy's friction factor.
The turbine shown below develops 120 hp (66000 ft Ib/s) when the flow rate of water is 15 ft /s. If all losses are negligible, determine the pressure difference across the turbine (i.e., P4-P3). Answer should be in units of Ib/ft?. (Specific weight of water = 62.4 lb/ft3) P4 12 in.. 12 in. T Free jet
B A shaft turns at 150 rpm under a torque of 1500 Nm. Power transmitted is (a) 15 kW (b) 10R kW (c) 7.5 kW (d) 5 kW
Give me all answers otherwise leave it. I I don't want partial answers. I remember please give me a, B, c, d and e... Please thank you
A centrifugal pump supplies water at the rate of 400 liter/s and the pressure difference (AP) across pump is 200 kN/m². Diameter and width of the impeller at outlet are 40 cm and 10 cm respectively. Blade thickness occupied 10 percent of the circumference. Impeller inlet diameter is half of the outlet diameter. If the blades are radial, find: Assume zero whirl at inlet (V₁=0; V₁_V₁₁; a=0) and diameter of suction and delivery pipes are equal (V₁₁ V₁₂). 1=r12 (i) The pump power input if overall efficiency is 80 percent (ii) The impeller speed in rpm, and (iii) Inlet blade angle
4.(c) An inward flow reaction turbine has an inlet and outlet diameter of 1.5 m and 0.75 m respectively. The breadth at the inlet is 0.30 m and at the outlet is 0.40 m. At a speed of rotation of 300 rpm., the relative velocity at the entrance is 5.25 m/sec and is radial. Calculate the (i) absolute velocity at entrance and inclination to the tangent of the runner; (ii) discharge; (iii) velocity of flow at the outlet.
Water is pumped from reservoir A at elevation 250 m. The pump is close to reservoir A and is at the same elevation as reservoir A. It is pumping 90 liters per second of water through a 1,000 m of 150 mm diameter pipe to a reservoir whose elevation is 300 m. What is the horsepower delivered by the pump? Assume f=0.02 and neglect minor losses. Select one: O a. 150.50 Hp O b. 302.23 Hp O c. 267.72 Hp O d. 252.30 Hp