Q2)For the systemshowninthefigure, the waterflowrateis(40)L/s. Find the30mpower transferredfrom the flow byCast iron pipeCast iron pipeL=46mL=60mtheturbine,d=6 ind=8 inK=3[v=1x10°m²/s].gate valveTurbine6 in.[Ans. 10.37kW]K=0.990° elbowTwo 8 in. 90° elbowsK=0.75 for each

To find :- Power transferred from the flow by the turbine.

Q2)For the system shown in the figure, the water flow rate is (40)L/s. Find the 30m power transferred Cast iron pipe from the flow by Cast iron pipe L=46m L=60m d=6 in the turbine, d=8 in K=3 [v=1x10°m?/s]. gate valve Turbine 6 in. [Ans. 10.37kW] K=0.9 90° elbow Two 8 in. 90° elbows K=0.75 for each

Q2)For the system shown in the figure, the water flow rate is (40)L/s. Find the 30m power transferred Cast iron pipe from the flow by Cast iron pipe L=46m L=60m d=6 in the turbine, d=8 in K=3 [v=1x10°m?/s]. gate valve Turbine 6 in. [Ans. 10.37kW] K=0.9 90° elbow Two 8 in. 90° elbows K=0.75 for each

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Question 2 Oil (SG = 0.85) is flowing in a 10cm diameter pipe. The elevation of the pipe is 5m above the datum line and the pressure in the pipe is -24KP.. If the discharge in the pipe is 30 L/s, determine the power (in watts) in the stream at that point. A 843.17 Watts B 648.28 Watts (c) 926.41 Watts D No answer among the choices E 716.69 Watts
A Francis turbine has an inlet diameter of 2 m and an outlet diameter of 1 m. The breadth of the blades is constant as 0.2 m. The peripheral velocity at inlet is given as 25 m/s. The vanes are radial at the inlet and the discharge is radially outwards at the outlet. The peripheral velocity of the blade at outlet will be (a) 15 m/s (c) 20 m/s (b) 25 m/s (d) 12.5 m/s
Q-2.3 A kaplan turbine develops, 1500 kW power at average head of 30 meter. The speed and flow ratios are 2.1 and 0.62 respectively. The diameter of boss = 0.4 times the external diameter of runner. Overall efficiency being 90%. Calculate diameter and speed of runner.
shows a pump employed for lifting water from a sump. If its required to pump 60 liters/sec of water through a 0.1 m diameter pipe from the sump to point 10m above, determine the power required. Also determine pressure intensities at L and M. Assume efficiency of 70%. Pu-(YGYLD)
A liquid whose specific gravity is 2.0, is flowing in a 50mm diameter pipe. The total head at a given point was found to be 17.5m. That point is 3m above the datum and the pressure in the pipe is 65.6KP.. Compute the power in that point of the pipe. Hide answer choices a A) 13.37 HP B) 14.99 HP 8.87 HP D) 11.19 HP E No Answer among the choices O O O
5): For the system shown below: 1-Find the water power of the turbine (PT) if the required power output is PE (take PE between 5-25 kN) and the turbine efficiency is n (take n between 75 to 98%) 2- Find the flow rate in the pipe AB. 3-Find the value of Z1 for operating this system (take Z2 between O to 20 m). * Pitot tube Piezometer. 0.3m 1.0m z1 22 T. Id= 200mm d= 100mm
During a flow of 450 L/s, a pressure of 65 kPa was measured at point C in 320 mm diameter horizontal the supply line of water turbine and a -47 kPa pressure T. was measured at point D, 2 m below point C at the 460 diameter exit pipe. mm Compute the total head extracted by a. the turbine. b. Compute the power supplied to the turbine in horsepower.
A submersible deep well pump delivers 800gal/h of water at 60°F through a 1in SH. 40 SP, when operating in the system shown below. If the total length of pipe is 150ft, calculate the power delivered by the pump to the water. Consider friction loss, but neglect the other minor losses.