7-a)b)c)d)For the transmission line shown below, what is the power of the pump with efficiency of 70% to deliver200 lit/s of water (y=9806 N/m³) from point I to point 4 if the slope of hydraulic grad line is:J=hi/L=3.66 x 10³ m/m.30 mP84.5 KW102.46 kW90.53 KW89.22 KWLeave blankL = 1000 m2180 mL = 1000 m3L = 1300 m105 m320 m

Efficiency, η=70% Flow rate, Q=200 lit./s The density of water, ρ=9806 N/m3 The slope of the…

7- a) b) c) d) For the transmission line shown below, what is the power of the pump with efficiency of 70% to deliver 200 lit/s of water (y=9806 N/m³) from point 1 to point 4 if the slope of hydraulic grad line is: J=hr/L=3.66 x 10³ m/m. 30 m P 84.5 KW 102.46 kW 90.53 KW 89.22 KW Leave blank L = 1000 m 2 180 m L = 1000 m 3 L = 1300 m 105 m 320 m

7- a) b) c) d) For the transmission line shown below, what is the power of the pump with efficiency of 70% to deliver 200 lit/s of water (y=9806 N/m³) from point 1 to point 4 if the slope of hydraulic grad line is: J=hr/L=3.66 x 10³ m/m. 30 m P 84.5 KW 102.46 kW 90.53 KW 89.22 KW Leave blank L = 1000 m 2 180 m L = 1000 m 3 L = 1300 m 105 m 320 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Figure 2 is a schematic of a pumped-storage system. How much power must be supplied to the water by the pump (in kilowatte) talpump water at 0.085 m/s at 20°C from the lower to the upper reservoir? Deo A Figuro 2: Pumping from lower to higher elevation The head loss in the pipes is h, 0.018 where Lis the length of the pipe in metors, and D is the diameter of the pipe in meters. D 25 Sketch the HGL and EGL for the system
The following figure shows a pump that extracts water from a reservoir with a volumetric discharge rate of Q L/s. Assume all losses are negligible. a) What would be the pressure at points A and B, when the pump-motor system extracts P kW from the electric grid. The combined efficiency of the pump-motor system is 60%. b) Draw the Energy Grade Line (EGL) and Hydraulic Grade Line (HGL) for this system. Q = 0.055 L/s; P= 20 kW B 1.2 m Atmosphere C 3.0 m Diameter: 10 cm Pump Diameter: 15 cm
Pump BC shown brings oil (SG = 0.72) to reservoir D at 170 L/sec. The energy lost from A to B is 1.1 J/N and from C to D is 4.7 J/N. How many hp is needed for the pump to function if its efficiency is just 80%? a)86.531 hp b)135.204 hp c)187.785 hp d)120.182 hp
Pump BC shown brings oil (SG = 0.72) to reservoir D at 170 L/sec. The energy lost from A to B is 1.1 J/N and from C to D is 4.7 J/N. El. 84 m D EL 22.6 m A 0.30-m Ø B El. 2.8m How many hp does the pump supply the system? O 108.164 hp O 112.069 hp O 150.228 hp O 80.690 hp
HYDRAULICSPLEASE PROVIDE COMPLETE SOLUTIONNEED ASAP THANKS
The pump whose characteristics are: H, = 80 – 600V²2 %3D n = -1500V² + 700V Elevation = 230 m |(2) (1) Elevation = 200 m 1000 m pipe 40 cm in diameter Pump Figure Q3 is used to pump water (µ=0.001kg/ms) a distance of 1000 m between two reservoirs the elevations of which are shown in Figure Q3 and remain constant. The pipe is 40 cm diameter commercial steel (ɛ=0.046 mm). Ignoring minor losses and assuming fully turbulent flow. Determine d) The volumetric flow rate e) The efficiency at the operating point
A 90% efficient pump lifts water from a lower reservoir a shown in the figure. The head loss in the 150mm pipe is 3 times the velocity head in that pipe and the head loss in the 100mm pipe is 20 timew the velocity head in that pipe. A.If the desired flow rate is 20L/s ehat shoukd be the powet input of the pump in Kw? Choices: 42.9,28.8,32.0,38.6 B.Compute the pressure head, in m of water, at the suction line before the pump Choices: 12.39,10.29,9.74,7.56 C.Compute the pressure head,in m of water, at the discharge line right after the pump. Choices: 156.26,136.80,139.53,145.20
Mato 9
9.The pump shown delivers 115 li/s of oil, sg = 0.84, toreservoir D at elevation 72 m. The energy lost in thesuction line is 3.2 J/N and in the discharge line is 7.6 J/N. a.Compute the total head added by the pump. b.How many kW does the pump supply the system? c.If the pump is 85% efficient, how much power does it need?
The following applies the figure (6): {PA= 207 kPa.), (P= 689.44kPa.), (Q= 0.14 m²/s), elevation of point (A) is (67 m), elevation of point (B) is (30.48 m ) .Is the machine at (C) a Turbine or Pump?. What is the power associated with this machine?. d = 0.3 m A d = 0.2 m B Figure (6)
What is the head that must be supplied by the pump to the water to pump 0.4 m³/s from the lower to the upper reservoir ? Hint: [The head loss in the pipes is given in the figure as a function of water velocity]. Elevation = 150m Water Elevation 100m h₁=45v²/2g d=15cm Water Pump h=22.5v²12g d=20cm Elevation 40m
A booster pump is installed in the pipeline between the two reservoirs. If the energy head increased by the pump is 20 m, then what is the flow rate in the pipeline? Assume that length of pipeline is 1500 m, diameter of pipe is 300 mm and coefficient of friction is 0.02. -R.L = 200 m 300 mm Pump B R.L = 185 m