A submersible deep well pump delivers 800gal/h of water at 60°F through  a 1in SH. 40 SP, when operating in the system shown below. If the total length of pipe is 150ft, calculate the power delivered by the pump to the water. Consider friction loss, but neglect  the other minor losses.

Q: Q2)For the system shown in the figure, the water flow rate is (40)L/s. Find the 30m power…

A: Given  Discharge, Q = 40 l/s = 0.04 m3/sec Kinematic viscosity = 1 x 10-6 m2/s  Total head = 30 m To…

Q: The turbine shown in the figure below develops 106 hp when the flowrate of water is 26 ft³/s. If all…

A: P=106hp Q=26ft3/s To find  h ∆P Q

Q: Water from an open tank elevated 5m above ground is allowed to flow down to a pump. From the pump,…

A: Given, L = 100 m np = 55%  Q = 0.8 m3/min or 0.0133 m3/s

Q: 7.30 FLUS For this refinery pipe, DA = 20 cm. Dg = 14 cm, and L= 1 m. If crude oil (S = 0.90) is…

A:

Q: The turbine in the sketch has a flowrate Q = 100 m³/s and the outlet has a circular cross- section…

A: Solution: Given: Discharge Q= 100m3/s Diameter D=2m Total head HT= 100m Head Loss H=20m The…

Q: 7- a) b) c) d) For the transmission line shown below, what is the power of the pump with efficiency…

A: Efficiency, η=70% Flow rate, Q=200 lit./s The density of water, ρ=9806 N/m3 The slope of the…

Q: A pump is used to lift 120 L/s of water at 10°C from a river to a storage tank that has a free…

A: Given, Q = 120 L/s or 0.12 m3/s D = 350 mm or 0.35 m  L = 1200 m  e = 0.02 mm

Q: In the simple hydraulic circuit shown in Figure 1 below, why is the counterbalancing pressure valve…

A:

Q: Neglecting losses, calculate V2 (ms) of water existing the nazzle D1 = 10 cm D2 = 2.5 cm P1 = 1600…

A: Given: The diameter D1 is 10 cm. The diameter D2 is 2.5 cm. The pressure P1 is 1600 kPa. The…

Q: In the figure the water (P = 1000 kg/m3) enters the pump to be raised at (1), with a pressure P1 =…

A:

Q: If water is pumped from reservoir 1 to reservoir 2 through a 20 cm pipe with a length L1=70 m, and…

A: The expression for velocity in pipe is given as V=QA Substitute the value in above expression V=0.15…

Q: Q-2.3 A kaplan turbine develops, 1500 kW power at average head of 30 meter. The speed and flow…

A: - Speed ratio = μ12g H  μ1 = 2.1 × 2 × 9.81 × 30 = 50.95 m/s - Flow ratio = μf12g H  μf1 = 0.62 × 2…

Q: shows a pump employed for lifting water from a sump. If its required to pump 60 liters/sec of water…

A:

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?