380 mwak Q-24: A pipe of diameter d and length L leads from a reservoir. At the discharge end a nozzle of diameter d is fitted. At the inlet of pipe head available is H. The nozzle is discharging into atmosphere. Prove that for maximum power transmitted by the nozzle dn = d5 2fL Head loss in pipe is given by h, = fLV 2gd where f= Darcy's friction factor.

380 mwak Q-24: A pipe of diameter d and length L leads from a reservoir. At the discharge end a nozzle of diameter d is fitted. At the inlet of pipe head available is H. The nozzle is discharging into atmosphere. Prove that for maximum power transmitted by the nozzle dn = d5 2fL Head loss in pipe is given by h, = fLV 2gd where f= Darcy's friction factor.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

shows a pump employed for lifting water from a sump. If its required to pump 60 liters/sec of water through a 0.1 m diameter pipe from the sump to point 10m above, determine the power required. Also determine pressure intensities at L and M. Assume efficiency of 70%. Pu-(YGYLD)
The total head loss from A to E as shown in the figure is 20 meters. Use friction factor, f = 0.02 in all pipes. Find the discharge at line 3 in m3/s Round your answer to 3 decimal places.
A galvanized-iron pipe (ε = 0.0005 ft) is to carry air at standard temperature and pressure at a rate of 2.0 ft3/s. The pressure drop is to be no more than 0.50 psi per 100 ft. Design the pipe diameter.
The venturi meter is being used to measure the flow of fuel oil (sp gr = 0.858). The differential gage fluid is water. The meter coefficient is 0.975. Compute the discharge if z is 16 inch. 3 inch 1 inch echplic.c
Note: Don't copy from Chegg.
(b) A water turbine model is constructed at ratio of 1:8 with power system of 10 kW at speed of 555 rpm under a head of 2.5 m. Overall efficiency for both model and prototype is assumed at 0.93. (i) Detemine the specifie speed. mine t); (ii) If the prototype is run under a head of 25 m, calculate its rotational speed, power and discharge.
solve for: BHP² HT² N² When: BHP¹ = 414.14hp HT¹ = 6.56m N¹ = 0.8 WHP = 331.31hp TY!
Plz write neat
Prob-2 A hydraulic power system consists of a dam with an inlet connected to a turbine. H=15m, V₂-5m/s. Q=1m³/s. (hL is negligible); Point 1 and 2 open to atmosphere. V₁-0) Find: Power produced by turbine (kW). Last week Turbine As
- Probl Water flows from a large open tank, through a valve and out a pipe to atmosphere. A-9 cm². Az = 11m. h₁ = 5V²/2g Find: I Discharge (Q=?) in pipe. Assumptions: a = 1.
Give me all answers otherwise leave it. I I don't want partial answers. I remember please give me a, B, c, d and e... Please thank you
Problem 2: A centrifugal pump with an overall efficiency of 0.56 rotates at 1650 rpm. The flow is purely radial at the inlet of the rotor. The pump has the following characteristics: Flow rate Inlet diameter Outlet diameter Head Width at the inlet Width at the outlet Leakage Mechanical loss Blade angle at the outlet The water density Atmospheric pressure |Q=72 L/s DI = 90 mm D2 = 280 mm H= 25m bl -20 mm b2 = 18 mm q =2 L/s Pm = 1.41 kW B2 = 35 p = 998 kg/m³ 101 kPa