The water level in a wide tank is 20 m, the tank is open to the atmosphere. A hose is connected to the bottom of the tank, and the nozzle at the end of the hose is pointed straight up as shown in the figure below. A pump is connected between the tank and the nozzle. If the maximum height of water column is 27 m above the ground, find the following neglecting the friction losses in the hose and fittings: a) The head of the pump in [m] b) The head of the pump in kPa Take the density of water as 1000 kg/m³ and the gravitational acceleration as 9.81 m/s? 27 m -20 m

The water level in a wide tank is 20 m, the tank is open to the atmosphere. A hose is connected to the bottom of the tank, and the nozzle at the end of the hose is pointed straight up as shown in the figure below. A pump is connected between the tank and the nozzle. If the maximum height of water column is 27 m above the ground, find the following neglecting the friction losses in the hose and fittings: a) The head of the pump in [m] b) The head of the pump in kPa Take the density of water as 1000 kg/m³ and the gravitational acceleration as 9.81 m/s? 27 m -20 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Two pipes A and B are connected in parallel between two points. Pipe A is 200 m long and has a diameter of 16 cm, pipe B is 150 m long and has a diameter of 12 cm. Both the pipes have the same friction factor of 0.018. A partially closed valve in pipe 'A' causes the discharge in the two pipes to be the same. All other minor losses can be neglected. The value of the valve coefficient is - Valve F = 0.018 L=200m, d-16cm L,=150m, d=12cm B F = 0.018
simple solution is needed
Hydrodynamics pumps (WRITTEN COMPLETE SOLUTION AND FIGURES IF NEEDED) 1. A centrifugal pump installation draws water from an open reservoir having a water elevation of 5 m above the pump centerline and delivers the water to another open reservoir 80 m above pump centerline. The rate of discharge is 600 li/min. The suction pipe has a diameter of 200 mm while that of the discharge pipe diameter is 150 mm. The friction loss at the suction is estimated to be 4 times the velocity head at the 200 mm suction pipe. At the discharge, the friction loss is estimated to be 21 times the velocity head at the 150 mm discharge pipe. If the overall mechanical efficiency is 77%, estimate the brake power input to thepump. a. brake power Answer : ____________________ kW
A Pump The oil tanks have a diameter of D = 12m. The initial depth of the oil in tank A is 20m, and in tank B the depth is 1 m. The pump delivers a constant head of 60 m. The connecting pipe has a diameter of b = 0.2m, and the head loss due to friction in the pipe is hyL = 8- Find the time required to fill tank B to 14m depth. (neglect minor losses)
A 30 cm pipe is connected by a reducer to a 10 cm pipe. points 1 and 2 are along the same elevation. the pressure at 1 is 200 Kpa. the flow is 30 litres/s and the energy lost between 1 and 2 is equivalent to 20 Kpa. Compute the pressure at 2 if the liquid flowing is water.
height of water the pressure intensity : () at the interface of the two liquids, and (ii) at the bottom of the tank. [Ans. () 1.57 N/cm", (il) 3.04 N/em 6. An open tank contains water upto a depth of 1.5 m and above it an oil of sp. gr. 0.8 for a depth of 2 m. Find 7. The diameters of a small piston and a large piston of a hydraulic jack are 2 cm and 10 cm respectively, A force of 60 N is applied on the small piston. Find the load lifted by the large piston, when: (a) the piston at the same level, and (b) small piston is 20 cm above the large piston. The density of the liquid in the jackis [Ans. (a) 1500 N, (b) 1520.5 NJ kg given as 1000 - 8. Determine the gauge and absolute pressure at a point which is 2.0 m below the free surface of water. Take [Ans. 1.962 N/cm? (gauge), 12.066 N/cm? (abs.)] - atmospheric pressure as 10.1043 N/cm?. 9. A simple manometer is used to measure the pressure of oil (sp. gr, = 0.8) flowing in a pipe line. Its right limb is open to the atmosphere and left…
Consider the figure shown below. If the flow rate of water from the tank is 0.03 m/s, the pressure at point 2 is 120kPa. Height of water in the tank is 4m and the pipe diameter is 160mm with a friction factor of 0.020. Solve for the height h if the branch line is shut off, and if the branch line is open so that half of the flow from the tank goes into the branch and half continues in the main line. Determine the difference in the head losses in both directions. Neglect minor losses. Vent | 4m 160mmø pipe Branch Line B A 1.75m Main Line 300m 200m ANSWER: a. h = 13.918m, b. h = 10.585m c. HL = 3.2479m
Question is in figure
Please solve in detail.
Water at 10°C flows at the rate of 900 L/min from the reservoir and through the copper tube type K . Compute the pressure at point B, just considering the energy loss due to the straight pipe and neglecting the others losses(elbows and tank outlet)