Water at 25°c is being supplied to an irrigation ditch from an elevated storage reservoir. A 3 m 10 m Long-radius elbow Onipe that wu carn DN 125 Schedule 40 steel pipe Gate valve оpen 2 в 100 m Note: Energy losses are all depend on the velocity at point B. 8 = 4.5x10-5 m a) Write the assumptions you made in order to solve the problem b) Calculate the volume flow rate of water into the ditch c) Calculate the generated power by the flow of water at the exit with 80% efficiency

Water at 25°c is being supplied to an irrigation ditch from an elevated storage reservoir. A 3 m 10 m Long-radius elbow Onipe that wu carn DN 125 Schedule 40 steel pipe Gate valve оpen 2 в 100 m Note: Energy losses are all depend on the velocity at point B. 8 = 4.5x10-5 m a) Write the assumptions you made in order to solve the problem b) Calculate the volume flow rate of water into the ditch c) Calculate the generated power by the flow of water at the exit with 80% efficiency

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Fluid Mechanics Question

Q: An emergency flooding system for a nuclear reactor core i reservoirs are actually at the similar…

Q: 40m 120 1.2L/ Water ervoirs A and B are connected to each other through a 40-m-long, 2-cm swing…

Q: (b) A regulator was constructed to pass a Leliavsky discharge in a canal of depth equals to 2.2 m at…

A: Step 1: Derive a formula to calculate ( h_v ) or ( ΔH) Given:- Depth of the canal at upstream (u/s)…

Q: Water flows in a trapezoidal channel of 2 m width and side slope at 1:1. At upstream depth of 2 m,…

Q: A 1 m diameter new cast iron pipe 800 m long and has a head loss of 1.11 m Find the discharge in…

Q: (c) Figure Q4(c)(i) shows the system consists of 1200 m of 5 cm cast-iron pipe, two 45° and four 90°…

A: L = 1200 mD = 5 cm or 0.05 m Q = 0.005 m3/s = 0.001 kg/m s

Q: Figure shows that the pipe flow of 50 m^3/hr, is driven by pressurized air in the tank.…

A: The flow of fluid includes movement of an unbalanced fluid. As long as unequalled forces are in…

Q: Determine the flow rate in the siphon shown. Diameter of the pipe is 2.5cm. B 1.8m A water 3.6m Your…

Q: Q-4: A flow net for flow around a single row of sheet piles in a permeable soil layer is shown in…

A: Piezometers measure pore water pressure (piezometric level) in the ground using geotechnical…

Q: The pump is used to deliver the water from the pond at A to the channel at B with a flow of 0.03…

A: Q=0.06m3s=vAv=0.03m3sπ4(0.15)2=1.6976ms

Q: 7- a) b) c) d) For the transmission line shown below, what is the power of the pump with efficiency…

A: Efficiency, η=70% Flow rate, Q=200 lit./s The density of water, ρ=9806 N/m3 The slope of the…

Q: Three reservoirs Z, Y, and X meet at junction P. Reservoir Y (25m above Reservoir X) is at Elev.…

A: Step 1

Q: The elasticity and dimension of a pipe are such that the celerity of pressure wave is 975 m/s. The…

A: Given data in question Celerity Discharge Diameter Change in Discharge To find out Water hammer…

Concept explainers

Wind Energy

Wind energy is a renewable energy source that is used to generate electricity by wind power. The term, wind power, means utilization of kinetic energy of wind to generate electricity. Wind energy is termed renewable source energy because it can never be exhausted. There are other renewable energy sources, such as solar energy, geothermal energy, hydropower energy, and so on. All of them contribute to power the thermal energy stations to generate electricity.

Question

Water at 25°c is being supplied to an irrigation ditch from an elevated storage reservoir.
3 m
plos
10 m
getelgmpo L
Long-radius elbow
Gate valve
pe that wlc
I open
2
DN 125 Schedule 40 steel pipe
relevpom.diference
100 m
Note: Energy losses are all depend on the velocity at point B.
E = 4.5x10-5 m
a) Write the assumptions you made in order to solve the problem
b) Calculate the volume flow rate of water into the ditch
c) Calculate the generated power by the flow of water at the exit with 80% efficiency

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Trending now

This is a popular solution!

Step by step

Solved in 6 steps with 6 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

please do step by step The pipe in figure discharges water from an upper tank to a lower tank as shown. The pipe consists of 500-ft long of a 6-in diameter wrought iron (f = 0.016) Neglect minor losses.
3. A pump is discharging 20 lit/sec of water through 100mm diameter smooth steel pipe. When the pump is 720 kPa, the discharge pipe is at a point 540m distant from the pump and 45m higher in elevation. a. What is the velocity of flow on the discharge side of the pump? b. Assuming f = 0.025, compute the head loss of the pipe. c. Compute the pressure expected in the discharge pipe. 540m 100mm dia 2 45 m
T1. Water is to be pumped from a reservoir at datum level 6.5m to a reservoir at datum level 24.8m at the rate of 55.6 l/s by a pump at datum level 9.2m. The suction pipe is 21m of 200mm diameter, and the delivery pipe is 186m of 100mm diameter, both with friction factor 0.015. What head must be generated by the pump. Answer 89.9m Delivery reservoir ha Z₂ hs Suction reservoir Datum Z₁ Pump
SITUATION Water is being discharged (Q = 280 lit/s) from a reservoir through a turbine as shown. Assume C=120 for all pipes. L-50m D-300 mm L-20m D-600 mm EL. 50 m Compute the total head loss due to friction. c. 0.04 m d. 4.39 m 7. a. 2.25 m b. 2.57 m Compute the energy exerted by the turbine to generate 56 kilowatts of power. 8. c. 98.10 m d. 2.56 m a. 20.39 m b. 72.96 m Compute the elevation of the water surface in the reservoir A that would be required for the turbine to generate 56 kilowatts of power. 9. c. 98.10 m a. 20.39 m b. 72.95 m d. 2.56 m 2.872 m c. 2.278 m d. 2.827 m a. b. 2.728 m
A pump is discharging 12 lit/sec of water through 100mm diameter smooth steel pipe. When the pump is 720 kPa, the discharge pipe is at a point 540m distant from the pump and 45m higher in elevation. a. What is the velocity of flow on the discharge side of the pump? b. Assuming f = 0.025, compute the head loss of the pipe. c. Compute the pressure expected in the discharge pipe. 45 m 540m-100mm dia
The pump in the figure B. draws water from a reservoir and discharges through 2 V2 incheshose, which terminates in a nozzle having a jet diameter of inch. The head losses are: I to 2.5.75 ft: 2 to 3. negligible: 3 to 4. 30.76 ft. 4 to 5. I6.7 ft. Compute the required horsepoweroutput of the pump and make a table of the heads at the five points. Q is (a) 276 gpm. (b) 376gpm.
11- In an infinite two-dimensional flow filed, a sink of strength 3/2n m/s.m is located at the origin, and another of strength 4/2n m'/s.m at (2 , 0). What is the magnitude and direction of the velocity at point (0, 2). [0.429 m/s; -68.22°]
A submersible deep well pump delivers 800gal/h of water at 60°F through a 1in SH. 40 SP, when operating in the system shown below. If the total length of pipe is 150ft, calculate the power delivered by the pump to the water. Consider friction loss, but neglect the other minor losses.
F4-1. Water flows into the tank through a rectangular tube. If the average velocity of the flow is 16 m/s, determine the mass flow. Take p, 1000 kg/m'. 16 m/s 50 mmy 60 0.06 m (0.05 m) sin 60