Water at 20°C is flowing in a serial connected piping network with 270 L/min. Pipes have been made of cast iron. Three pipe diameters have been used for this system as 5 cm, 15 cm and 7.6 cm. The lengths of these pipes are 38 m, 23 m, and 45 m, respectively. The elbows and an open globe valve are all flanged. Calculate the extracted power [W] from the turbine. (NOTE: Elevation difference between two reservoirs is 36,26 m)

Water at 20°C is flowing in a serial connected piping network with 270 L/min. Pipes have been made of cast iron. Three pipe diameters have been used for this system as 5 cm, 15 cm and 7.6 cm. The lengths of these pipes are 38 m, 23 m, and 45 m, respectively. The elbows and an open globe valve are all flanged. Calculate the extracted power [W] from the turbine. (NOTE: Elevation difference between two reservoirs is 36,26 m)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The Figure shown below is a parallel pipeline system with two branches used to supply lubricating water to the bearings. The main line and two branches use the same size of pipes. The pressures at section 1 and section 2 are and , respectively. The resistance coefficients for two bearings are and . The cross section areas of two branch pipes are . The energy loss caused by friction can be ignored. The energy loss caused by one bend is . (8) Calculate the velocity in branch b_________m/s
Size the duct system shown in the figure. The air velocity at the inlet is 8m/s. The length of each duct segment is 4m. If the pressure drop in each diffuser and elbow (or Tee branch) is 20Pa and 25 Pa respectively, calculate the pressure head required for the AHU. (Note: CFM=ft³/min.) Pgh xh (чоржъх Dary AHU 600CFM 800CFM 1000CFM 600CFM 800CFM 1000CFM 600CFM 800CFM 1000CFM
3. Petrol is drained from a tank X to tank Y via pipeline A-B (see figure Q3). A pump is then used to pump the petrol from tank Y to tank Z via pipeline C-D. Pipe lengths, diameters and relative heights of the pump and tank levels are as shown in figure Q3. The density of the petrol is 760 kg/m³ and the Fanning friction factor (f) for all the pipes is 0.0075. • For pipe A-B the entrance loss at A is 0.5 • For pipe C-D the entrance loss at C is 0.5 u² • All valve losses are 0.2 each, 2g Neglect any entrance or exit head losses at the pump and all other pipeline component losses. X • The velocity in the pipe C-D cannot exceed 1.8 m/s The pump mechanical efficiency is 86% 10 m L = 50 m D = 100 mm B 00 30 m Y 5m 20 m and the exit loss at B is and the exit loss at D is D = 75 mm L = 10 m Figure Q3 D = 75 mm L = 50 m pump 2g N 10 m
Consider a positive displacement pump; Shaft speed is 1800rpm Pump push 0.003gal/revolution Leakage is 5% of the flow for a pressure of 3000 psi. The pressure and flow at the loadside are rrealted according to the following equation p = 68Q² Q = gal per min P = psi Wat is the operating point of the pump
What’s the answer for this please ?
Write legibly 5. A series galvanized iron pipes (C = 120) consisting of 20 in. diameter of length 8,000 ft, 16 in. diameter of length 7,000 ft, and 14 in. diameter of length 5000 ft carries water at the rate of 4 cfs. (a) Determine the total loss of energy over the entire length of the pipeline. (b) Determine the diameter of an equivalent pipe with a length of 20,000 ft. Determine: a. total loss of energy: _____________ ft b. diameter of an equivalent pipe:___________ in.
None
write legibly Complex Pipeline System_Series Pipes 1. Three new cast-iron pipes were connected in series: pipe 1, 12 in. diameter and 1200 ft long; pipe 2, 24 in. diameter and 2000 ft long; and pipe 3, 18 in. diameter and 1500 ft long. If the total flow in the system is 8.0 cfs, determine the (a) total lost head, ft; and(b) the equivalent length of a 20 in. diameter pipe. Use a C value of 120 for all pipes. (a) total lost head : _______________________ ft(b) equivalent length : _______________________ ft
This is merely a past paper question please assist
Water is pumped through 750 ft of 6-inch nominal diameter Schedule number 40 pipe. The difference in height between the exit and inlet planes is given as 50 ft. Pump Efficiency 80% Pump Motor Power is 20 Horsepower. Friction losses are shown as 50 ft-lbf / lbm. Calculate the flow in the pipeline
The Figure shown below is a parallel pipeline system with two branches used to supply lubricating water to the bearings. The main line and two branches use the same size of pipes. The pressures at section 1 and section 2 are and , respectively. The resistance coefficients for two bearings are and . The cross section areas of two branch pipes are . The energy loss caused by friction can be ignored. The energy loss caused by one bend is . (4) Calculate the energy loss for branch b_________
Kindly answer all the parts correctly and in good handwriting (i.e. handwritten) for an upvote..Thank you