Water at 20°C flows from Tank 1 to Tank 2 through a 2-inch, Schedule 40 pipe as shown in the figure below. The length of the pipe is 100 m and in the pipeline, there are two 90° standard elbows and a gate valve. If both tanks are located at the same datum level, determine the water level in the larger tank if the water level in the smaller one is 4 m from the datum level and the flow rate of water is 1O L/s. [49.66 m] 4m Tank 1 Tank 2 I

Water at 20°C flows from Tank 1 to Tank 2 through a 2-inch, Schedule 40 pipe as shown in the figure below. The length of the pipe is 100 m and in the pipeline, there are two 90° standard elbows and a gate valve. If both tanks are located at the same datum level, determine the water level in the larger tank if the water level in the smaller one is 4 m from the datum level and the flow rate of water is 1O L/s. [49.66 m] 4m Tank 1 Tank 2 I

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: pipes in parallel, the total friction head loss equals to the individual friction head loss in each…

Q: asoline at 77°F flows from a pressurized upper tank to a vented lower tank as shown in the figure…

A: Givenh2=52.8ftTemp=77°Fρgasoline=45lb/ft3

Q: Flow in a turbine flows through the turbine shown in the Figure below. nt A, the velocity in pipe is…

A: GivenVA=11.14m/sPA=1.2bar=120kPaP=0.5bar=50kPaZA=1mhL=0.3mdA=0.2mdB=0.4m

Q: art A - The three tanks shown in the figure below are connected by new cast ire he diameter and…

A: To given thatε=0.26D1=1m=1000mm D2=0.8m=800mmD3=1.2m=1200mmL1=200m…

Q: The three-tanks system in figure are interconnected as shown. Compute the flowrate in each pipe,…

A: To find discharge in all pipes

Q: A submersible pump is to be selected for the installation on a newly drilled deep well. The static…

A: The total dynamic head of the water system determines the various head losses that the pump must…

Q: A piping system has a Y-configuration for separating the flow as shown in Figure 4. The diameter of…

A: Given data:

Q: Determine the energy loss that will occur as 100 Liters / min of water flows from a small copper…

A: When a pipe has a sudden expansion there is a head loss in the flowing fluid across this…

Q: A storage tank has hot water. This water at a temperature of 85 °C is pumped to a 600 cm height at a…

Q: Water (15 C) is transported from an open reservoir to the atmosphere through a new cast iron pipe (d…

Q: Water steadily flows from the basement to the second floor through a 0.75-in-diameter copper pipe.…

Q: Water flows through a reducer in a pipe as shown. The pressure at A is equal to 345 kPa and the…

A: GIVEN DATA - PA=345KPa dA=150mm PB=325KPa dB=60mm WE HAVE TO CALCULATE FLOW RATE

Q: 3.- A swimming pool has a partial filtration system, the water whose temperature is 75 °F, is pumped…

A: The water temperature, T = 75 FThe discharge through the pump, Q1 = 30 GPMThe pressure inside the…

Q: Water at 40 degrees C is flowing from A to B through the system shown below. Determine the…

A: Given data as per question Lz=30m1 in=0.0254 mD1=4 in=0.1016mD2=6 in=0.1524 mPA=PB=Atmospheric…

Q: As shown in the figure, the water flows from the ground floor of a three-storey house to the second…

Q: 2.attention to the piping system shown in the figure below. Pipes 1, 2, and 3 are installed in…

Q: Determine the maximum allowable volume flow rate in L/min that can be carried through a standard…

A: To find-: The maximum allowable volume flow rate in Lmin. Given-: The outside diameter is D=1.25 in.…

Q: (Energy equation) The pump shown in the figure below adds 1.74 horsepower to the water when the…

Q: 3. Water at the rate of 30 litres/sec. is flowing through a 0.2 m. 1.D. pipe. A venturi meter of…

Q: A cast-iron pipe system consists of a 500-ft section of water pipe, after which the flow branches…

A: Applying bernoulli's equation,

Concept explainers

Fluid Dynamics

The study of the flow of gases and liquids, usually in and around solid surfaces, is known as fluid dynamics in physics and engineering. Fluid dynamics, for example, can be used to evaluate the movement of air through an airplane wing or the surface of a vehicle. It can also be used in ship design to increase the speed at which ships pass through water.

Question

Water at 20°C flows from Tank 1 to Tank 2 through a 2-inch, Schedule 40 pipe as
shown in the figure below. The length of the pipe is 100 m and in the pipeline, there
are two 90° standard elbows and a gate valve. If both tanks are located at the same
datum level, determine the water level in the larger tank if the water level in the
smaller one is 4 m from the datum level and the flow rate of water is 10 L/s.
[49.66 m]
2.
4 m
Tank 2 I
FIGURE Q2: Transport of water in tanks
Tank 1
undefined

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Given Data

VIEW

Step 2: Calculating The Velocity of Water

VIEW

Step 3: Calculating The Reynolds Number

VIEW

Step 4: Calculating the Friction Factor

VIEW

Step 5: Calculating The Major Head Loss

VIEW

Step 6: Calculating The Minor Head Loss

VIEW

Step 7: Calculating The Water level in the Larger Tank

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 7 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

5. The water in the right figure is flowing steadily. What is the flow rate? 10 ft 10 ft Y Very large Water 3-in steel pipe
10. Three pipes of lengths 800 m, 600 m and 300 m and of diameters 400 mm, 300 mm and 200 mm respec- tively are connected in series. The ends of the compound pipe is connected to two tanks, whose water surface levels are maintained at a difference of 15 m. Determine the rate of flow of water through the pipes if f = .005. What will be diameter of a single pipe of length 1700 m and f = .005, which replaces the three pipes ?
4. Three storage tanks A, B and C are connected to a piping system as shown in Fig. The flow rate of water in the pipe which is connected to tank B is 0.06 m³/s. Determine the flow rate in the other two pipes and then calculate the level of the water in tank B relative to ground level. Friction factor, f = 0.01. ZA= 25 m A ₁=1000 m d₁= 0.3 m Q₁ = ? l₁= 600 m d,= 0.2 m Q = 0.06 m²/s 1₂= 1300 m d₁= 0.2 m Q₂ = ? B C Zc = 11 m Za
The piping system shown in the figure is to move ethylene glycol at a flow rate of 50 gpm. Follow the suggested design procedure and select a suitable pipe size and pump for the system. A B A: Globe valves (2 of them) B: Union fittings (4 with 2 not shown) C: Plate welded to tank to suppress air entrainment in pump inlet D: Elbows: there are five 90° elbows and two 45° elbows The pipe is all wrought iron, with threaded fittings, schedule 40. Pipe lengths total 35.36 m. Total inlet pipe length from tank to pump is 1.22 m. z1 = 1.22 m and z2 = 3.66 m.
Water flows in a pipe of 1-in. diameter at a temperature of 70°F. The pressure values at points 1 and 2 are found to be 20 psi and 25 psi, respectively. The elevation of point 1 is 12 feet, and the elevation of point 2 is 0 feet. There is 15 feet of pipe between the two points. a. Determine the direction of flow. b. What is the minimum discharge above which the flow will not be laminar?
6.5 BELLOWS 6100mm The horizontal elbow is joined by bellows to the rest of the piping system and it transports water. Determine the X and Y components of the force needed to keep the elbov in posi- tion. The pressure at A and B is 200 kPa, the flow rate is 30 L/s and the pipe diameter is 100 mm. 6.6 Water flows at a rate of 0,055 m³/s through a piping system and then issues from the pipe of 50 mm diameter into the atmosphere. Ø150mm Ø50mm Ignore losses in the pipe and determine the force required at the flange to keep the nozzle in position. (Hint: first determine the pressure at A with Bernoulli's equation.)
3. Petrol is drained from a tank X to tank Y via pipeline A-B (see figure Q3). A pump is then used to pump the petrol from tank Y to tank Z via pipeline C-D. Pipe lengths, diameters and relative heights of the pump and tank levels are as shown in figure Q3. The density of the petrol is 760 kg/m³ and the Fanning friction factor (f) for all the pipes is 0.0075. • For pipe A-B the entrance loss at A is 0.5 • For pipe C-D the entrance loss at C is 0.5 u² • All valve losses are 0.2 each, 2g Neglect any entrance or exit head losses at the pump and all other pipeline component losses. X • The velocity in the pipe C-D cannot exceed 1.8 m/s The pump mechanical efficiency is 86% 10 m L = 50 m D = 100 mm B 00 30 m Y 5m 20 m and the exit loss at B is and the exit loss at D is D = 75 mm L = 10 m Figure Q3 D = 75 mm L = 50 m pump 2g N 10 m
Fluid Mech 1. compute for the velocity at a nozzle 2. velocity at A 3. compute the height above the nozzle to which the water will shoot. assume the negligible head loss
Starting from the Bernoulli equation and conservation of mass equation, derive the flow rate equation for the pipe shown in Figure Q2. Then, determine the magnitude of the flow rate.
The pressure through a section of pipe is 23 PSI and the velocity of the fluid is 3 ft/sec. If the velocity was increased to 5 ft/sec, what would the pressure drop be?
For the system shown below, calculate the vertical distance (in meters) between the surfaces of the two reservoirs when water at 10°C flows from A to B at the rate of 0.03 m3/s. The elbows are standard. The inlet is inward projecting, and the exit is square edged. The total length of the 4-in pipe is 94 m. For the 6-in pipe it is 274 m.
Fast pls solve this question correctly in 5 min pls I will give u like for sure Aka