The long tube shown in (Figure 1) has a diameter of 5.0 mm in the wider section and 1.6 mm in the narrower section. Water at 20° C flows from the open end at 0.020 L/s. The flow can be modeled as having a constant average speed through each of the two constant-diameter sections, but it speeds up in the tapered section. The tapered section is so short, much less than 1.0 m in lenath. that viscositv can be Figure P 1.0 m 1.0 m <1 of 1

The long tube shown in (Figure 1) has a diameter of 5.0 mm in the wider section and 1.6 mm in the narrower section. Water at 20° C flows from the open end at 0.020 L/s. The flow can be modeled as having a constant average speed through each of the two constant-diameter sections, but it speeds up in the tapered section. The tapered section is so short, much less than 1.0 m in lenath. that viscositv can be Figure P 1.0 m 1.0 m <1 of 1

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

-.1 A pipe of diameter 300 mm and length 3 000 m is used for the transmission of power by water. The total head at the inlet of the pipe is 400 m. Find the maximum power available at the outlet of the pipe. Take f = 0.005. 2 The head of water at the inlet of a pipe of length 1 500 m and diameter 400 mm is 50 m. A nozzle of diameter 80 mm at the outlet, is fitted to the pipe. Find the velocity of water at the outlet of the nozzle if f = 0.01 for the pipe. %3D %31
5. Kerosene (sp.gr. = 0.88 ) enters the cylindrical arrangement as shown on the figure at section 1 at 0.08 N/s. The 80 mm diameter plates are 3 mm apart. Assuming steady flow and unit weight of water is 9790 N/m3 (a) Compute the inlet average velocity Vị (b) Compute the outlet volume flux in m/sec (c) Compute the average velocity V2 assuming radial flow in mm, m/sec D=80 mm 3 mm 4 mm 4 mm
A 6 in. pipe, as shown in the figure, takes water from a reservoir and terminates in a nozzle having a jet diameter of 2 in. Assuming a nozzle loss of 8 percent of the velocity head in the jet, compute the discharge (in S.I. units). Also, make a table showing the elevation head, velocity head, pressure head, and total head at each of the six stations. Lastly, draw the hydraulic gradient line (H.G.L.) & the energy gradient line (E.G.L.).
10.0 m 200 m 2. An old western town has a water tower to deliver water to the residents. Pictured above is the water tower. The water tower is closed but there is a section of air that is atmospheric pressure just above the water. The corsss ectional area at point 2 is 4.75 x 10 m. The cross sectional area fot the water tower is very large. What is the speed of the water coming out of the pipe at point 2? (density of water = kg/m³) 3. On a vacation trip up in Oregon my boys decided to build a 10 kg raft that they made out of driftwood. 1000
a! Water flowing through a tapering pipe having diameters of 300mm and 150mm at section one and two respectively. The discharge through the pipe 40 Liter/s. the section 1 is 10 m above the datum and section 2 is 6 m above the datum. Find the pressure at section 2if that at section 1 is 400 KN/m2. 10 6. m Datum
A vertical pipe of 2.5 m diameter and 25 m length has a pressure head of 6.5 m of water at the upper end. When water flows through the pipe at an average velocity of 5 m/s, the head loss due to friction is 1.3 m. Find the pressure at the lower end of the pipe, when the flow is upward only with neat diagram.
Water is pumped at a rate of 21.4 m/s from tank (A) and out through a 300.5 m pipe to tank (B). The surface roughness of the pipe is 0.046 mm. When the water levels are as shown in the given figure, the head provided by the pump is 70 m, Calculate the pipe diameter (mm) if the water temperature is 10°C (do not assume the water mass density and the ViScosity), Usef 0.02 for the first iteration and try only one more iterations (two in total) by using Swamee and Jain formula. Elevation 135 Elevation 140 m Tank (B) Tievation 100m Tank LA) Jund: Elevitions in Write the answer for any numbers after the declmal
In a pipe of diameter 300mm the center line velocity and the velocity at a point 100mm from the center, as measured by pitot tube are 2.4 m/s and 2.0 m/s respectively. Assume the flow in the pipe to be turbulent find: 1-Dischrge through the pipe,2-Coefficient of friction, 3 Height of roughness projections.Please do not waste my question solve with correct answers only.
Water at 80°F flows from a storage tank through 618 ft of 6-in Schedule 40 steel pipe, as shown in the figure. Taking the energy loss due to friction into account, calculate the required head hin feet above the pipe inlet to produce a volume flow rate of 1.65 ft³/s. (round the final answer to three significant figures) h 6-in Schedule 40 steel pipe pipe length
points A and B are given as 29.43 N/cm2 and 22.563 N/cm respectively while the datum head at A and 266 Fluid Mechanies Problem 6.7 A pipe of diameter 400 mm carries water at a velocity of 25 m/s. The pressures c B are 28 m and 30 m. Find the loss of head between A and B.
find the diameter of pipe of length 2500m when rate of flow of water through pipe is 0.25m cube/sec and head lose due to friction is 5m . take C=50 in chezy's formula
4. The system in Fig. consists of 1200 m (length) of 0.05 m (diameter) cast iron pipe, two 45° long-radius elbows, four 90° flanged long-radius elbows, and a fully open globe valve. If the elevation at point 1 is 400 m, what gage pressure is required at point 1 to deliver 0.005 m³/s of water at 20°C into the reservoir? Average surface roughness of cast iron is ε = 0.26 mm. For water at 20°C, take density, p = 998 kg/m³; dynamic viscosity, μ = 0.001 Pa-s; and acceleration due to gravity, g = 9.81 m/s². 90° elbow: KL90, elbow K₁ = 0.5 ent Elevation (1 400 m = 0.3 45° elbow: KL45,elbow=0.2 Elevation 500 m ! Sharp exit Open KL = 10 globe valve Klexit = 1