View Policies Current Attempt in Progress Determine the force in each member of the loaded truss as a result of the hanging weight W = 130 lb. The forces are positive if in tension, negative if in compression. 2 B W = 130 Ib Answers: AB = i Ih AC = i Ib ВС - Ib Save for Later Attempts: 0 of 1 used Submit Answer

Q: Where is the Energy Balance?

A: to find energy balance we need to write the mechanical energy conservation equation i.e. bernoulis…

Q: A four stroke eight cylinders square gasoline engine operating at 3000 rpm has a bore equal to 86…

A: Given data  N=3000 rpm d=86 mm ηm=82% ηv=83% T1=300 K  P1=100 KPa   Pimp=1500 KPa K = no. of…

Q: A dryer is designed to evaporate a constant amount of water every hour. When the dryer runs using 5…

A:

Q: I want the theory part about Jaw Crusher,  its types, its Applications, advantages and disadvantages…

A: JAW CRUSHER A jaw or toggle crusher consists of a set of vertical jaws, in which one jaw is fixed…

Q: FIGURE 21.11 (a) Forces acting in the cutting zone during two-dimensional cutting: note that the…

A: The main aim of lubrication in machining is to reduce the frictional forces. To determine the effect…

Q: If the cylinder in Problem 6 has a stroke of 40 cm, what is the maximum cycle rate that might be…

A:

Q: omitted: (a) The crank shaft is responsible for the conversion of linear motion into rotational…

A:

Q: Q1. (a) Discuss the factors that have to be considered in the design of an engine cylinder. (b) The…

A: Since  all questions are different, according to our guidelines, we are supposed to the answer 1st…

Q: (d) In one production line, there is ultrasonic machines (USM) and electro- discharge machines…

A: USM stands for Ultrasonic Machining USM is a mechanical energy based non-traditional machining…

Q: 2. Explain the advantage and disadvantages of DuFort-Frankel and Crank- Nikolson methods.

A: In numerical analysis, the Crank–Nicolson method is finite difference method used for numerically…

Q: Taking into account only the thermal expansion, explain why both the "Block" of the engine (and…

A: The engine block and the piston are made of different materials to allow appropriate amounts of…

Q: State and explain the simple change you would have to make to your FLUENT setup to see a shock in…

A: Ansys fluent is a cae software package of ansys which uses finite volume method to solve simulation…

Q: Which one is wrong about the traditional manufacturing methods?(Alışılmış O A) Team vibration is…

A: The cutting speed of a material depends upon several factors.

Q: 8. AB

A: 1. Structure 2. Pressing cylinder 3. Control panel 4. Pressing shaft 5. Hopper 6. Pressing head

Q: What down the external sources of induced foot?

A: The external sources of induced foot are:-

Q: Do you think that a perpetual motion machine will ever be possible to make? Why or why not?

A: Perpetual motion machine is that machine which converts entire heat input to work output. That means…

Q: What are some of the main materials challenges in running jet engines at high temperatures? Select…

A: Given data:-Jet engines:-Jet engines propel aircraft by expelling high-speed exhaust gases. Air is…

Q: (11) A 120cm diameter diamond circular blade, mounted on a pulley-driven steel shaft, is requiring a…

A: Given data, Diameter of the diamond blade, D = 120 cm = 1.2 m Peripheral linear speed of the blade,…

Q: 1. A single cylinder petrol engine works on the Otto cycle and draws in air at 1.01 bar and 22°C.…

A:

Q: When does the Stress concentrations occur in shafts?

A: A resisting force produced in a body on each unit area to counter the deformation of the body is…

Q: Why balancing of the rotating masses is necessary for machines with any two industrial applications…

A: Why balancing of the rotating masses is necessary for machines : The balancing of rotating masses is…

Q: why the temperature increases during the compression proc

A: Given data Why the temperature increases during the compression process.

Q: why the drone are not popular (limited)??? and what the challanges of the drones ???

A: Drone: The word " drone" refers piloted aircraft. It is also known as unmanned aerial vehicle. These…

Q: A kick is defined as an unplanned formation fluid entry into the wellbore annulus. a. True b. False

A: A kick tends to occurs in  oil well when the pressure exerted by the rock surrounding the bore is…

Q: What are the strokes of a four‑stroke cycle?

A: Inlet stroke- during this process piston moves from TDC to BDC inhaling air fuel mixture into the…

Q: 6. Conceptual Question: Explain why a long pole is more beneficial to a tightrope walker if the pole…

A: Tight rope walker: A person who entertains others by walking across a tightrope, which is a tightly…

Q: How effective the waste water can be removed from crude oil and explain the process?

A: Given Crude oil To find Process of wastewater treatment

Q: Why should managers in the car manufacturing industry be aware of Moore’s Law? Besides the…

A:

Q: The lead screw of a lathe has a 2.0-in Acme thread, 2½TPI. To drive the tool carriage, this screw…

A:

Q: 14A) is between moving surfaces that are separated by a layer of fluid. O a. Static friction. Ob.…

A: This is a fluid friction which occurs between fluid layers that are moving to each other which…

Q: 11) A 120cm diameter diamond circular blade, mounted on a pulley-driven steel shaft, is requiring a…

A: Given data : Kinetic energy=K.E Mass of car=m To find : (a) the shaft rpm to attain blade peripheral…