View Policies Current Attempt in Progress A load of P = 150 kN is supported by a structure consisting of rigid bar ABC, two identical solid bronze [E = 100 GPa] rods (1), and a solid steel [E = 200 GPa] rod (2), as shown in the figure. All rods are unstressed before load P is applied to the rigid bar directly underneath joint B. Assume perfect connections at all joints. The bronze rods (1) each have a length of L1 = 2250 mm, a diameter of 28 mm, and a cross-sectional area of 616 mm?. Steel rod (2) has a length of L2 = 1750 mm, a diameter of 20 mm, and a cross-sectional area of 314 mm?. Determine the axial force that is produced in steel rod (2) after load P is applied to the rigid bar. a a (1) (1) L1 L2 (2) OB Answer: P2- i kN

View Policies Current Attempt in Progress A load of P = 150 kN is supported by a structure consisting of rigid bar ABC, two identical solid bronze [E = 100 GPa] rods (1), and a solid steel [E = 200 GPa] rod (2), as shown in the figure. All rods are unstressed before load P is applied to the rigid bar directly underneath joint B. Assume perfect connections at all joints. The bronze rods (1) each have a length of L1 = 2250 mm, a diameter of 28 mm, and a cross-sectional area of 616 mm?. Steel rod (2) has a length of L2 = 1750 mm, a diameter of 20 mm, and a cross-sectional area of 314 mm?. Determine the axial force that is produced in steel rod (2) after load P is applied to the rigid bar. a a (1) (1) L1 L2 (2) OB Answer: P2- i kN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The pin-connected structure consists of a rigid bar ABCD and two axial members. Bar (1) is bronze [E = 110 GPa] with a cross-sectional area of A₁ = 630 mm². Bar (2) is an aluminum alloy [E = 79 GPa] with a cross-sectional area of A₂ = 340 mm². A concentrated load of P = 52 kN acts on the structure at D. Assume L₁=910 mm., L₂=430 mm., a=450 mm., b=280 mm., and c=1030 mm. Determine: (a) the normal stresses 0₁, 02 in both bars (1) and (2). (b) the downward deflection vp of point D on the rigid bar. a 5 Answers: (a) 6₁ (b) VD= = tel i (1) L₁ L2 B C MPa, 0₂ = mm. i MPa
The pin-connected structure consists of a rigid beam ABCD and two supporting bars. Bar (1) is an aluminum alloy [E = 79 GPa] with a cross-sectional area of A₁ = 700 mm². Bar (2) is a bronze alloy [E = 106 GPa] with a cross-sectional area of A₂ = 480 mm². Assume L₁=1.8 m, L₂=2.1 m, a=0.5 m, b=1.6 m, and c=0.8 m. All bars are unstressed before the load P is applied; however, there is a 3.4-mm clearance in the pin connection at A. If a load of P = 53 kN is applied at B, determine: (a) the normal stresses 01, 02, in both bars (1) and (2). (b) the normal strains 1, 2, in bars (1) and (2). (c) determine the downward deflection VA of point A on the rigid bar. (1) A Answers: (a) σ₁ = (b) 1 (c) VA = i a L₁ B b (2) L2 MPa, 0₁ = με, €2 = mm. i i D MPa. με.
The pin-connected structure consists of a rigid bar ABCD and two axial members. Bar (1) is bronze [E = 92 GPa] with a cross-sectional area of A₁ = 680 mm². Bar (2) is an aluminum alloy [E = 74 GPa] with a cross-sectional area of A₂ = 350 mm². A concentrated load of P = 56 kN acts on the structure at D. Assume L₁=900 mm., L2=600 mm., a=580 mm., b=310 mm., and c=1160 mm. Determine: (a) the normal stresses 01, 02 in both bars (1) and (2). (b) the downward deflection vp of point D on the rigid bar. b Answers: (a) o₁ = (b) VD= i i L₁ L2 (2) B C MPa, 0₂ = mm. i D MPa
The pin-connected structure consists of a rigid bar ABCD and two axial members. Bar (1) is bronze [E = 90 GPa] with a cross-sectional area of A1 = 510 mm². Bar (2) is an aluminum alloy [E = 68 GPa] with a cross-sectional area of A2 = 320 mm². A concentrated load of P - 75 kN acts on the structure at D. Assume L1-840 mm., L2-420 mm., a-650 mm., b-260 mm., and c-1070 mm. Determine: (a) the normal stresses o1,02 in both bars (1) and (2). (b) the downward deflection vp of point D on the rigid bar. L2 B b D Answers: (a) oi = i MPa, 02 = i MPa (b) VD - i mm.
The compound shaft consists of a solid aluminum segment (1) and a hollow brass segment (2) that are connected at flange B and securely attached to rigid supports at A and C. Aluminum segment (1) has a diameter of 0.55 in., a length of L₁ = 40 in., a shear modulus of 3800 ksi, and an allowable shear stress of 5.8 ksi. Brass segment (2) has an outside diameter of 0.45 in., a wall thickness of 0.15 in., a length of L₂ = 30 in., a shear modulus of 6400 ksi, and an allowable shear stress of 8.2 ksi. Determine: (a) the allowable torque Te that can be applied to the compound shaft at flange B. (b) the magnitudes of the internal torques in segments (1) and (2). (c) the rotation angle of flange B (relative to support A) that is produced by the allowable torque TB. L₁ L2 TB (1) Answer: (a) TB= (b) T₁ = T2= (c) OB= B lb-ft lb-ft lb-ft rad (2) C
Compound axial member ABC has a uniform diameter of d = 1.25 in. • Segment (1) is an aluminum [E1 = 10000 ksi] alloy. The length of segment (1) is L1 = 100 in. %3D Segment (2) is a copper [E2 = 17000 ksi] alloy. The length of segment (2) is L2 = 140 in. %3D When axial force Pis applied, a strain gage attached to copper segment (2) measures a normal strain of ɛ2 = 1500 uin./in. in the longitudinal direction. What is the total elongation of member ABC? L1 P L2 A Aluminum В d Copper c'P Answer: AL = in. %3D
Compound axial member ABC has a uniform diameter of d = 1.25 in. • Segment (1) is an aluminum [E1 = 10000 ksi] alloy. The length of segment (1) is L1 = 100 in. • Segment (2) is a copper [E2 = 17000 ksi] alloy. The length of segment (2) is L2 = 140 in. When axial force Pis applied, a strain gage attached to copper segment (2) measures a normal strain of ɛ2 = 2300 uin./in. in the longitudinal direction. What is the total elongation of member ABC? L2 (1) Aluminum B (2) Copper Answer: in, AL = i
3) The rigid link is supported by steel wire (1) with an unstretched length of 200 mm and cross-sectional area of 22.5 mm?. Member (2) is a short aluminum of initial length 50 mm and cross-sectional area of 40 mm?. The modulus of elasticity of the steel wire is 200 GPa and the aluminum block is 70 GPa. a) Draw the deflected shape of the rigid member and clearly label the deformation of members (1) and (2). b) Write the equilibrium and compatibility equations needed to solve the problem along with the supporting sketches. Hint: Be sure to carefully consider if the members are elongating or shortening; this must be represented mathematically. c) Calculate the internal forces in both axial members and clearly indicate tension or compression. [Ans. to Check: F2 = 535 N]
The compound shaft consists of a solid aluminum segment (1) and a hollow brass segment (2) that are connected at flange B and securely attached to rigid supports at A and C. Aluminum segment (1) has a diameter of 0.95 in., a length of L1 = 50 in., a shear modulus of 3800 ksi, and an allowable shear stress of 6.7 ksi. Brass segment (2) has an outside diameter of 0.85 in., a wall thickness of 0.13 in., a length of L2 = 38 in., a shear modulus of 6400 ksi, and an allowable shear stress of 8.0 ksi. Determine:(a) the allowable torque TB that can be applied to the compound shaft at flange B.(b) the magnitudes of the internal torques in segments (1) and (2).(c) the rotation angle of flange B (relative to support A) that is produced by the allowable torque TB.
The aluminum rod AB (Gal = 27 GPa) is bonded to the brass rod BD (Gbr = 39 GPa). The portion CD of the brass rod is hollow and has an inner diameter of 40 mm. If the allowable shear stresses for the aluminum and brass are 90 MPa and 70 MPa, respectively, and the allowable angle of twist of the free end A is 6 degrees, determine the maximum permissible value of T
The pin-connected assembly consists of aluminum rods (1) and (2) and steel rod (3). The aluminum rods each have a diameter of 11 mm and an elastic modulus of E = 78 GPa. The steel rod has a diameter of 16 mm and an elastic modulus of E = 200 GPa. Assumea = 4.1 m, b= 1.2 m, and c= 1.2 m. What is the magnitude of load P that is necessary to displace point A 12 mm to the left? a (1) (3) A B (2) Answer: P = i kN
Load P is applied to joint D and the temperature increases by 50 °F. There are two steel (E = 29*10^6 psi; a = 6.5*10^-6/°F) AD and DC and a bronze (E = 16*10^6 psi; a = 9*10^-6/°F) BD with a length of 50 inches. Each bar is a 0.75 inch diameter. Find the deformation of every rod, the displacement at D, and the stress in each rod.