VI. The height of a ground floor interior column in reinforced concrete frame with-ou sides-way from the foundation level to the top of the slab is 4m. The column has a square section of b=h=250mm. The concrete grade is of C25, the reinforcements is 4 numbers and the diameter is 16 bars of HRB335 arranged symmetrically in the section. If the axial load is 650KN, check the appropriateness of this Member. Data : C25 concrete fc=11.9MP Because the longer side is less than 300mm, so fc=0.8×11.9MP=9.52MPA ww HRB335 steel (f,=300N/mm²)

VI. The height of a ground floor interior column in reinforced concrete frame with-ou sides-way from the foundation level to the top of the slab is 4m. The column has a square section of b=h=250mm. The concrete grade is of C25, the reinforcements is 4 numbers and the diameter is 16 bars of HRB335 arranged symmetrically in the section. If the axial load is 650KN, check the appropriateness of this Member. Data : C25 concrete fc=11.9MP Because the longer side is less than 300mm, so fc=0.8×11.9MP=9.52MPA ww HRB335 steel (f,=300N/mm²)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 8 m simply supported singly reinforced beam has a width of B= 39 cm and a height H=61 cm. Concrete compressive strength, f'c-30 MPa Steel Yield Strength of longitudinal bars, fyl-420 MPa, Steel Yield Strength of transverse bars, fyt -280 MPa, Unit weight of concrete, 24.4 kN/m³. Steel cover of the beam = 6 cm It is desired that the capacity of the beam to be at balanced condition. If the structural engineer wants the optimization ratio of the design moment and capacity to be 0.66, calculate the maximum value of the live load in kN/m to meet such condition Use NSCP2015
I need the answer to the question in reinforced concrete
Answer the following for the section at Point D Only Calculate the distributed load "w" that: Will cause the section crack Will cause the reinforcement to yield. Material Properties: F'c = 5000 psi Fy = 60000 psi Es = 29000000 psi Ln = 27 ft L wl₂² 16 wl,² 14 CD L wl,2 vl₁² 10 11 win² 16 h: 28 in A=4 in² b=14 in n d: 25 in
5. The beam-column has a height of 7.5m and is a member of a braced frame. It is subjected to an axial load of DL-65KN and LL= 1OOKN. It is pinned at both ends. A W12X35 section was used and was made up of A-36 steel with Fy-250MPA. Compute the interaction value for beam- column based on NSCP 2015 code provisions. Ngelect the weight of the section. A = 6645 mm2 Zx- 839x10^3 mm3 d- 317.50mm Sx- 747x10^3 mm3 tw= 7.62 Rx= 133.35 bf= 166.62 ly= 10x10^6 mm4 tf- 13.21 Sy= 122x10^3 mm3 Ix= 119x10^6 mm4 Ry3 39.12mm 3.5 Note: Use C=D1.00%--0.2
A reinforced concrete simply supported beam has a span of 20 ft and supports service dead load of 2.5 kip/ft and a uniform service live load of 2.5 kip/ft in addition to its self-weight. Design a beam section as per ACI 318-14 to resist the factored external bending moment. The concrete compressive strength at 28 days is(4 + 15)ksi and yielding strength of steel is (60+ 15)ksi.
Solve it
Consider the same beam as in Problem 1. It carries a live load of 3 kips/ft. 8" 8" V (kips) wl M (kips) 9 w/² 128 6" 6 #6 7.5 ft. 7.5 ft. A WL =3 kips/ft. 1 =20 ft. 6 #9 500 8 5 ft. B wl 8 -W/2 B
Design a bearing plate of A36 (Fy = 248 MPa) steel to support a beam reaction consisting of 90-kN dead load and 225-kN live load. Assume that the bearing plate will rest on concrete with a surface area larger than the bearing area by an amount equal to 25 mm of concrete on all sides of the plate. The beam is a W27 × 94 with F₁ = 345 MPa and the concrete strength is fe' = 21 MPa. Use LRFD. I B ln
For the following plan it is required to: 1- Design all beams for flexure and shear, where they have additional 30 kN/m distributed factored load 2- Design the columns. The concrete has a strength of 30 MPa, and the yield strength of the steel is 420 MPa. Show full calculations and neat sketches. All dimensions are in m. I 03 B2 0,3 7 B1 Wu=20 kN/m2 B1
The service load bending moments on a beam are 128 kip-ft for dead load and 107 kip-ft for live load. The beam is 12 in. wide, f'c is 3000 psi and fy is 60 ksi. Determine Mu. Mt. p. R. the depth of the beam and the As of tensile reinforcing required. How many no. 8 bars or No. 10 bars would have the required As?
Plzz Answer this question Assume data if necessary?
3-2 A rectangular section with width b=200mm and depth h=450mm is to carry a design bending moment M=145KN •m. The concrete is of grade C40 and the tensile steel is of HRB400. The tension reinforcement A, is required.