Problem No.1: Determine the maximum factored load Wu (use unit weight of concrete = 24kN/m³) for the doubly reinforced rectangular beam section shown at midspan with 12mm stirrups. The beam is exposed to weather with concrete cover of 50mm. Use fe-31.05 MPa and grade 60 reinforcing bars. A =2-16mm A. = 8-36mm 2/3-bars bundled 400mm 650mm Pu= 15kN ↓↓↓ 7777 1.50 m 6.00m Pu= 15kN 1.50 m

Problem No.1: Determine the maximum factored load Wu (use unit weight of concrete = 24kN/m³) for the doubly reinforced rectangular beam section shown at midspan with 12mm stirrups. The beam is exposed to weather with concrete cover of 50mm. Use fe-31.05 MPa and grade 60 reinforcing bars. A =2-16mm A. = 8-36mm 2/3-bars bundled 400mm 650mm Pu= 15kN ↓↓↓ 7777 1.50 m 6.00m Pu= 15kN 1.50 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

DETERMINE THE MOMENT OF INERTIA OF THE BUILT-UP SECTION ABOUT THE INDICATED X. AXIS. The thickness of the stem in problem 2 is 1.5". Please show clear and complete solution in tabulated form. Thank you
The nails are on both sides of the beam and each can resist a shear of 3 KN. In addition to the distríbuted loading, determine the maximum load P that can be applied to the end of the beam. The nails are spaced 200 mm apart and the allowable shear stress for the wood is Tallow4MPa. 3.Om 300m 30m 300mat Bomm
In a slab-floor system with the total depth of 22 in., the flange effective width was determined to be 40 in. The beams have a web width of 14 in. and the slab thickness is 3 in. Design the reinforcement for a typical interior beam if the factored applied moment, Mu is 9500 k-in. f’c = 6ksi and fy = 80 ksi. Draw the detailing.
Combined Stresses Given Hollow Steel Section (HSS) that is 4"x6" and 1/2" thick, with axial and transverse loading shown, determine the total normal stress at a. The 5k load on the bottom of the beam b. At the mid-span in the middle of the beam C. At the 10k load on top of the beam 5k 10k A 5' 10' 5' B CENTROID 4" 5 k 3k 8k 6" 2' 6.25k 8.75k +6.25k SECTION +1.25k 'V" -8.75k +43.75k-ft. +31.25k-ft. 'M' 8k 5 k + tension P = Ok %3D
Thank youu
Topic: BEAM BEARING PLATES AND COLUMN BASE PLATES - STEEL DESIGN
A reinforced concrete cantilever beam is shown below. The beam cross section is a rectangle, 12 inches deep by 18 inches wide. Material properties are: - Concrete weight: wt = 150 pcf - Concrete compressive strength: f'c = 4000 psi - Concrete tensile strength: f't = 400 psi - Steel tensile strength: fy = 60 ksi - Stirrup consists of #4 bar - Beam is not exposed to weather or in contact with soil. Determine if the beam will crack under its own weight, if its self-weight is 250lb/ft. 10 ft -18" BEAM SECTION beam will crack beam will not crack unknown, not enough information to calculate
t 4#9 1) fé= 5000 psi r Grade 60 steel; 4 #9 Rebars, 5-9" t 4#9 NWC, 5-9" L = 25 ft & Mn = ? 4#9 14" $ 21" #3" Simple span 39
A simply supported beam section was investigated and found out the following elements: b=250mm h=450mm concrete cover = 40mm diameter of stirrups = 10mm fy = 276Mpa f'c = 34.5 Mpa Bot bar reinforcement: 2pcs-20mm Determine the Maximum steel ratio permitted by the code answer in millimeter and 4 decimal places.
A3. A composite beam and deck system made up of W360x72 at 1000mm o.c. is to span 8m. The deck when cast is to be 100mm thick concrete (25MPA). The shear studs to be used have an ultimate stress capacity of 415MPA and will have a diameter of 16mm. Assuming 100% connection and that the system is shored during casting determine the ultimate moment of the composite W360.
Determine the maximu m allowable lo ad P that 1-90. can be safely supported by the frame if t= 30 m m an d 90 mm. The wood has a normal fa ilure stress of b = MPa, and a she ar failure stress o f Tfall Ofail 4 2 10.5 MP a. Use a factor of safety again st failure of 2. 75 mm 75 mm B 30
Design the reinforcement of a rectangular beam to resist a dead load moment of 200kN.m (including its own weight) and a live load moment of 300kN.m. The beam is limited in size to 350mm by 600mm overall depth. Steel covering from centroid of bars to outermost fiber is 100mm for both tension and compression reinforcement. Use fc'=27.5Mpa, fy = 414MPa,20mm bars.A. As'= 7 of 20mm and As=14 of 20mmB. As' = 9 of 20mm and As=18 of 20mmC. As'= 5 of 20mm and As=10 of 20mmD. As' = 3 of 20mm and As=6 of 20mm Please provide neat and clear solutions Note: Kindly double check your answer